Playback - JVC HR-S9911U Instructions Manual

D
Connect Controller to VCR
Connect the Controller to the CABLE BOX Controller connector
on the rear panel.
E
Turn on cable box or DBS receiver
Select a channel other than channel 9 on your cable box, or
channels 100, 205 on your DBS receiver.
F
Access Main Menu screen, then Initial Set screen on VCR
Press MENU on the Remote. Press
(arrow) to "INITIAL SET", then press OK or
G
Access Cable Box Set screen or DBS
Receiver Set screen
Press to move the highlight bar
rt
(arrow) to "CABLE BOX SET" or "DBS
RECEIVER SET", then press OK or
H
Select output channel
Your selection depends on how the unit is
connected to your VCR.
If the unit is connected to your VCR's
ANTENNA IN terminal on the rear
panel, Press until the channel
rt
number representing the cable box's
output (CH2 – CH9) or DBS receiver's output (CH3 or CH4)
appears on the screen.
If the unit is connected to your VCR's AUDIO/VIDEO IN
connectors on the front panel, press
(FRONT)" appears on the screen.
If the unit is connected to your VCR's AUDIO/VIDEO IN
connectors on the rear panel, press
appears on the screen.
If you do not use any unit, press
the screen.
I
Access Brand Set screen
Press OK or e.
If the Clock Set screen appears, perform "Manual Clock Set"
( pg. 7). If you press MENU after the clock has been set, the
Brand Set screen appears.
J
Enter brand code and perform test
Press the appropriate Number keys on the
Remote to enter the brand code from the
following list, then press OK or e.
CABLE BOX BRAND
ARCHER
CABLETENNA
CABLEVIEW
CITIZEN
CURTIS
DIAMOND
GC BRAND
GEMINI
GENERAL INSTRUMENTS
HAMLIN
JASCO
JERROLD
NOVAVISION
OAK
PANASONIC
PULSER
RCA
REGAL
REMBRANDT
SAMSUNG
SCIENTIFIC ATLANTA
SIGMA
SL MARX
SPRUCER
STARGATE
TELEVIEW
TOCOM
UNIKA
UNIVERSAL
VIDEOWAY
ZENITH
to move the highlight bar
rt
.
e
.
e
until "ON F-1
rt
until "ON L-1 (REAR)"
rt
until "OFF" appears on
rt
CODE
1, 5, 17
1, 17
15, 16, 17, 21, 25
15, 16, 17, 21, 25
2, 8
1, 17
15, 16, 17, 21, 25
15
1, 4, 6, 11, 12, 15, 28
10, 18, 23
15
1, 4, 6, 11, 12, 15, 28
2, 8
7, 20
13, 14
15, 16, 17, 21, 25
13, 14
10, 18, 23
1, 16, 17
5, 16, 24
2, 8
7, 20
5, 16, 17, 24, 25
13, 14
5, 15, 16, 17, 21, 24, 25
5, 16, 24
1, 4, 16
1, 17
16, 17, 25
3, 9, 22
3, 9, 22
DBS RECEIVER BRAND
JVC (DISH Network)
ECHOSTAR (DISH
Network)
For cable box
If the cable box's channel changes to 9,
setting is complete. Press OK.
If the cable box's channel does not
change to 9;
A Press rt to move the highlight bar
(arrow) to "NO", then press OK or e.
B Repeat step 0 0 0 0 until the cable box's channel changes to 9 by
entering another code.
C If the channel does not change after going through all the code
numbers listed for your model of cable box, then try all the
other numbers.
For DBS receiver
If the DBS receiver's channel changes to
the channel listed below for your brand,
setting is complete. Press OK or e.
JVC 100
]
ECHOSTAR 100
]
If the DBS receiver's channel does not
change as shown above;
A Press rt to move the highlight bar (arrow) to "NO", then
press OK or e.
B Repeat step 0 0 0 0 .

Playback

Basic Playback
Turn on the VCR and TV, and select the VCR channel (or AV
mode).
Set the VCR/TV/CABLE/DBS selector on the Remote to
"VCR".
A
Load a cassette
Make sure the window side
is up, the rear label side is
facing you and the arrow on
the front of the cassette is
pointing towards the VCR.
Do not apply too much pressure when inserting.
The VCR turns on automatically.
The tape will run for a few seconds while the VCR searches for
the tape number.
If the cassette's record safety tab has been removed, playback
begins automatically.
NOTE:
When you use the Video Navigation function, operate the VCR
only after the tape number is detected; otherwise, you cannot use
the Video Navigation function.
B
Start playback
Press PLAY ( ).
4
The S-VHS indicator lights up when you play back a tape
recorded in S-VHS mode or in S-VHS ET mode (
— 9 —
CODE DBS RECEIVER BRAND
51 SONY (DSS)
51 RCA (DSS)
SONY 205
]
RCA 205
]
CONTINUED ON NEXT PAGE
CODE
41
40
REW FF
pg. 13).