The purpose of this manual is to inform the operator and the maintenance engineer regarding the safe and correct use of the Allegro Powder Bag Lift. This includes all people who have the task of installing, commissioning, adjusting, maintaining, cleaning, repairing, transporting or scrapping this lift.
When the lifting hook attachment is in the highest position, movement is limited to approximately one meter for position the lifting device under the designated Pall hardware. WARNING! Risk of hands and feet getting caught in machine! Do not stand on or rest your feet on the legs or battery casing.
10. Any part of this lifting device which shows signs of wear or other damage must be replaced immediately. The lifting device must not be used before the damaged part is replaced. Welding and other mechanical modifications to the lifting device must be carried out by authorized staff.
Lifting height can be limited by adjusting the sensor on the side of the mast. Wheel base 660 mm, adjustable between 660-750 mm. Hook position Hook position is adjustable @322, 522 and 722 mm from the mast. Hook attachments Hook has 3 attachment points for holding different sized powder handling bags. www.pall.com/biopharm www.pall.com/biopharm...
Installing Battery Pack 1. Loosen the locking plate with the black thumb screw and slide it to the top. 2. Lift the battery pack out of the battery compartment. 3. Connect the cables. 4. Put the battery back into the battery compartment. Be careful not to trap the cables.
(see Section 9.4.Raising and lowering the lifting hook attachment) Slide the lifting hook attachment in the T-bar connection of the lift. 2. Hand tighten all 6 bolts of the lifting hook attachment by using the provided Allen key. 3. Install the provided plugs. www.pall.com/biopharm...
Section 9.7. Moving the lifting device If necessary, adjust wheel base width of the lifting Section 9.8. Adjusting wheel base width device to fit under the used Pall hardware. Lock the wheels. Section 9.2. Locking and unlocking wheels Adjust the hooks on the lifting hook attachment to suit Section 9.9.
Raising and Lowering the Lifting Hook Attachment Use the detachable two-speed controller to raise or lower the lifting hook attachment. Press- ing the buttons gently will move the lifting hook attachment at a low speed. Pressing hard will increase the speed. www.pall.com/biopharm...
Adjusting the Sensor The lift has an adjustable sensor to limit the height of the lifting hook attachment. This can be useful in cases where the ceiling is lower than the total height of the lift. 1. Remove protective cover on the side. Careful not to damage the lift. 2.
Take into account that the rear wheels can swivel, the front wheels are fixed. Adjusting Wheel Base Width The wheel base can be widened in case the alignment of the lift with the Pall hardware is not ideal. This can only be executed with proper safety measures and by the correct technical per- sonal within the company.
When all of the previous steps have been completed you can now use the lift in combination with a designated Pall container or other Pall hardware. Depending on the type of hardware you can place the lift on the sides or the front/back.
Tape switches defective. Loading platform fails to stop Have device repaired by the while being lowered when an manufacturer. object comes in contact with the tape switches. www.pall.com/biopharm...
General Maintenance It is recommended that the Allegro Powder Bag Lift is serviced on an annual basis. For further details on technical service, maintenance or repair, please contact your Pall representative. If any damage is found or any part of the product is not functioning normally then do not continue using the product and contact Pall for help and advice.
However, as the legislation and facilities vary throughout the member states, please contact your local Pall sales office or distributor to discuss the available options for correctly disposing of this product.
Pall Manufacturing UK Ltd Walton Road, Farlington, Portsmouth Hampshire, PO6 1TD, England Pall Portsmouth Manufactured Systems Group hereby declares that in compliance with the above directive, the product(s) detailed have been designed and manufactured in accordance with the standards stated below.
The information provided in this literature was reviewed for accuracy at the time of publication. Product data may European Headquarters be subject to change without notice. For current information consult your local Pall distributor or contact Pall directly. Fribourg, Switzerland +41 (0)26 350 53 00 phone LifeSciences.EU@pall.com e-mail...
Need help?
Do you have a question about the Allegro and is the answer not in the manual?
Questions and answers