Advertisement
Quick Links
FD30EX SLIDING DOOR SYSTEM Installation Manual
(Ceiling Mount Type for Pocket Door, with Dual Soft Close)
Thank you for using our product. Before installation, please read this manual thoroughly to ensure correct installation.
Please keep this manual at hand for future reference.
ABOUT THE PRODUCT
T his is a parts set for a sliding door system for indoor use.
●
●
opens with a 1 step soft motion.
T wo sections of track for easy maintenance after installing.
●
SPECIFICATIONS
Max. Door height
Door width
Min. Door thickness
Max. Door weight
Vertical adjustment
Depth adjustment
・ T he closing speed of the soft closing type door may change
depending on the ambient temperature, operating method or
installation quality.
・ R ecommended ambient temperature range is 5 to 40 degrees
centigrade.
1
When using a light weight door, you may feel the resistance of
※
the soft closer when opening the door.
FOR YOUR SAFETY AND CORRECT INSTALLATION
Meaning of symbols
Warning
Prohibited
Caution
WARNING:
If not followed, death or serious injury may result.
This product should be installed by a qualified person in accordance with this manual. If it is not installed correctly, the door
may fall and cause injury.
Provide a frame that can withstand the weight and impact of opening and closing the door. Be sure to use the specified screws
and tighten them securely. If the mounting strength is insufficient, the door may fall and cause injury.
Do not use this product for any other purpose, or with doors that are outside the specifications of this manual.
Do not disassemble or modify any parts other than those described in this document.
Caution:
If not followed injury or damage may result.
Follow the specified dimensions, specifications, and alignment of the door and frame. Warping, tilting or twisting of the frame
or door may cause failure.
If cutting any parts, make sure to remove any burrs before installation. Also check the upper track for any left-over burrs or
scraps and remove these.
This product is a part for architectural fittings. After installation, please check the function and safety of the final product.
Please inform the end user how to use the product safely.
Make sure to check the screws for slack at regular intervals (one month from first usage, half a year, and then one time every
year is recommended).
When installing the "pocket door", make an "easy-maintenance" structure. For example, use a removable panel.
Install the product with two people (in the case of one person, there is a risk of damaging components).
and
2400 mm
590 - 1000 mm
30 mm
1
30 kg/door
※
4 mm upward
3 mm downward
±2 mm
Required
Part No.FD30EXDHCP-PD
Door pocket
Door
1
Advertisement
Related Manuals for Lamp FD30EX
Summary of Contents for Lamp FD30EX
- Page 1 FD30EX SLIDING DOOR SYSTEM Installation Manual (Ceiling Mount Type for Pocket Door, with Dual Soft Close) Part No.FD30EXDHCP-PD Thank you for using our product. Before installation, please read this manual thoroughly to ensure correct installation. Please keep this manual at hand for future reference.
-
Page 2: Component Parts
Floor guide (Surface mounted） (recessed mount） (two-way) Cord No. 250-043-910 250-020-837 250-029-705 250-029-704 250-017-151 Part No. FD30-35EV-TRMP 型 FD30-35EV-TRHP 型 FD30EX-WRH-DSC-A FD30-WRH-N FD30-TRGPF FD30-TRGPB FD30-HBG Parts 1 ea 1 ea 1 ea 1 ea 1 ea Countersunk head tapping screws... -
Page 3: Installation Procedure
INSTALLATION PROCEDURE Cutting track and Hole Drilling on Upper Track Caution Caution When cutting, reinforce the Do not cut the track on the track to prevent deformation side with three holes. at the cut section. When using 860 mm track and 1260 mm track (1 ea.) Leading edge Connecting side Track length for open area: Lo... - Page 4 Mounting Parts on Door Pull out casing. ②③Main unit Raise lever. Installing Pocket Trigger Insert end with the pin. ⑤Pocket trigger Door pocket track Pay attention to the Insert the pocket trigger direction. until it reaches the end of the track. Verification Before Installing Soft Closer Caution ...
- Page 5 Mounting of Open Area Track Caution 【1 Connecting to door pocket track. Overlap the two countersunk holes Align the track end to the end of on the pocket trigger and the two the door pocket track. holes on the open area track. Deviation of the joint position makes Pull out the pocket trigger from insertion of the trigger difficult.
- Page 6 Mounting of Floor Guide Position floor guide Caution below the center of the upper Fasten the four countersunk holes The position of the model where track, so that it is covered by with provided screws. the margin occurs is shown in the door when it is opened the figure.
- Page 7 Adjusting The Door Position Adjust the door so that it is parallel to the upper track with 6 - 13 mm of clearance between the door and floor. Caution The adjustment of the door should be done Do not turn the adjustment screw beyond adjustment range. with the jump prevention nut loosened.
- Page 8 Appendix 1 How to Remove Door, Track 【1】 How to remove door Soft closer Put a support of 10 mm thickness under the door. Pull out the leading edge roller (main unit) from the casing, while pushing the lever on the roller. Remove door Pull out the door, while making sure not to let it scratch against the door pocket.
- Page 9 Appendix 2 How to Shift the Connecting Position of the Tracks 【1】 When determining the trigger position on site Put a mark on the open area track with reference to the leading edge (1) Put a mark on the open area track with reference to the of the door.
-
Page 10: Troubleshooting
SUGATSUNE AMERICA, INC Tokyo, JAPAN Shanghai, CHINA California, USA Phone: +81 (0)3 3866 2260 E-mail:export@sugatsune.co.jp Phone: +86 21 3632 1858 E-mail:lamp@sugatsune.com.cn Phone: +1 310 329 6373 E-mail:sales@sugatsune.com SUGATSUNE KOGYO (UK) LTD Guangzhou, CHINA Illinois, USA Reading, UK Phone: +86 20 6639 3552 E-mail:lamp@sugatsune.com.cn...