Electrical Requirements; StorageDrawerRemoval - GE JGSP42SETSS Installation Instructions Manual

3  a LterNateINstaLLatION/CONstruCtIONkIts
Backguardkit: Used when replacing a free-standing range with a slide-in range. Adds a decorative
backguard to the rear of the range. This kit can only be used when the opening in the countertop is
25" (63.5 cm) deep.
MaintopFillerkit: Adds a filler strip to the rear of the range. This kit can only be used when
the opening in the countertop is 25" (63.5 cm) deep. This kit cannot be used with a backguard kit.
MaintopFillerkitNumbers:wB07t10680(Black)
wB07t10681(white)
wB07t10682(Bisque)
Bodysidekit: Used when cabinets are absent on one side of the range. Contains a color-matched
side panel which can be used to create a finished appearance on either side of the range.
Lowertrimkit: Contains a color-matched toe kick and extra-long leveling legs. Designed to be used
when the range needs to be raised higher than 36-1/2" (92.7 cm) to 38" (96.5 cm).
To order accessory kits, call 1.866.775.4557, or visit www.GEAppliances.com.
4 P reParetheraNGe


stOraGeDrawerreMOVaL

a. Pull drawer out until it stops.
B. Lift front of drawer until the stops clear the guide.
C. Pull forward and remove the drawer.
DOOrreMOVaL(optional)
Door removal is not a requirement for installation of the product but is an added convenience.
toremovethedoor:
a. Open the oven door as far as it will go.
B. Push both hinge locks down toward the door frame to the unlocked position. This may
require a flat-blade screwdriver.
DONOtLIFttheDOOrBYthehaNDLe!
C. Place hands on both sides of the door, and close the oven door to the removal position.
(Approximately 1"–2" [2.5 cm–5.1 cm] from the closed position.)
D. Lift door up and out until the hinge arms clear the slots.
NOte: The oven door is very heavy. Be sure you have a firm
grip before lifting the oven door off the hinges. Use caution once
the door is removed. Do not lay the door on its handle. This could
cause dents or scratches.
31-10675-1
31-10737-1 = French version
31-10738-1 = Spanish version
09-2009 GE

5 ELECTRiCAL REqUiREmEnTS

IMPOrtaNt:This appliance must be electrically grounded in accordance with local codes or,
in the absence of local codes, with the national Electrical Code, AnSi/nFPA 70 or Canadian
Electrical Code, CSA C22.1.
This appliance must be supplied with 120 VAC / 60 Hz power. it must be connected
to a properly grounded branch circuit, protected by a 15-amp or 20-amp circuit breaker or fuse.
We recommend that a separate circuit serving only this appliance be provided.
The power cord of this appliance is equipped with a three-prong (grounding) plug which mates
with a standard three-prong grounding wall receptacle. The customer should have the wall
receptacle checked by a qualified electrician to make sure the receptacle is properly grounded.
Where a standard two-prong wall receptacle is encountered, it is the personal responsibility
and obligation of the customer to have it replaced with a properly grounded three-prong wall
receptacle.
Donot,underanycircumstances,cutorremovethethirdprong(ground)fromthe
powercord.
Because of potential safety hazards under certain conditions, we strongly recommend against
the use of an extension cord. However, if you still elect to use an extension cord, it is absolutely
necessary that it is a UL-listed 3-wire grounding-type appliance extension cord, and that the
current-carrying rating of the cord in amperes is equivalent to, or greater than, the branch
circuit rating.
Rail
Guide
installation of this product in a mobile home must conform with the manufactured Home
Construction and Safety Standard, Title 24 CFR, Part 3280. if this standard does not apply,
you must follow the standard for the manufactured Home installations, AnSi A225.1 and
manufactured Home installations, Sites and Communities and AnSi/nFPA 501A or with
local codes.
Stop
Stop
Hinge
unlocked
Hinge
position
slot
Hinge
arm
Hinge clears slot
warNING:
thisappliancemustbeproperlygrounded.