Advertisement
Quick Links
2500 series
Magnetic Drive, Seal-less Chemical Pumps
O P E R A T I O N
M A N U A L
END SUCTION AND SELF PRIMING MODELS
SELF PRIMING
• PMSP-2505
• KMSP-2505
• PMSP-2510
• KMSP-2510
• PMSP-2525
• KMSP-2525
• PMSP-2550
• KMSP-2550
END SUCTION
• PM-2505
• KM-2505
• PM-2510
• KM-2510
• PM-2525
• KM-2525
• PM-2550
• KM-2550
Advertisement
Related Manuals for Ceco Sethco 2500 Series
Summary of Contents for Ceco Sethco 2500 Series
- Page 1 2500 series Magnetic Drive, Seal-less Chemical Pumps O P E R A T I O N M A N U A L END SUCTION AND SELF PRIMING MODELS SELF PRIMING • PMSP-2505 • KMSP-2505 • PMSP-2510 • KMSP-2510 • PMSP-2525 •...
- Page 2 SAFETY RULES FOR SETHCO PUMPS 700 Emlen Way • Telford, PA 18969 Phone: 215.723.8155 Email: infofhs@onececo.com www.cecoenviro.com CONGRATULATIONS! You have just purchased a Sethco Pump, a quality industrial product manufactured to exacting standards. To insure prolonged life of your purchase, please take a few minutes to review the operating instructions and become familiar with the pump.
-
Page 3: Terms And Conditions Of Sale
700 Emlen Way • Telford, PA 18969 Phone: 215.723.8155 Email: infofhs@onececo.com www.cecoenviro.com TERMS AND CONDITIONS OF SALE any kind, and the buyer, by accept- The terms and conditions stated acceptance by Sethco cannot be canceled without Sethco's written ance of such equipment, assumes below and on the face of any Met consent, and then only upon pay- all liability for the consequences of... -
Page 4: High Volume
PD-340-03 HIGH VOLUME END SUCTION MAGNETIC DRIVE SEAL-LESS PUMP 700 Emlen Way • Telford, PA 18969 PARTS LIST Phone: 215.723.8155 OPERATION INSTRUCTIONS Email: infofhs@onececo.com www.cecoenviro.com June 1, 2002 For high volume transfer of most acids, alkalies, caustics, bleaches, sea water, solvents and many other harsh environments WARNING: PUMP CONTAINS POWERFUL... -
Page 5: Troubleshooting
O P E R A T I N G I N S T R U C T I O N S YOU WILL NEED THE FOLLOWING TOOLS specific gravity liquids, the pump cannot start 1. 3/8" ratchet pumping with an open discharge line. To over 2. -
Page 6: Parts List
P A R T S L I S T 17, 21, 22, 23 15, 16 17, 20, 22 4.5" Impeller Bearing POLYPROPYLENE MODELS KYNAR MODELS ITEM DESCRIPTION QTY. MATERIAL PART NUMBER MATERIAL PART NUMBER MOTOR VARIOUS CONSULT FACTORY VARIOUS CONSULT FACTORY Adapter Plate Noryl 010P400355-513... - Page 7 ASSEMBLY: WET END SUBASSEMBLY 1. Lay cup (8) flat on table. Open end up. Install nuts into hex area found in back of adapter plate. 2. Insert pin (19) into shaft (14) (unless pin is pre-molded in Torque bolts to 10 ft./lbs. shaft).
- Page 8 IMPORTANT! With pump standing on fan end of motor, 6. Lift the casing (6) off the cup vertically. Make sure that insert a long screw driver and use it to spin the impeller to the washer (11) is not damaged. Set casing (6) and make sure it spins freely..
- Page 9 FIGURE 5 FIGURE 6 FIGURE 8 FIGURE 7 FIGURE 9 FIGURE 10...
- Page 10 FIGURE 11 FIGURE 12 MOTOR FEET BOTTOM FLAT BOSS 1/16” ADAPTER MAGNET BELOW ADAPTER FIGURE 13 FIGURE 14 FIGURE 17 FIGURE 15 FIGURE 16...
- Page 11 PD-345-02 HIGH VOLUME SELF PRIMING MAGNETIC-DRIVE SEAL-LESS PUMP 700 Emlen Way • Telford, PA 18969 PARTS LIST Phone: 215.723.8155 Email: infofhs@onececo.com OPERATION INSTRUCTIONS www.cecoenviro.com June 1, 2002 For high volume transfer of most acids, alkalies, caustics, bleaches, sea water, solvents and many other harsh environments WARNING: PUMP CONTAINS POWERFUL...
- Page 12 O P E R A T I N G I N S T R U C T I O N S YOU WILL NEED THE FOLLOWING TOOLS 2. Turn switch "on" and then "off" immediately. Observe 1. 3/8" ratchet rotation. It should be in the direction of the arrow on 2.
- Page 13 P A R T S L I S T DISCHARGE WARNING INLET PUMP CONTAINS POWERFUL MAGNETS. EXTREME CARE MUST BE USED DURING ASSEMBLY AND DISASSEMBLY 17, 21, 22, 23 TO AVOID INJURY. 19 26 33 17" 14.5" 3 HP - 10-3/4" 15,16 5 3 14 7 6 13...
- Page 14 IMPELLER MODEL # ASSEMBLY BEARING MATERIAL IMPELLER MATERIAL MODEL CARBON SILICONE CARBIDE Torque Specs 2510 CONSULT FACTORY CONSULT FACTORY POLYPRO 2525 CONSULT FACTORY CONSULT FACTORY Casting - Cup 10 ft. lbs. 2550 CONSULT FACTORY CONSULT FACTORY Adapter - Plate 10 ft. lbs. 2510 CONSULT FACTORY CONSULT FACTORY...
- Page 15 6. You will notice that the disk (7) has centered itself with 10 ft./lbs. the magnets. As you lower the assembly, you will need to 14. Connect plumbing to pump. Remove inlet priming make sure the disk seats into the counter bore in the chamber cover (31) to add fluid.
- Page 16 FIGURE 2 FIGURE 1 HOLE HOLE FIGURE 3 FIGURE 4 FIGURE 5 FIGURE 6...
- Page 17 FIGURE 8 FIGURE 7 FIGURE 10 FIGURE 9 FIGURE 12 FIGURE 11 MOTOR FEET BOTTOM FLAT BOSS...
- Page 18 1/16” ADAPTER MAGNET BELOW ADAPTER FIGURE 13 FIGURE 14 FIGURE 16 FIGURE 15 FIGURE 18 FIGURE 17...
- Page 19 FIGURE 19 FIGURE 20 FIGURE 22 FIGURE 21 FIGURE 23 FIGURE 24...
- Page 20 FIGURE 25 FIGURE 26 FIGURE 27 FIGURE 28...