Table of Contents
Advertisement
10x13ft Rectangle Offset
Umbrella with Resin Base
Assembly & Care Instructions
SKU #: 272-1774
Model #: UMB-952371
IMPORTANT : RETAIN FOR FUTURE REFERENCE
READ CAREFULLY
The schematics in this manual are for assembly and operation illustration only.
They may differ from the actual appearance.
For assistance with assembly, parts, or customer service, please contact:
ATLeisure, LLC
Toll Free: 1-855-880-7205 (English is offered)
8am - 5pm, Monday through Friday, Eastern Standard Time
Email: customerservice@atleisure.com or visit our website at www.atleisure.com
DO NOT RETURN TO STORE
2020 Distributed by Menard, Inc., Eau Claire, WI 54703
Made in China
Advertisement
Table of Contents
Related Manuals for Backyard Creations UMB-952371
Summary of Contents for Backyard Creations UMB-952371
- Page 1 10x13ft Rectangle Offset Umbrella with Resin Base Assembly & Care Instructions SKU #: 272-1774 Model #: UMB-952371 IMPORTANT : RETAIN FOR FUTURE REFERENCE READ CAREFULLY The schematics in this manual are for assembly and operation illustration only. They may differ from the actual appearance.
-
Page 2: Table Of Contents
Contents Preparation ....... . . 2 Hardware Contents ......2 Package Contents . -
Page 3: Package Contents
Package Contents Part Description Quantity Blow Molded Base Outside (with cap) Blow Molded Base Inside (with cap) Lower Cross Leg Upper Cross Leg Holder Pole 360° Swivel Umbrella Frame (with canopy) Glide Handle Pole Support Cap Cap for Blow Molded Base Connected Pole Crank Handle... -
Page 4: Umbrella Assembly
Assembly Remove all protective materials. Be careful not to throw away small parts such as bolts, washers, etc. that may be wrapped in the protective materials. Step 1: Put the cross legs (C & D) on a flat surface. Attach the bottom of connected pole (P) to the upper cross leg (D) and insert a long bolt (HH) through a washer (KK) and tighten using the hex wrench (E). - Page 5 Assembly (continued) ② ③ ① Step 2: Insert the umbrella frame with canopy (CAN) onto the holder pole (F). At the same time, slide holder pole collar onto the holder pole (F). Place a long bolt (HH) through a washer (KK) into the holder pole (F) and use the hex wrench (E) to tighten.
-
Page 6: Umbrella Operation
Assembly (continued) Step 3: Fill up each blow molded base (A & B) with sand water and cover with cap (M). Place the pole support cap (L) onto the holder pole (F) and lay everything on top of the blow molded base (B). Umbrella Operation Close Open... - Page 7 Umbrella Operation (continued) Step 3: The umbrella has a unique design that moves the pole out of your way and off to the side. The multiple position canopy can rotate 360° around the axis of the main pole to shade your desired area. 360°...
-
Page 8: Warranty
Canopy Care • Simply clean the umbrella canopy with soft brush and mild detergent. • DO NOT machine wash or dry. • DO NOT iron. • AIR DRY the canopy thoroughly before storing for extended period of time. Make sure the canopy is completely open during the drying process to prevent shrinkage. -
Page 9: Replacement Parts
Replacement Parts For replacement parts, call our customer service department at 1-855-880-7205, 8:00am-5:00pm., EST, Monday-Friday. Part Description Quantity Re-Order Number Blow Molded Base Outside BSE-ABMP-11-BWN-T-C2 Blow Molded Base Inside BSE-BBMP-11-BWN-T-C2 Lower Cross Leg CSL-C78RX-BWN-T-C2 Upper Cross Leg CSL-D78RX-BWN-T-C2 Holder Pole HDP-F78RX-BWN-TM 360º... - Page 10 ATLeisure, LLC 1040 Boulevard SE, Suite B Atlanta, Georgia 30312, USA Customer Service Toll Free 1-855-880-7205 8am - 5pm Eastern Time, Monday through Friday www.atleisure.com 2020 Distributed by Menard, Inc., Eau Claire, WI 54703 Made in China...