Editing With Another Vcr - JVC HR-S9911U Instructions Manual

Editing with Another VCR

You can use your VCR as the playback or recording VCR. Refer
also to the other components' instruction manuals for connection
and its operations.
A
Make connections
Example 1: When another VCR is VHS VCR
Connect two VCRs with the supplied audio/video cable.
To AUDIO/VIDEO IN
When using this VCR
as the recording VCR,
connect this VCR's
AUDIO/VIDEO IN
connectors to the
audio/video output
connectors on another
VCR.
To audio/video output
If another VCR is monaural, connect this VCR's AUDIO L IN (or
OUT) connector to the audio output (or input) connector on
another VCR.
Example 2: When another VCR is S-VHS VCR and when using
this VCR as the playback VCR
This VCR (for playback)
To AUDIO OUT
Audio cable
(not supplied)
To audio input
Another VCR (for recording)
This VCR
To AUDIO/VIDEO OUT
When using this VCR
as the playback VCR,
connect this VCR's
AUDIO/VIDEO OUT
connectors to the
audio/video input
connectors on another
VCR.
To audio/video input
Another VCR
To S-VIDEO OUT
S-video cable
(supplied)
To S-video input
Example 3: When another VCR is S-VHS VCR and when using
this VCR as the recording VCR
To AUDIO input
Audio cable
(not supplied)
To audio output
B
Load cassettes
Insert the playback cassette into the playback VCR and the
cassette to be recorded on into the recording VCR.
C
Select input location on recording VCR
Select the correct external input location on the recording VCR.
On this VCR (when using this VCR as the recording VCR);
Select "L-1" —when connecting the other VCR to the audio/video
(or S-video) input connectors on the rear panel.
Select "F-1" —when connecting the other VCR to the audio/video
(or S-video) input connectors on the front panel.
On the VCR
Press CH+/– or push the ADVANCED JOG dial, then turn it to the
left or right until "L-1" or "F-1" appears on the display panel.
On the Remote
Press AUX and/or CH+/– until "L-1" or "F-1" appears on the
display panel.
D
Select video input connector on recording VCR
When using this VCR as the recording VCR, select the appropriate
mode depending on the connector being used (
When using S-VIDEO input connector on the front panel, set
"FRONT AUX INPUT" to "S-VIDEO".
When using S-VIDEO IN connector on the rear panel, set "REAR
AUX INPUT" to "S-VIDEO".
When using VIDEO input connector on the front panel, set
"FRONT AUX INPUT" to "VIDEO".
When using VIDEO IN connector on the rear panel, set "REAR
AUX INPUT" to "VIDEO".
E
Select edit mode
Set the edit mode to "ON" for the VCRs if such a mode is
equipped.
On this VCR, set "PICTURE CONTROL" to "EDIT" (
F
Start playback
Press PLAY ( ) on the playback VCR.
4
G
Start recording
Press REC ( ) on the recording VCR.
7
NOTE:
Be sure to select "AUTO" for "PICTURE CONTROL" (or "NORM"
when "VIDEO CALIBRATION" is set to "OFF") after you finish
dubbing the tapes. (
— 24 —
This VCR (for recording)
To S-VIDEO input
S-video cable
(supplied)
To S-video output
Another VCR (for playback)
pg. 20)
pg. 21).
pg. 20).