Table of Contents
Advertisement
5.3
Rotary Actuator Installation (Continued)
5.3
Rotary Actuator Installation (Continued)
5.3
Rotary Actuator Installation (Continued)
5.3.1
Mounting the Rotary NAMUR Bracket to the Actuator
5.3.1
Mounting the Rotary NAMUR Bracket to the Actuator
5.3.1
Mounting the Rotary NAMUR Bracket to the Actuator
1 - Mount the rotary adapter and tighten the screw with an 8 mm hex wrench.
1 - Mount the rotary adapter and tighten the screw with an 8 mm hex wrench.
Installation, Operation, & Maintenance Manual
1 - Mount the rotary adapter and tighten the screw with an 8 mm hex wrench.
Figure 5-6 Rotary Adaptor
Figure 5-6 Rotary Adaptor
ES-09374-1
Figure 5-6 Rotary Adaptor
2 - The rotary support is factory assembled for actuators with 30x80 holes and 30mm
shaft height. If you need to modify, refer to Section 5.3.1 - Mounting the Rotary Support
According to the Actuator.
Figure 5-7 Universal Rotary Mounting Kit
2 - The rotary support is factory assembled for actuators with 30x80 holes and 30mm
2 - The rotary support is factory assembled for actuators with 30x80 holes and 30mm
2 - The rotary support is factory assembled for actuators with 30x80 holes and 30mm
shaft height. If you need to modify these measures, refer to item 5.3.1 - Mounting the
shaft height. If you need to modify these measures, refer to item 5.3.1 - Mounting the
shaft height. If you need to modify these measures, refer to item 5.3.1 - Mounting the
Rotary Support to the Actuator.
Rotary Support to the Actuator.
Rotary Support to the Actuator.
Figure 5-7 Universal Rotary Mounting Kit
Figure 5-7 Universal Rotary Mounting Kit
Figure 5-7 Universal Rotary Mounting Kit
3 - Mount the bracket to the positioner by placing the four M6x10 screws with lock
washers and plain washers. Tighten the screws with a 10 mm wrench.
Figure 5-8 Mounting the Bracket on the Positioner
3 - Mount the bracket to the positioner by placing the four M6x10 screws with lock
3 - Mount the bracket to the positioner by placing the four M6x10 screws with lock
3 - Mount the bracket to the positioner by placing the four M6x10 screws with lock
washers and plain washers. Tighten the screws with a 10 mm wrench.
washers and plain washers. Tighten the screws with a 10 mm wrench.
washers and plain washers. Tighten the screws with a 10 mm wrench.
Figure 5-8 Mounting the Bracket on the Positioner
Figure 5-8 Mounting the Bracket on the Positioner
Figure 5-8 Mounting the Bracket on the Positioner
ATTENTION
ATTENTION
ATTENTION
Do not touch the actuator shaft when it is running, as moving it may cause accidents with
The positioner can be installed at any starting angle and operates in any position,
The positioner can be installed at any starting angle and operates in any position,
The positioner can be installed at any starting angle and operates in any position,
serious injuries.
vertical or horizontal.
vertical or horizontal.
vertical or horizontal.
CAUTION
CAUTION
CAUTION
Be careful when handling compressed air hoses, make sure the line is disconnected
Be careful when handling compressed air hoses, make sure the line is disconnected
Be careful when handling compressed air hoses, make sure the line is disconnected before
Be careful when handling compressed air hoses, make sure the line is disconnected
before connecting it to the positioner.
before connecting it to the positioner.
connecting it to the positioner.
before connecting it to the positioner.
IMPORTANT
IMPORTANT
IMPORTANT
The positioner can be installed at any starting angle and operates in any position,
The positioner can be installed at any starting angle and operates in any position,
The positioner can be installed at any starting angle and operates in any position,
The positioner can be installed at any starting angle and operates in any position, vertical or
vertical or horizontal.
vertical or horizontal.
vertical or horizontal.
horizontal.
Mechanical Installation
Mechanical Installation
Mechanical Installation
18
Mechanical Installation
August 23, 2022
Mechanical Installation
13
13
13
Advertisement
Table of Contents
