Maintenance Recommendations; After Sales Service - Supra ARIO Installation Instructions And User Manual

TABLE (*)
CONTROLS
Lighting the fire Open / Draught
Nominal efficiency
Performance in
slumber mode
Door handle
To open-close the door:
- When the appliance is cold, directly with your hands
- When the appliance is hot, with an insulating glove.
LIGHTING THE FIRE FOR THE FIRST TIME
Remove the self-adhesive labels (except for the nameplate), any
possible blocking cards, and make sure that the ash tray is empty.
Start with a small fire and gradually increase the load. This
progressive heating allows the materials to expand slowly and to
stabilise. There may be some fumes and odours, due to the
paintwork. These will gradually disappear. Do this for a few days
until normal use. Open the windows during the first hours of
operation.
When heating up for the first time, check the draught according to
the technical specifications table.
SERVICE
Lighting the fire
To light your appliance, preferably follow the fire lighting procedure
described above. This fire lighting technique makes it possible to
heat up the flue and to remove any blockages (negative pressure)
that may form when the weather is bad or cold, thereby preventing
the air from blowing back into the room when the fire is lit.
The procedure is as follows:
- Put the air combustion control to the maximum setting.
- Place 2 logs on the firebox grid.
- Place the kindling wood in the shape of a tower on top of the
logs.
- Put 1 or 2 fire-lighter cubes on the wood and set alight.
- Close the door.
For further information, view the Supra video on youtube at:
https://www.youtube.com/watch?v=ebOr4vMj2Jo
TAKE NOTE! Never use petrol, alcohol or fuel-oil, etc.
Reloading
Reload the appliance once there is a good bed of embers and the
flames have gone out. Gently open the loading door, to prevent
fumes from getting out (if opening during the combustion stage) or
embers from falling. Once the wood has been loaded, close the
door
Nominal efficiency
Adjust the controls according to the table (*). The intensity of the
fire will be determined by the amount of fuel. The correct operation
of the appliance depends on a suitable air supply.
NOMINAL LOADING
For the optimum operation, load 2 small logs of wood. Place the
logs to the back of the appliance to prevent embers from falling
out.
STOVE
3/4
1/2
Performance in slumber mode
Adjust the controls according to the table (*). Do not operate the
appliance in slumber mode for long periods of time. The
temperature of the combustion gases is insufficient and, instead of
being eliminated, they condense in the flue pipe. This increases
the amount of dirt in the chimney and appliance (walls and glass).
IN THE EVENT OF AN INCIDENT
In the event of an incident in the room (fire in the chimney, fire in
the room, etc.), quickly close the loading door and all the stove
controls. Do not pour water into the firebox. Call the fire brigade.
4. MAINTENANCE - RECOMMENDATIONS
ASH REMOVAL
The ashes can be removed when the stove is operating. Regularly
empty the removable ash tray. The build-up of ashes hinders the
air flow under the grid, distorting the flow and affecting
combustion. Then replace the ash tray.
CLEANING THE FRONT AND SIDES
Do not use water, solvents or abrasive products (not even slightly)
to clean the stove, only a soft, dry cloth.
CLEANING THE GLASS WINDOW
Clean the glass when it is cold, with a damp cloth dipped in wood
ashes. The air sweep system keeps the glass as clean as
possible. However, during normal operation, there may be a slight
darkening in some areas of the glass. In slumber mode, the air
sweep is less efficient.
SOOT REMOVAL
The legislation provides for 2 chimney sweeps a year (including
one during the heating period) to be performed with mechanical
means (rotary brush). Keep the documents signed by the company
responsible for this work as proof that this has been done.
ANNUAL MAINTENANCE
After each heating season, clean the stove thoroughly and check
that all moving parts of the appliance are operating correctly.
Check the conditions of the seals and the parts in contact with the
flames.
5. AFTER-SALES SERVICE
The appliance has parts that are subject to wear and tear and
should be checked during the annual maintenance. Your stockist
will supply you with the necessary spares.
When requesting information or spares, you need to indicate the
part number and the serial number of the appliance, which can be
found on the nameplate. Only use the spares supplied by the
manufacturer.