HID Vertx CS V100 Quick Installation Manual
  1. Manuals
  2. Brands
  3. HID Manuals
  4. Controller
  5. Vertx CS V100
  6. Quick installation manual

HID Vertx CS V100 Quick Installation Manual

Hide thumbs

Advertisement

Table of Contents

9292 Jeronimo Road
Irvine, CA 92618-1905
PROPRIETARY INFORMATION. This document contains proprietary information which may not be duplicated,
published or disclosed to others, or used for any purpose without written permission from HID Corporation. 2004
© HID Corporation. All rights reserved.
Quick Installation Guide
V100 DOOR/READER INTERFACE
Document Version 1.1
August 4, 2005
Document Number 6080-907B

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Vertx CS V100 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for HID Vertx CS V100

Summary of Contents for HID Vertx CS V100

  • Page 1: Quick Start, Vertx (Cs) V100 Door/Reader Interface Panel

    V100 DOOR/READER INTERFACE PROPRIETARY INFORMATION. This document contains proprietary information which may not be duplicated, published or disclosed to others, or used for any purpose without written permission from HID Corporation. 2004 © HID Corporation. All rights reserved. Document Version 1.1...

  • Page 2: Table Of Contents

    What you need before getting started ..............4 V100 ........................4 Step 2 Hardware Installation ...................... 5 Mounting Instructions .................... 5 Wiring VertX ......................5 Contact Information ........................8 August 2005 Page 2 of 9 2005 © HID Corporation. All rights reserved.

  • Page 3: Introduction

    Fewer conductors needed if all control lines are not used. Power Supply ---- Refer to your Power Supply Installation Guide. +12 VDC IN * Minimum wire gauge depends on cable length and current requirements. August 2005 Page 3 of 9 2005 © HID Corporation. All rights reserved.

  • Page 4: Overview

    2. If the V100 is being installed as part of an array, or in a third party enclosure, follow the directions provided by the Integrator or Dealer. Terminating Jumper August 2005 Page 4 of 9 2005 © HID Corporation. All rights reserved.

  • Page 5: Step 2 Hardware Installation

    Red LED 12VDC. Data Return Green LED Green LED Data Return Red LED Data 1 / Clock Beeper Data 0 / Data Hold Ground Shield Ground Reader Power August 2005 Page 5 of 9 2005 © HID Corporation. All rights reserved.
  • Page 6 4. Interface Address – Set the interface address by turning the Address dial. Ensure that the V100 Interface Address is documented in the Hardware Installation Worksheet (found in the back of the HID VertX V1000 Quick Install guide). 5. Output Connections – All Output connections are used for general purpose controls.
  • Page 7 Any input can be configured as a supervised input. They can be configured for resistor values of 1K – 6K Ohm. The setup of supervised inputs should be done during configuration of the VertX units via the central station automation software (host) or using the Calibrate Input tool explained in the HID VertX V1000 Quick Installation guide.

  • Page 8: Contact Information

    Batt Fail Contact Information 929274 Jeronimo Road, Irvine, CA 92618-1905 HID Corporation Web Site http://www.hidcorp.com Main Phone (949) 598-1600 (949) 598-1698 Sales (800) 210-4744 Technical Support (800) 237-7769 August 2005 Page 8 of 9 2005 © HID Corporation. All rights reserved.
  • Page 9 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. August 2005 Page 9 of 9 2005 © HID Corporation. All rights reserved.

Table of Contents