Table of Contents
Advertisement
Quick Links
OPERATING INSTRUCTIONS
Edition 1
IMPORTANT!
To qualify for full 36 month warranty, you must register within 30 days of purchase. See inside for details.
Read these Operating Instructions Completely before attempting to use this machine. Save this manual and
keep it handy for quick reference. Pay particular attention to the safety instructions we have provided for
your protection. Contact your distributor if you do not fully understand anything in this manual.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Weldclass CutForce CF-45P
Summary of Contents for Weldclass CutForce CF-45P
- Page 1 OPERATING INSTRUCTIONS Edition 1 IMPORTANT! To qualify for full 36 month warranty, you must register within 30 days of purchase. See inside for details. Read these Operating Instructions Completely before attempting to use this machine. Save this manual and keep it handy for quick reference. Pay particular attention to the safety instructions we have provided for your protection.
-
Page 2: Contents
The air regulator/filter supplied with the CF-45P machine provides the minimum level of filtration. However, we strongly recommend the WELDCLASS PLATINUM Z-20 high-performance air filter, available as an optional accessory from your Weldclass distributor. This attaches to the inlet of the existing regulator/filter and provides excellent filtration down to 1-micron. -
Page 3: Table Of Contents
Air Compressor / Air Supply .....................13 5.4.3 Air Hose & Fittings........................13 OPERATING ENVIRONMENT ........................14 Location ............................14 Ventilation ............................14 BASIC OPERATION ..........................15 Setup ............................15 Cutting ............................15 Distance from the Tip to the Work Piece ..................16 © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05... - Page 4 Fire & Explosive Risks ......................33 13.4.8 Sparks & Hot Metal ......................34 WARRANTY ............................35 14.1 Warranty period ...........................35 14.2 Warranty Includes and Covers......................35 14.3 Warranty Excludes / Does Not Cover ...................35 14.4 Warranty Conditions ........................36 © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05...
-
Page 5: Basic Specifications
30A / 92V @ 100% Nominal Open Circuit (pilot arc) Voltage 210V Table 1 For full machine specifications, refer to technical data plate on base of machine – or go to: www.Weldclass.com.au/CF-45P © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05... -
Page 6: Know Your Machine
6. Mains Power Switch 7. Air Regulator Adjustment Knob 8. Air Regulator Gauge 9. Compressed Air Inlet Connection 10. Air Regulator 11. Air Filter Bowl 12. Air Filter Moisture Drain Tube Figure 2 © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05... -
Page 7: Control Panel
16. Perforated Sheet Cutting Mode Indicator Light 17. Normal Cutting Mode Indicator Light 18. Air Test Mode Indicator Light 19. Cutting Active Indicator Light 20. Torch Error Indicator Light 21. Error/Over Temperature Indicator Light Figure 3 © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05... -
Page 8: Symbols Chart
Positive Manual Air Test Mode Hertz (cycles/sec) Normal Cutting Duty Cycle Mode Perforated Plate Amperage Cutting Mode (Current) Torch Error Voltage Table 2 Cutting Active Single phase Inverter power source DC © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05... -
Page 9: Controls Explained
1. Rotate Amperage Knob (14) to desired amperage setting. NOTE: In most applications maximum amperage will work best. On very thin material or delicate applications you may wish to turn the amperage down. Figure 5 © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05... -
Page 10: Setting Air Pressure
Moist or dirty air will significantly reduce cut quality and consumable life. The CutForce CF-45P is supplied with a basic air filtration/moisture separator to assist with providing suitable air supply. The moisture separator is self-draining, the Air Filter Moisture Drain Tube (12) exits out the bottom of the clear Air Filter Bowl (11). -
Page 11: Error/Over Temperature Indicator Light
Continuous light means likely damaged or missing torch consumables or insufficient air pressure supply to the torch. Figure 10 4.7 Cutting Active Light The Cutting Active Light (19) illuminates when the cutting power circuit is activated. Figure 11 © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05... -
Page 12: Power & Compressed Air Supply
3. NEVER let your generator run out of fuel whilst the plasma cutter is plugged in. Following these Golden Rules will significantly reduce the risk of any damage resulting from generator power supply. © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05... -
Page 13: Compressed Air Requirements
The air regulator/filter supplied with the CF-45P machine provides the minimum level of filtration. However, we strongly recommend the WELDCLASS PLATINUM Z-20 high-performance air filter, available as an optional accessory from your Weldclass distributor. This attaches to the inlet of the existing regulator/filter and provides excellent filtration down to 1-micron. -
Page 14: Operating Environment
Adequate ventilation is required to provide proper cooling for the machine. Ensure that the machine is placed on a stable level surface where clean cool air can easily flow through the unit. © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05... -
Page 15: Basic Operation
6. Compressed air will continue to flow through the torch for several seconds after the cutting stops. In this post-flow mode, the arc can be restarted immediately by depressing the torch switch. Trigger Spacer Figure 12 © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05... -
Page 16: Distance From The Tip To The Work Piece
Note: The speeds given here are typical for best quality cuts. Your actual speeds may vary depending on material composition, surface condition, operator technique, etc. Air cutting typically produces a rough face on stainless steel and aluminium. © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05... -
Page 17: Piercing The Work Piece
To make a square-edged cut along an inside diameter of a circle, the torch should move counter clockwise around the circle. To keep the square edge along an outside diameter cut, the torch should travel in a clockwise direction. Figure 15 © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05... -
Page 18: Reducing Dross For Clean Cuts
Usually it will need to be removed by grinding. When cutting troublesome steel, it is sometimes useful to reduce the cutting speed to produce ‘low speed dross’. Any resultant clean up can then be accomplished by scraping, not grinding. © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05... -
Page 19: Accessories, Spare Parts & Circuit Diagrams
CF-45 8.1 Plasma Torch and Spares: The Plasma Torch supplied with the CF-45P is a Weldclass XPT-40 model. To view parts for this torch, see below table. Torch Parts Ref. Part No. Description WC-06033 Spacer WC-06032 Retaining Cap WC-06031 Swirl Ring WC-06029 Tip 0.9mm Pk5... -
Page 20: Plasma Torch Pin Configuration
Table 7 Rear Panel Air Regulator/Filter WC-06333 On/Off Switch Cable Clamp Fan Grill Fan WC-06264 Air Solenoid Valve WC-06332 Inductor Solenoid valve bracket Heat Sink Heat Sink Heat Sink IGBT Table 6 © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05... - Page 21 CF-45 Figure 17 © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05...
-
Page 22: Primary Schematic Circuit Diagram
8.5 Primary Schematic Circuit Diagram Figure 18 © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05... -
Page 23: Care & Maintenance
Use only genuine replacement parts. Do not use modified or non-genuine parts. 9.2 Storing the Plasma Cutter When not in use the machine should be stored in the dry, dust-free and frost-free environment. © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05... -
Page 24: General Guide To Plasma Cutting
In addition to this, this machine has a pilot arc controller system. If the main arc cuts out and the torch remains to be triggered, the pilot arc will reignite. This is useful for cutting discontinuous workpieces like mesh or grids. © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05... -
Page 25: Plasma Torch Parts Wear & Replacement
Damaged torch head It is also very important to only use genuine Weldclass consumables and parts for the plasma torch. They are engineered to suit the machine and non-genuine items may cause lack of performance, short life span, torch and machine damage and void warranty. -
Page 26: Troubleshooting
Material may be too thick for Several passes may be necessary capacity of plasma or find some other method to cut the material Worn torch parts Replace with new torch parts © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05... - Page 27 Extension cord being used is not Use a heavy duty extension cord while operating heavy duty (2.5mm Extension cord being used is too Remove extension cord or use long shorter one. © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05...
-
Page 28: Knowledge & Resources
3. Unplug before performing maintenance. Always unplug the plasma cutter from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. 4. Never leave the plasma cutter unattended while plugged into power. Turn power off before leaving the plasma cutter unattended. © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05... - Page 29 12. Do not use this machine for pipe thawing. This machine was not designed for pipe thawing and will be a significant electrical & heat hazard if attempt is made to use for thawing pipe. © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05...
-
Page 30: Plasma Cutting Safety Instructions & Warnings
CAUTION! Have the equipment serviced by a qualified repair person using identical replacement parts. This will ensure that the safety of the power tool is maintained. © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05... -
Page 31: Personal Safety
5. Never wear contact lenses while plasma cutting. 13.4.3 Noise Can Damage Hearing CAUTION! Noise from some processes can damage hearing. Use AS/NZS compliant ear plugs or ear muffs if the noise level is high. © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05... -
Page 32: Work Environment Safety
4. Disconnect input power before installing or servicing this equipment. Lock input power, disconnect switch open, or remove line fuses so power cannot be turned on accidentally. 5. Properly install and ground this equipment according to national, state, and local codes. © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05... -
Page 33: Fumes And Gases
1. Protect yourself and others from flying sparks and hot metal. 2. Do not operate where flying sparks can strike flammable material. 3. Remove all flammables within 10m of the plasma cutting site. © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05... -
Page 34: Sparks & Hot Metal
WARNING! Chipping and grinding causes flying metal, and as welds cool they can throw off slag. 1. Wear an AS/NZS approved face shield or safety goggles. Side shields are recommended. 2. Wear appropriate safety equipment to protect the skin and body. © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05... -
Page 35: Warranty
7. The cost of freight, transport or travel. It is the responsibility of the purchaser to deliver the product under warranty to the nearest relevant service agent or distributor. 8. Cost for repairs carried out by a party not approved by Weldclass to carry out repairs. 9. Accessories and attachments such as leads and torches. -
Page 36: Warranty Conditions
14.4 Warranty Conditions This is a repair and/or replacement warranty only and does not allow for a refund. Weldclass reserves the right to replace faulty product or parts covered under warranty with alternative / equivalent product or parts should the original unit become obsolete or unavailable. No other warranty is expressed or implied. - Page 37 CF-45 NOTES © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05...
- Page 38 © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05...
- Page 39 CF-45 © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05...
- Page 40 © Weldclass 2019 | E.&O.E. | Edition 1.0 2019.05...
Need help?
Do you have a question about the CutForce CF-45P and is the answer not in the manual?
Questions and answers