Table of Contents
Advertisement
Quick Links
MODEL # SSD
Prior to assembly, you will need the following tools:
7/16" Wrench or adjustable wrench
Needle nose pliers
Grease gun
TheAndersons_PSSD-AN_ Manual_0720-2
Professional Drop Spreader
ASSEMBLY INSTRUCTIONS
THANK YOU
You have purchased the highest quality professional
broadcast spreader available on the market today. The
SSD is the accumulation of proven performance and will
provide you with years of trouble-free service. In the
event you should have any questions or comments,
please call our professional support staff.
BEFORE YOU BEGIN
To assemble your new spreader, we highly recommend
that you read all the instructions thoroughly, familiarize
yourself with the assembly and components, and verify
that all parts are included in the package.
Our toll-free number is 1-800-225-2639 (U.S. Only).
IN THE BOX
(1) Upper handle and control assembly
(1) Hopper assembly
(2) Tires
(1) Hopper handle
(2) Hardware Pack
(1) Rain cover
•
The hardware pack (P142424)
includes the following:
(2) 3/16-1/4" x 1" Cotter pin-bow tie SS
(2) 3/16" x 2" Cotter pin
(4) ¼-20 x 1-1/2" HHCS SS
(4) ¼-20 nylon locknut SS
(1) Gauge calibration
(2) ¼-20 x 5/8 Bolt SS
PAGE 1
Advertisement
Table of Contents
Related Manuals for The Andersons SSD
Summary of Contents for The Andersons SSD
- Page 1 You have purchased the highest quality professional broadcast spreader available on the market today. The SSD is the accumulation of proven performance and will provide you with years of trouble-free service. In the event you should have any questions or comments, please call our professional support staff.
-
Page 2: Assembly Steps
Assembly and Operation Instructions Assembly Steps Remove spreader and components from Step 1: carton. Slide Wheels onto each end of Axle with the Step 2: longer portion of the Wheel hub facing the Hopper. Secure Wheels with 3/16 dia. x 2” Cotter Pins. Stand spreader upright on Wheels. - Page 3 Assembly and Operation Instructions Slide the ends of the Control Tube Braces over Step 4: the Studs on the Shutoff Bar Brackets, secure with Cotter Pins. Install Hopper Handle on front of spreader using (2) 1/4-20 x 1/2” Hex Bolts and Locknuts. To check spreader for completed shutoff, pull Step 5: the Handle Lever back to the “OFF”...
-
Page 4: Operation
Assembly and Operation Instructions Operation Before filling Hopper, make sure spreader Step 1: Handle Lever is in the “OFF” position. Always fill spreader on walk or drive, not on the lawn. Loosen Rate Control Knobs and move the Tie Step 2: Bar to setting recommended for the product applied. - Page 5 Assembly and Operation Instructions Determining Application Rates The following procedure provides a means of accurately determining drop spreader settings when settings do not appear on the package, or to “fine tune” the manufacturer’s recommend settings. Spreader rates can vary due to walking speed, condition of turf, humidity, physical characteristics of the product being applied, or condition of the spreader.
- Page 6 Assembly and Operation Instructions How to Verify Spreader Calibration Loosen both rate control knobs and set spreader setting at #4 1/2. With the operating lever in the open Step 1: position, turn spreader upside down. Place accuracy gauge in position as shown above with notch facing away from shut off bar. Check openings Step 2: near the ends and in the middle of the spreader.
-
Page 7: Maintenance
Assembly and Operation Instructions Maintenance Never store material in spreader. Return unused product to its original container. Step 1: Set Rate Slide on the highest number, open spreader, and spin Wheels to remove excess material. Step 2: Wash out Hopper thoroughly after each use to remove material clinging to surfaces. Pay close attention to Step 3: area between the Shutoff Bar and Hopper. - Page 8 Assembly and Operation Instructions Parts Diagram–LCO-1000 TheAndersons_PSSD-AN_ Manual_0720-2 PAGE 8...
-
Page 9: How To Order Spare Parts
HOW TO ORDER SPARE PARTS See diagram for assistance in identifying specific parts. For parts orders, call 1-574-848-7491. (Note: Sales of parts for the Andersons spreaders are handled by Earthway, Inc.) IMPORTANT: When ordering replacement parts, always provide the following information: ... -
Page 10: Customer Service
This warranty does not extend to any Product or parts thereof that have been allowed to corrode, subjected to misuse, neglect, accident, or modification by anyone other than The Andersons or that have been affixed to any nonstandard accessory attachment or that have been used, stored, installed, maintained operated in violation of The Andersons instructions or standard industry practice.