Related Manuals for Eaton RSPF Series
Summary of Contents for Eaton RSPF Series
- Page 1 Instruction Leaflet: Installation Instructions for Eaton RSPF Series IL158004EN Surge Protective Device (SPD) Rev. 2 – December 2017 Effective Date December 2017 For more information visit: www.eaton.com/RSPF...
-
Page 2: Table Of Contents
Product improvements and enhancements are continuous; therefore the specifications and information contained in this document may change without notice. Eaton Corporation shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. -
Page 3: Introduction
GROUNDING / BONDING VIOLATION WILL with a maximum weight of ~3 lbs (~1.36 kg). SERIOUSLY AFFECT THE SPD’S ABILITY TO The Eaton RSPF Series is available in nine options, see FUNCTION AS SPECIFIED. Section 10, Ordering Guidelines for more details... -
Page 4: Rspf Series Catalog Number
IL158004EN Surge Protective Device 2 RSPF Series Catalog Number 4 Installation Each Eaton RSPF Series SPD is identified by a Catalog WARNING Number, see example in Table 1. The Catalog Number identifies the parameters that make up the unit. A LICENSED/QUALIFIED ELECTRICIAN MUST Table 1. -
Page 5: Warning
Connector Kit then discard/recycle the old panel. See Figure 2. Confirm that the system voltage is the same as the RSPF Series SPD that you are installing. Check the facility grounding system. All grounding, bonding, and earthing must meet the NEC, CEC and any other national, state and local electrical codes. - Page 6 SPD. See Figure 7. Figure 5. SPD installed – terminal side Figure 7. Apply label provided with SPD 11. The RSPF Series SPD’s Surge Ground Terminal 17. Replace the panelboard’s trim/door. can be wired to either the Ground Bar or the Neutral Bar whichever bar is closest to the SPD.
-
Page 7: Operation
RSPF Series Surge Protective Device IL158004EN Wiring Diagrams 5 Operation Power Up and System Checkout Switch main panel power to ON. The green LED should light to indicate the phase voltage is being monitored. If the red LED lights, remove power and contact the... -
Page 8: Specifications
DESCRIPTIONS CONTAINED HEREIN. Designed and tested in IEEE C62.41.1 accordance with the IEEE C62.41.2 In no event will Eaton be responsible to the purchaser or most recent version of IEEE C62.43 user in contract, in tort (including negligence), strict these standards: IEEE C62.45... -
Page 9: Ordering Guidelines
The following references are available at www.eaton.com Current Eaton Panelboards - Renewal Parts RP01400001E Eaton Renewal Parts Data - Panelboard Renewal Parts Supplement RP01414001E Vintage Cutler-Hammer panelboards and switchboards – Renewal Parts RP01400003E Vintage Westinghouse panelboards – Renewal Parts RP01400002E Rev. -
Page 10: Warranty
IL158004EN Surge Protective Device 11 Warranty Eaton warrants the RSPF Series SPD to be free from defects in both workmanship and materials for a period of 2 years from shipment. To register the product, go to www.eaton.com/RSP and click on the warranty registration icon. - Page 12 Eaton Corporation 1000 Cherrington Parkway Moon Township, PA 15108-4312 www.eaton.com/RSP © 2017 Eaton Corporation For additional information please call: All Rights Reserved Eaton’s Power Quality Technical Support Publication No. IL158004EN 1-800-809-2772 Option 4, sub-option 2 Rev. 2 – December 2017...
Need help?
Do you have a question about the RSPF Series and is the answer not in the manual?
Questions and answers