HID Signo 25B Install Manual page 2

Optional features Optional features
Open Collector Output – Controls an external device (5 VDC) operating in Host Mode only. Sink 40 mA / Open Collector Output – Controls an external device (5 VDC) operating in Host Mode only. Sink 40 mA /
Source -1 mA. Source -1 mA.
Optical Tamper – If connected via the pigtail wires, the optical tamper will sink to ground from the default of Optical Tamper – If connected via the pigtail wires, the optical tamper will sink to ground from the default of
5 VDC when the reader is removed from its backplate. 5 VDC when the reader is removed from its backplate.
Relay Output – Typically used to control a strike lock. Three contacts are available on the pigtail wires Relay Output – Typically used to control a strike lock. Three contacts are available on the pigtail wires
(common, normally open, and normally closed). (common, normally open, and normally closed).
Wiegand Reader Interface – There is Wiegand output available, as marked on the pigtail wires. Wiegand Reader Interface – There is Wiegand output available, as marked on the pigtail wires.
Configuration options are available within HID Biometric Manager™. Configuration options are available within HID Biometric Manager™.
Specifications Specifications
Input Voltage (V DC) Input Voltage (V DC)
12V DC 12V DC
Standby Current AVG Standby Current AVG 800 mA 800 mA
1 1
Max Current AVG Max Current AVG 1.5 A 1.5 A
2 2
Peak Current Peak Current 2 A 2 A
3 3
Operating Temperature Operating Temperature -4° F to 150° F (-20° C to 66° C) -4° F to 150° F (-20° C to 66° C)
Standby AVG - Root Mean Square current draw without a card in the RF field. Standby AVG - Root Mean Square current draw without a card in the RF field.
1 1
Maximum AVG - Root Mean Square current draw during continuous card reads. Not evaluated by UL. Maximum AVG - Root Mean Square current draw during continuous card reads. Not evaluated by UL.
2 2
Peak - highest instantaneous current draw during RF communication. Peak - highest instantaneous current draw during RF communication.
3 3
Regulatory Regulatory
UL UL
Connect only to a Listed Access Control / Burglary LPS power supply. These readers are intended to be Connect only to a Listed Access Control / Burglary LPS power supply. These readers are intended to be
used with listed (UL294) control equipment. Suitable for outdoor use. used with listed (UL294) control equipment. Suitable for outdoor use.
Only Wiegand and Bluetooth communications have been evaluated by UL. Only Wiegand and Bluetooth communications have been evaluated by UL.
The Open Collector Output has not been evaluated by UL. The Open Collector Output has not been evaluated by UL.
RS485 communications has not been evaluated by UL. RS485 communications has not been evaluated by UL.
Inputs (reserved for future use) have not been evaluated by UL. Inputs (reserved for future use) have not been evaluated by UL.
The Ethernet connection is for supplemental use; the unit is connected to an Access Control Panel. The Ethernet connection is for supplemental use; the unit is connected to an Access Control Panel.
The Signo 25B Biometric Reader is compatible with HID Mobile Access® version 3.3.1 and later using The Signo 25B Biometric Reader is compatible with HID Mobile Access® version 3.3.1 and later using
mobile devices with BLE version 4.2 and later listed at: mobile devices with BLE version 4.2 and later listed at:
https://www.hidglobal.com/mobile-access-compatible-devices https://www.hidglobal.com/mobile-access-compatible-devices
Install in accordance with NFPA70 (NEC) Local Codes, Canadian Electrical Code CSA 22.1, and authorities Install in accordance with NFPA70 (NEC) Local Codes, Canadian Electrical Code CSA 22.1, and authorities
having jurisdiction. Follow all National and Local Codes. having jurisdiction. Follow all National and Local Codes.
UL 294 Performance Levels UL 294 Performance Levels
Access Control Access Control
Model # Model #
Line Security Level Line Security Level
25B 25B Level I Level I
CE Marking CE Marking
HID Global hereby declares that these proximity readers are in compliance with the essential requirements HID Global hereby declares that these proximity readers are in compliance with the essential requirements
and other relevant provisions of Directive 2014/53/EU. and other relevant provisions of Directive 2014/53/EU.
Por el presente, HID Global declara que estos lectores de proximidad cumplen con los requisitos esenciales Por el presente, HID Global declara que estos lectores de proximidad cumplen con los requisitos esenciales
y otras disposiciones relevantes de la Directiva 2014/53/EU. y otras disposiciones relevantes de la Directiva 2014/53/EU.
HID Global déclare par la présente que ces lecteurs à proximité sont conformes aux exigences essentielles HID Global déclare par la présente que ces lecteurs à proximité sont conformes aux exigences essentielles
et aux autres stipulations pertinentes de la Directive 2014/53/EU. et aux autres stipulations pertinentes de la Directive 2014/53/EU.
A HID Global, por meio deste, declara que estes leitores de proximidade estão em conformidade com as A HID Global, por meio deste, declara que estes leitores de proximidade estão em conformidade com as
exigências essenciais e outras condições da diretiva 2014/53/EU. exigências essenciais e outras condições da diretiva 2014/53/EU.
HID Global bestätigt hiermit, dass die Leser die wesentlichen Anforderungen und anderen relevanten HID Global bestätigt hiermit, dass die Leser die wesentlichen Anforderungen und anderen relevanten
Bestimmungen der Richtlinie 2014/53/EU erfüllen. Bestimmungen der Richtlinie 2014/53/EU erfüllen.
HID Global dichiara che i lettori di prossimità sono conformi ai requisiti essenziali e ad altre misure rilevanti HID Global dichiara che i lettori di prossimità sono conformi ai requisiti essenziali e ad altre misure rilevanti
come previsto dalla Direttiva europea 2014/53/EU. come previsto dalla Direttiva europea 2014/53/EU.
Download copies of the Radio Equipment Directive Declaration of Conformity (DoC) at: Download copies of the Radio Equipment Directive Declaration of Conformity (DoC) at:
http://www.hidglobal.com/certifications http://www.hidglobal.com/certifications
Russia Russia
Дата изготовления указана на маркировке оборудования Дата изготовления указана на маркировке оборудования
Представитель в Российской Федерации Представитель в Российской Федерации
Название Название ООО «Дофин» ООО «Дофин»
Адрес Адрес 140573, РФ, Московская обл., Озерский район, с. Бояркино 140573, РФ, Московская обл., Озерский район, с. Бояркино
Контактное лицо Контактное лицо Л.Н. Голубова Л.Н. Голубова
Телефон Телефон +7 495 223 6008 +7 495 223 6008
e-mail e-mail local.declarant@gmail.com local.declarant@gmail.com
Israel Israel
‫.יטוחלא הלעפה ןוישרמ רוטפ חוקלה ,דבלב חוקלה לש ימצע שומישל ״קזב תלועפב״ קר‬ ‫.יטוחלא הלעפה ןוישרמ רוטפ חוקלה ,דבלב חוקלה לש ימצע שומישל ״קזב תלועפב״ קר‬
‫.רחא ינכט יוניש לכ וב תושעל אלו ,רישכמה לש תירוקמה הנטנאה תא ףילחהל רוסא‬ ‫.רחא ינכט יוניש לכ וב תושעל אלו ,רישכמה לש תירוקמה הנטנאה תא ףילחהל רוסא‬
Destructive Destructive Endurance Endurance Stand-By Stand-By
Attack Level Attack Level Level Level Power Level Power Level
Level I Level I Level IV Level IV Level I Level I
‫.יטוחלא הלעפה ןוישרמ רוטפו ״ינשמ״ סיסב לע וניה רישכמב שומישה‬ ‫.יטוחלא הלעפה ןוישרמ רוטפו ״ינשמ״ סיסב לע וניה רישכמב שומישה‬
E4662 E4662
Canada Radio Certification Canada Radio Certification
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device. interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts
de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire
de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement. brouillage est susceptible d'en compromettre le fonctionnement.
FCC FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference (1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. received, including interference that may cause undesired operation.
CAUTION: Any changes or modifications to this device not explicitly approved by the manufacturer could CAUTION: Any changes or modifications to this device not explicitly approved by the manufacturer could
void your authority to operate this equipment. void your authority to operate this equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures: one or more of the following measures:
• Reorient or relocate the receiving antenna. • Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver. • Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. • Consult the dealer or an experienced radio/TV technician for help.
Taiwan Taiwan
根據NCC低功率電波輻射性電機管理辦法 規定: 根據NCC低功率電波輻射性電機管理辦法 規定:
第十二條 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻
率、加大功率或變更原設計之特性及功能。 率、加大功率或變更原設計之特性及功能。
第十四條 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立
即停用，並改善至無干擾時方得繼續使用。 即停用，並改善至無干擾時方得繼續使用。
前項合法通信，指依電信法規定作業之無線電通信。 前項合法通信，指依電信法規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
Korean KCC Korean KCC
항목 항목
송신주파수 송신주파수
수신주파수 수신주파수
출력 출력 RFID: 10m에서 47.544mv이하 RFID: 10m에서 47.544mv이하
Conditions Conditions 전원 전원
전파형식 전파형식
발진방식 발진방식
변조방식 변조방식
Singapore Singapore
Complies with Complies with
IMDA Standards IMDA Standards
DA103548 DA103548
South Africa South Africa
Brazil Brazil
Compliance Statement Compliance Statement
Este produto está homologado pela ANATEL, de acordo com os procedimentos regulamentados pela Este produto está homologado pela ANATEL, de acordo com os procedimentos regulamentados pela
Resolução 242/2000, e atende aos requisitos técnicos aplicados. Para maiores informações, consulte o site Resolução 242/2000, e atende aos requisitos técnicos aplicados. Para maiores informações, consulte o site
da ANATEL - www.anatel.gov.br da ANATEL - www.anatel.gov.br
This product is homologated at ANATEL according to procedure regulated by Resolution 242/2000, and it This product is homologated at ANATEL according to procedure regulated by Resolution 242/2000, and it
complies with the applicable technical requirements. For more information, consult ANATEL website - www. complies with the applicable technical requirements. For more information, consult ANATEL website - www.
anatel.gov.br anatel.gov.br
RF Warning Statement RF Warning Statement
Per Article 6 of Resolution 506, equipment of restricted radiation must carry the following statement in a Per Article 6 of Resolution 506, equipment of restricted radiation must carry the following statement in a
visible location: visible location:
Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência
prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em
caráter primário. caráter primário.
This equipment operates in secondary character, meaning it does not have the right of protection against This equipment operates in secondary character, meaning it does not have the right of protection against
harmful interference, even against those the same character, and it cannot cause any interference to harmful interference, even against those the same character, and it cannot cause any interference to
systems operating in the primary character. systems operating in the primary character.
15 15
Equipment Equipment
8T2 9 8T2 9
ACC Control READER ACC Control READER
© 2022 HID Global Corporation/ASSA ABLOY AB. © 2022 HID Global Corporation/ASSA ABLOY AB.
All rights reserved. All rights reserved.
PLT-04026, Rev. B.3 PLT-04026, Rev. B.3
hidglobal.com hidglobal.com
Part of ASSA ABLOY Part of ASSA ABLOY
For technical support, please visit: https://support.hidglobal.com For technical support, please visit: https://support.hidglobal.com
25B 25B
규격 규격
RFID:13.56 MHz RFID:13.56 MHz
RFID:13.56 MHz RFID:13.56 MHz
DC 12.0V DC 12.0V
A1D A1D
X-tal X-tal
RFID: ASK, NFC: GFSK RFID: ASK, NFC: GFSK
UAE UAE Australia and New Zealand Australia and New Zealand
TRA TRA
REGISTERED NO: REGISTERED NO:
ER72356/19 ER72356/19
DEALER NO: DEALER NO:
E4662 E4662
DA37204/14 DA37204/14
TA-2019/920 TA-2019/920
APPROVED APPROVED
General Signaling General Signaling
Equipment Equipment
ABCD12345678 ABCD12345678 CIDF18000157 CIDF18000157