Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Kramer DigiTOOLS 7408
Summary of Contents for Kramer DigiTOOLS 7408
- Page 1 Kramer Electronics, Ltd. USER MANUAL Model: 7408 SDI to Analog Converter...
-
Page 2: Table Of Contents
Table 1: 7408 SDI to Analog Converter Table 2: Setting the Dipswitches Table 3: Dipswitch Settings (AUTO, PAL, and NTSC) Table 4: Technical specifications of the 7408 SDI to Analog Converter Table 5: Structure of the Protocol Table 6: Instruction Set for the 7408... - Page 3 1 For example: model number AD2512C, part number 2535-000251 – No operator-serviceable parts inside unit. – Use only the Kramer Electronics input power – Disconnect power and unplug unit from wall 2900-9999992...
-
Page 4: Introduction
Use Kramer high performance high resolution cables Overview The Kramer DigiTOOLS 7408 SDI to Analog Converter is a high quality, full 10-bit SDI to Analog video converter in a Kramer Tool housing. The 7408 SDI to Analog Converter is a multi-standard unit, converting 525-line SDI to NTSC or NTSC4.43, and 625-line SDI to PAL-B/D/G/H/I/N. -
Page 5: Your 7408 Sdi To Analog Converter
Kramer 7408 away from moisture, excessive sunlight and dust Your 7408 SDI to Analog Converter Figure 1 and Table 1 define the 7408 SDI to Analog Converter: Figure 1: 7408 SDI to Analog Converter Your 7408 SDI to Analog Converter... -
Page 6: Using Your 7408 Sdi To Analog Converter
5. Connect the 12V DC power adapter to the power socket and connect the adapter to the mains electricity. 1 Switch OFF the power on each device before connecting it to your 7408. After connecting your 7408, switch on its power and then switch on the power on each device... -
Page 7: Figure 2: Connecting A 7408 Sdi To Analog Converter
Using Your 7408 SDI to Analog Converter Warning: Do not cover the 7408 SDI Camera RS-232 Display Betacam Video Recorder Display Display Figure 2: Connecting a 7408 SDI to Analog Converter KRAMER: SIMPLE CREATIVE TECHNOLOGY... -
Page 8: Connecting A Pc
Using Your 7408 SDI to Analog Converter 5.2 Connecting a PC To connect a PC to the 7408 unit, using the Null-modem adapter provided with the machine (recommended): Connect the RS-232 DB9 rear panel port on the 7408 unit to the... -
Page 9: Setting The Dipswitches
Using Your 7408 SDI to Analog Converter 5.3 Setting the Dipswitches Configure the 7408 unit by setting the dipswitches, as Table 2 defines: DIPS Function PROGRAM ON for upgrading firmware; otherwise OFF ON to enable Vertical Interval Blanking; OFF to disable PEDESTAL ON for pedestal (7.5 IRE offset selection for NTSC);... -
Page 10: Technical Specifications
ACCESSORIES: 1 Specifications are subject to change without notice Technical Specifications of the 7408 SDI to Analog Converter 1 SDI: SMPTE-259M, ITU-R BT.601 on a BNC connector 1 reclocked SDI: SMPTE-259M, ITU-R BT.601 on a BNC connector 1 composite video: 1Vpp / 75 on a BNC connector 1 s-Video: 1Vpp, 0.3Vpp / 75 on two BNC connectors... -
Page 11: Communication Protocol
Communication Protocol RS-232 communication between the 7408 and the PC is done using the following protocol. The protocol uses four bytes of information, and data is at 9600 baud, no parity, 8 data bits and 1 stop bit. The controller and machine should be connected via a null-modem... - Page 12 Note that the video parameter values range from 0 (minimum) up to 255dec (maximum), and do not necessarily correspond with the number displayed on the panel of the 7408. If a value outside the legal range of a particular parameter is sent, the error code will be returned.
- Page 13 3 = PAL-N 64dec (40hex)= Invalid or no input detected Note that when the DIP-switches are set for a fixed standard, the 7408 will reply by sending the code for the fixed standard. INSTRUCTION 16dec – ERROR If the machine receives an invalid instruction, it replies by sending this error code.
- Page 14 EXCLUSION OF DAMAGES The liability of Kramer for any effective products is limited to the repair or replacement of the product at our option. Kramer shall not be liable for: Damage to other property caused by defects in this product, damages based upon inconvenience, loss of use of the product, loss of time, commercial loss;...
- Page 15 For the latest information on our products and a list of Kramer distributors, visit our Web site: www.kramerelectronics.com, where updates to this user manual may be found. We welcome your questions, comments and feedback. Kramer Electronics, Ltd. Web site: www.kramerelectronics.com E-mail: info@kramerel.com...
Need help?
Do you have a question about the DigiTOOLS 7408 and is the answer not in the manual?
Questions and answers