Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ceco Fybroc 8500 Series
Summary of Contents for Ceco Fybroc 8500 Series
- Page 1 Fybroc ® Series 8500 Vertical Turbine Pumps I N S T T I O N M...
-
Page 2: Table Of Contents
INDEX Page Page Fybroc Warranty..........1 Piping the Pump..........5 General Description..........2 Starting the Pump..........5 Pre-Installation............2 Troubleshooting Checklist........ 6 Installation............2 Maintenance............. 6 Foundation............3 Disassembly............6 Pump Installation..........3 Reassembly............7 Impeller Adjustment..........4 Typical Exploded View Drawing....... 8 Mechanical Seal Adjustment......4 Typical Sectional Drawing...... -
Page 3: Fybroc Warranty
All illustrations and provisions in specifications are descriptive and are not intended as warranties. Penalty of any kind are not acceptable unless approved in writing by an officer of CECO Environmental Corporation. -
Page 4: General Description
general descriptiOn Ensure that proper electrical service is available for the motor, per motor name plate. Fybroc Vertical Turbine Pumps (Series 8500) are ® Check the depth, diameter and straightness centrifugal, diffuser type, single or multi-stage, wet of the sump against the pump dimensions to pit type pumps for installation in a pit, well or a tank. -
Page 5: Foundation
Once the pump has been lifted, and prior to FOundatiOn lowering it into the pit, install the flush line to the The foundation should be level, providing rigid support lower (suction bell) bearing. Also, if applicable, for the pump and motor. It should also be of sufficient install the basket strainer. -
Page 6: Impeller Adjustment
impeller adJustment – all mOdels 7) Turn the coupling by hand. THE SHAFT SHOULD TURN FREELY WITH MINIMAL TORQUE. SOME The impeller adjustment on all models is accomplished SLIGHT RUBBING MAY BE NORMAL WITH A through the coupling. NEW PUMP BUT THERE SHOULD BE NO SIGNIFICANT BINDING. -
Page 7: Piping The Pump
TROUBLESHOOTING pump prOBlem prOBaBle cause sOlutiOn Pump does not run 1. Motor issues 1. Evaluate motor components. a. Incorrect connections a. Check wiring diagram on motor and starter. b. Incorrect control box b. Check specifications for HP, voltage, c. Low voltage frequency. -
Page 8: Troubleshooting Checklist
14) The pump end with the shaft can be removed periOdic maintenance completely and set aside where it is more convenient Periodically check the flush line from the to work. (Depending on the length of the pump, it may mechanical seal. There should be a continuous, not be possible or convenient to pull out the entire light stream of liquid flowing out of the mechanical shaft. -
Page 9: Reassembly
FYBROC SERIES 8500 – P RTS ND ST ND RD M TERI LS OF CONSTRUCTION 89B 89C 131B 131A 17C 17D 17E 70B 70C 81B 81C 81D 81B 81C 81D 93F 93G 93H... -
Page 10: Typical Exploded View Drawing
Item Number escription Standard Material Item Number escription Standard Material Bowl (Discharge) VR-1 Gasket, Lower Pedestal Viton Bowl (Intermediate) VR-1 Strainer Basket VR-1 Bolt, Bowl 316 SS Screw, Strainer 316 SS Flat Washer, Bowl 316 SS Single Cartridge Seal Assembly O-Ring, Bowl Viton Bolt, Mechanical Seal... - Page 11 FYBROC SERIES 8500 – TYPIC L SECTION L DETAIL A SCALE 1:8 DETAIL B SCALE 1:8 DETAIL C SCALE 1:8...
-
Page 12: Typical Sectional Drawing
FYBROC SERIES 8500 – PUMP DIMENSIONS VIEW A-A MOTOR: VERTICAL SCALE 1:10 SOLID SHAFT HIGH A (APPROX.) THRUST – “P” BASE RIGID COUPLING MECHANICAL SEAL (F)" DISCHARGE COUPLING GUARD FLANGE 150 LB. FLAT PRODUCT FLUSH FACE (DIN RETURN FROM Ø 7/8" [22] PN 10/16 MECHANICAL SEAL THRU HOLES... -
Page 13: Typical Outline Drawing
nOtes... -
Page 14: Notes
nOtes... - Page 15 nOtes...
- Page 16 ® IS COPYRIGHT 2017 CECO ENVIRONMENT L CORPOR TION FY ROC REGISTERED TR DEM RK OF CECO ENVIRONMENT L CORPOR TION. 07-5326 114 AALSO 700 Emlen Way • Telford, P 18969 AUGUST 2017 P: 215.723.8155 • TOLL-FREE: 800.FYBROC.1 • F: 215.723.2197...