HID Signo 25B User Manual
Hide thumbs
Also See for Signo 25B:
- Installation manual (2 pages) ,
- Installation manual (35 pages) ,
- Install manual (2 pages)
Related Manuals for HID Signo 25B
Summary of Contents for HID Signo 25B
- Page 1 HID® Signo™ Biometric Reader 25B User Guide PLT-04900, B.1 March 2021 HID® Signo™ Biometric Reader 25B User Guide Powering Trusted Identities...
- Page 2 HID Global Corporation. Trademarks HID GLOBAL, HID, the HID Brick logo, the Chain Design, iCLASS SE, HID Signo, Seos, HID Reader Manager, and HID Biometric Manager are trademarks or registered trademarks of HID Global, ASSA ABLOY AB, or its affiliate(s) in the US and other countries and may not be used without permission.
-
Page 3: Table Of Contents
1.3.2 Network connection 1.3.3 Standalone operating mode connections 1.3.4 Direct connection to PC 1.4 Hardware reset the Signo 25B Fingerprint enrollment guidelines 2.1 General guidelines 2.2 Fingerprint enrollment best practices for Signo 25B Acronyms and terminology PLT-04900, B.1 March 2021... -
Page 4: Overview
Section 01 Overview Powering Trusted Identities... -
Page 5: Hardware Specifications
This section provides the HID® Signo™ Biometric Reader 25B wiring functions and color codes, together with system connection options. HID Global is bringing the iCLASS SE® Signo 25B into the Signo™ family of readers and rebranding it as the HID Signo Biometric Reader 25B. -
Page 6: Wiring Function And Color Codes
The following shows Signo 25B wiring functions and color codes. Important: Bond the ground wires between the Signo 25B power supply and the panel power supply. Important: The 19 pigtail wires should be cut to size for wall mounted installations. DO NOT cut the Ethernet cable. -
Page 7: System Connections
Note: It is best practice to use separate power supplies for the Signo 25B and the electric locks. 1.3.2 Network connection Network connection to a network that has a server or a router configured for DHCP. -
Page 8: Standalone Operating Mode Connections
Direct connection to PC using an auto assigned IP address or a static IP address. Note: It can take up to five minutes for this connection type to configure. Note: Supported network installations can be found in the HID Biometric Manager Administration Guide (PLT-04029). -
Page 9: Hardware Reset The Signo 25B
4. With power supplied to the reader, short the contacts together using a suitable metal object. 5. Maintain the short for a full five seconds. The Signo 25B will beep while you hold the short. 6. One long beep of two seconds confirms the reset. All device settings will be returned to the default. -
Page 10: Fingerprint Enrollment Guidelines
Section 02 Fingerprint enrollment guidelines Powering Trusted Identities... -
Page 11: General Guidelines
Trusted Identities User Guide The HID® Signo™ Biometric Reader 25B is capable of extracting quality features even from fingers with poor conditions. Nevertheless, correct placement of fingers on the sensor during enrollment helps consistency in fingerprint recognition. Adhere to the following general guidelines and Signo 25B specific guidelines to enroll optimal fingerprint images from a user’s finger to improve recognition performance. -
Page 12: Fingerprint Enrollment Best Practices For Signo 25B
Contact the administrator as you may need to enroll another finger fingerprint pattern 2.2 Fingerprint enrollment best practices for Signo 25B 1. Insert your finger into the Signo 25B sensor area so the finger tip touches the back wall and rests softly on the sensor slope. PLT-04900, B.1... - Page 13 Powering HID® Signo™ Biometric Reader 25B Trusted Identities User Guide 2. Slide your finger down so that it completely covers the sensor window contact surface. 3. Apply gentle pressure on the sensor to slightly flatten your finger and expose a maximum usable area.
-
Page 14: Acronyms And Terminology
Section 03 Acronyms and terminology Powering Trusted Identities... - Page 15 Device (ToD). The sensor is not armed (blue light off) until the Credential is presented. Finger Only: The Signo 25B is waiting for a finger to be presented that is stored in its local device database. If the presented finger matches one stored in the database a Grant Access is recommended.
- Page 16 Powering HID® Signo™ Biometric Reader 25B Trusted Identities User Guide Term Definition MINEX Minutia Interoperability Exchange. The MINEX program is dedicated to the evaluation and development of the capabilities of fingerprint minutia matchers running on ISO/IEC 7816 smart cards. M-Series Mercury Platform Series of Products.
- Page 17 Powering HID® Signo™ Biometric Reader 25B Trusted Identities User Guide Revision history Date Description Revision March 2021 Product rebrand from iCLASS SE® Signo 25B to HID Signo® Biometric Reader 25B June 2020 Initial release. PLT-04900, B.1 March 2021...
- Page 18 Dummy text. Powering Trusted Identities PLT-04900, B.1 Americas & Corporate Asia Pacific Europe, Middle East & Africa Brazil 611 Center Ridge Drive 19/F 625 King's Road 3 Cae Gwyrdd Condomínio Business Center Austin, TX 78758 North Point Green Meadow Springs Av.