Advertisement
Quick Links
Advertisement
Related Manuals for Sun-Stream Evolve Mini EHS Far Infrared Sauna
Summary of Contents for Sun-Stream Evolve Mini EHS Far Infrared Sauna
- Page 1 ASSEMBLY MANUAL Evolve Mini EHS Far Infrared Sauna...
-
Page 2: Pre-Assembly Checklist
Pre-Assembly Checklist Selecting a suitable location For best results, please place your sauna on a flat level surface. Suitable locations could include the garage, bedroom, sunroom. The sauna can be placed on carpet, tiles, timber flooring or concrete. For outdoor placement please note that the sauna must go in a covered area to provide protection from direct rainfall, additionally the sauna must be protected by one of our Australian made covers to protect the warranty. - Page 3 Prepare & Position the Sauna Floor If you are assembling your sauna on a hard surface floor it is recommended that you apply the included adhesive felt pads to the bottom of the sauna floor. Place the sauna floor in the desired location. It is necessary to position the floor out from your walls for assembly and move the sauna following assembly.
- Page 4 Left Side Wall Place the Left Side Wall on your floor behind the sauna Floor Base. Front Wall Insert the Front Wall (with window) into the channel in the sauna Floor Base United Kingdom - 0800 86 11 841...
- Page 5 Front Wall Front Left Corner Connect the Left Side Wall to the Front Wall by raising the Front Wall approx 1/2" then sliding down to connect the 2 fasteners. Cinch the two walls together by applying pressure on the outside of the Side Wall with the inside of your knee.
- Page 6 Fasteners It may be be that your sauna's fasteners (Tab and Keyhole) are installed opposite to those pictured. In such a case, the Wall which slides up will be opposite to that shown. Guiding Rule: Always slide the Wall with the Tab fastener UP then DOWN on to the Wall with the Keyhole fastener.
- Page 7 Back Left Corner Repeat the procedure to connect the Back Wall to the Left Side Wall Raise the Wall will the Tab Fastener Back Wall approx 1/2" then slide down to connect the 2 fasteners. Cinch the two walls together by applying pressure on the outside of the Side Wall with the inside of your knee.
- Page 8 Back Right Corner Connect the Back Wall to the Right Side Wall Raise the Wall will the Tab Fastener approx 1/2" then slide down to connect the 2 fastenersl Cinch the two walls together by applying pressure on the outside of the Side Wall with the inside of your knee. Front Right Corner Repeat the procedure to connect the Right Side Wall to the Front Wall...
- Page 9 Connect the Front Wall heater electrical lead to the floor base. Ensure that the connector is fully inserted and that the threaded cuff is fully screwed onto the Floor Base connector. Under-Bench Electrical NOTE: Do not connect main power cord to your wall outlet at this time. United Kingdom - 0800 86 11 841...
- Page 10 Connect the circular connector to Attach the 'D-Sub' computer Power Supply Box. style connector as shown. Align the groove in connector to properly insert. Thread the cuff of the connector on fully. Plug in all heater leads to the receptacles in the Power Supply Box. Feed the main Power Supply Cord in through the hole in the Back Wall and insert in Power Supply Box.
- Page 11 Remove Side Wall Heater Guards The wooden lattice work in front of the heaters is referred to as the heater guard. These are held in place with strong magnets. It is necessary to remove the heater guards from the two side walls in order to install the leg heater and the sauna bench.
-
Page 12: Connecting The Ground Wire
Connecting the ground wire Install Bench Angle the Bench into place to clear the Side Wall window frames. The Bench installs foil side down. Connect the grounding wire from bottom side of Lower the Bench into Position Bench as shown United Kingdom - 0800 86 11 841... - Page 13 Ensure that 12V DC power line from the Roof (with white plastic connector) is accessible before installing the Roof. If you are unable to grab hold of the 12V power line from inside the roof it may be necessary to remove the first T&G board on the Roof (access panel) and feed the wire down through the hole in the roof.
- Page 14 Connect the 12 V power line between the Side Wall and Roof. Tuck the white plastic connector inside of the Roof and lower the Roof into place. It may be necessary to gently push on the inside or outside of the walls to align tops of walls with the Roof channel.
- Page 15 Heater Guards The heater guards in your new Sun Stream Infrared Sauna are held to the wall with strong earth magnets. If preferred, the heater guards can be screwed directly to the wall for a more permanent and secure attachment. The heater guards are pre-drilled for the attachment screws.
- Page 16 Drill a pilot hole into the wall through the holes in the heater guards.Do not drill deeper than necessary for the length of the screw. NOTE: The pilot holes are important to ensure that the tongue and groove wall boards do not split when installing screws.
-
Page 17: Cup Holder
Accessories Backrests Your new Sun Stream Sauna comes equipped with backrests constructed from Western Red Cedar. Position the backrest as pictured to provide lower back support and to position yourself a comfortable distance from the Infrared heater panels. Cupholder Many of our customers simply set the cup holder on the bench of the sauna.
Need help?
Do you have a question about the Evolve Mini EHS Far Infrared Sauna and is the answer not in the manual?
Questions and answers