Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for VETEC V-LINK 67601
Summary of Contents for VETEC V-LINK 67601
- Page 1 USER INSTRUCTIONS ENGLISH, V1.0 V-LINK 67601 / 671201 / 672501 / 675501...
- Page 2 Front Back A Capacity / Product brand H Capacity / Serial no. engraved B Red LED display USB port (only for charging) C Operating panel Safe Working Load (SWL) D Manufacturer name K Item no. E ON/OFF button Read manual. CE F Tare button M Manufacturer name G Hole for shackle...
- Page 3 Quick start guide The instructi ons contained in this quick guide do not replace the full manu- al. Make sure to read the whole manual carefully and correctly before use.. On/off Press ON/OFF to turn on and off . Once pressed, the display shows the soft - ware version number for a few seconds.
-
Page 4: Table Of Contents
Summary Thank you for purchasing a V-LINK dynamometer Page 1.1 Important information 1.2 YouTube video tutorials 2.1 Technical specifications 2.2 Dimensions 2.3 Remote wireless display 2.4 Accessories 2.5 Applicable standards and regulations Installation, operation and uninstalling Page 3.1 Installation 3.2 Operation 3.3 Uninstallation 3.4 Overload Basic settings... -
Page 5: Thank You For Purchasing A V-Link Dynamometer Page
Failure to follow these warnings could result in serious injury and property damage. Every use should be carried out according to current regulations in the country of use. Vetec A/S is not responsible for local regulations not being followed. -
Page 6: Technical Specifications
2.1 Technical specifi cati ons Varenummer: 670601 671201 672501 675501 Max. working capacity 6.5T 12.5T Accuracy (%) +/- 0.2% FS Accuracy (Kg.) +/-15 Kg.* +/-30 Kg.* +/-50 Kg.* +/-120 Kg.* Safe overload (%) 110% Safe overload (Kg.) 7150 Kg. 13200 Kg. 27500 Kg. -
Page 7: Remote Wireless Display
2.3 Remote wireless display Duplex communicati on and a long range enable measurements to be read from a long distance. To avoid interference the dynamometer and display can be connected using 99 diff erent channels. Item no. WRDX01 Applicati on areas Only applicable with a V-LINK dynamometer. -
Page 8: Applicable Standards And Regulations
3.1. Installati on The V-LINK must be fi tt ed with shackles that comply with the SWL of the dynamometer and the applicable legislati on in the country of use. Vetec A/S recommends Green Pin standard Shackles, G4163 and G-4161. -
Page 9: Operation
Overload test: Turn the dynamometer off and on. If it indicates a value ”DANGER” much higher or lower than the usual starti ng value, it has been permanently damaged. In this case, it is imperati ve to have it checked by Vetec’s service department before further use. - 5 -... -
Page 10: Basic Settings
4. Basic setti ngs Tænk og sluk Press ON/OFF to turn on and off . Once pressed, the display will show the soft ware version number for a few seconds. Then the untared value will show. *The dynamometer will not automati cally turn off if not used. Tare functi on To acti vate the tare functi on press and hold →0←... -
Page 11: Menu / Advanced Settings
5. Menu / Advanced settings 5.1. Peak hold (Menu 1) Activate peak hold Press the ON/OFF button. Press and hold MENU until the display shows 1. Select 1 (Menu 1) by pressing ENTER. The display now shows PEoFF (Peak hold off). Press to go to PE on (Peak hold on). -
Page 12: Operating Multiple Dynamometers In The Same Area ( Menu 2 )
Deacti vate peak hold Press and hold MENU unti l the display shows 1. Select 1 by pressing ENTER. The display now shows PE on. Press unti l the display shows ·PEoFF. Press ENTER to turn off Peak Hold. Press RETURN to go to default setti ngs. *Peak hold will not deacti vate when the dynamometer is turned off . -
Page 13: Faq
7. Charging V-LINK is charged using a standard high quality USB charger. Always on stock at Vetec or available in any store. Charge the dynamometer in your car, connected to your computer or using a wall charger. As the charger is not waterproof charging the unit in a safe dry place is recommended. -
Page 14: Service, Repairs And Maintenance Page
To prevent damage to the dynamometer, make sure that repairs and recalibration are carried out by qualified personnel. It is recommended that recalibration and repairs are done at Vetec’s service department located in Denmark or by authorized partners. Contact Vetec’s service department for further information. -
Page 15: Waste Electrical And Electronic Equipment (Weee)
In the event of a defect during the warranty period, the dynamometer must be returned, with freight (and all duti es and taxes) prepaid by the Buyer. Vetec A/S or the distributor will, according to their choice, repair or replace the defecti ve unit.