Advertisement
Quick Links
Advertisement
Related Manuals for Danfoss DEVIreg 132
Summary of Contents for Danfoss DEVIreg 132
- Page 1 Installation Guide DEVIreg™ 132 Electronic Thermostat www.DEVI.com...
- Page 2 DEVIreg™ 132 Installation Guide...
-
Page 3: Table Of Contents
DEVIreg™ 132 Table of Contents Introduction ..... . . Technical Specifications ... . Safety Instructions . -
Page 4: Technical Specifications
DEVIreg™ 132 Technical Specifications Operation voltage 220-240 V~, 50 Hz Standby power consumption Max 5W Relay: Resistive load Max 16 A / 3680 W @ 230 V Inductive load cos φ= 0.3 max 1 A Sensing units NTC 15 kOhm at 25 °C Sensing values: 0 °C 42 kOhm... -
Page 5: Safety Instructions
DEVIreg™ 132 Dimensions 82 x 82 x 36 mm Weight 90 g The product complies with the EN/IEC Standard “Automatic electrical controls for household and similar use”: • EN/IEC 60730-1 (general) • EN/IEC 60730-2-9 (thermostat) Safety Instructions Make sure the mains supply to the thermostat is turned off before installation. -
Page 6: Mounting Instructions
DEVIreg™ 132 • Always connect the thermostat to continuous power supply. • Do not expose the thermostat to moisture, water, dust, and excessive heat. Mounting Instructions Please observe the following placement guidelines: Place the thermostat at a suitable height on the wall (typically 80-170 cm.). - Page 7 DEVIreg™ 132 Note: A floor sensor enables a more accurate temperature control and is recommended in all floor heating applications and mandatory under wooden floors to reduce the risk of over-heating the floor. • Place the floor sensor in a conduit in an appropriate place where it is not exposed to sunlight or draft from door openings.
- Page 8 DEVIreg™ 132 Follow the steps below to mount the thermostat: Open the thermostat: • Remove the button to get access to the screw which holds the front. • Loosen the screw. • Push down the release tab at the top of the thermo- stat using a flat object while slowly pulling off the front cover.
- Page 9 DEVIreg™ 132 Fasten the thermostat directly to the wall by driving the screws through the holes in each side of the thermostat. = Screw holes for fastening the thermostat. Connect the thermostat according to the connection diagram. LOAD LOAD Max.Load Mains 16 (1) A...
-
Page 10: Settings
DEVIreg™ 132 Set the maximum floor temperature between 20 °C and 50 °C by using a thin screwdriver on the black electronic component with temperature indications in the upper right corner. Install the front cover and button in the reverse order of disassembly. - Page 11 DEVIreg™ 132 • Floor manufactures often specify the max tempera- ture on the top surface of the floor (usually 27-28 °C). • By default, the maximum floor temperature is set to 35 °C. • Always use a floor sensor or a room + floor sensor combination to control floor heating.
-
Page 12: Warranty
The DEVIwarranty shall not extend to products which have not been paid in full. Danfoss will, at all times, provide a rapid and effective response to all complaints and inquiries from our customers. - Page 13 DEVIreg™ 132 Installation Guide...
-
Page 14: Disposal Instruction
DEVIreg™ 132 Disposal Instruction Installation Guide... - Page 15 Danfoss A/S Nordborgvej 81 6430 Nordborg, Syddanmark Denmark 08091252 & AQ059486461368en-020102 © Danfoss | 05.2022...