Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Intermec EasyLAN 100I
Summary of Contents for Intermec EasyLAN 100I
-
Page 1: Ethernet Interface Board
Installation Instructions P/N 1-960475-00 Edition 1 May 2000 EasyLAN 100i Ethernet Interface Board... -
Page 2: Table Of Contents
4. Communication Setup Intermec EasyLAN 100i Installation Instructions Edition 1, May 2000 Part No. 1-960475-00 Intermec EasyLAN 100i – Installation Instructions Ed. 1 Table of Contents ... 1 Copyright Information ... 2 Trademarks ... 2 Description ... 3 Printer Firmware ... 3 Installation Kit ... -
Page 3: Copyright Information
Intermec Printer AB. © Copyright Intermec Printer AB, 2000. All rights reserved. Published in Sweden. The word Intermec, the Intermec logo, EasyCoder, EasyLAN, and Fingerprint are either trademarks or registered trademarks of Intermec Technologies Corp. -
Page 4: Description
Intermec EasyLAN 100i Ethernet network interface board to provide you with dependable service and advanced management capabilities. The printer must be fitted with Intermec Fingerprint v. 7.31 or later. The Ethernet port is addressed as device "net1:" (communication channel #5). -
Page 5: Physical Installation Easycoder Xp-Series
EasyCoder XP-Series #T10 Torx screws (4x) If the EasyLAN 100i interface board alredy is installed in your printer, please bypass this chapter and continue at chapter 3. This description applies to Intermec EasyCoder 501 XP and Intermec EasyCoder 601 XP only. - Page 6 Check that the board fits into the two square cut-outs on the left side of the slot. • Attach the EasyLAN 100i interface board to the printer's rear plate by means of two of the screws left over when you removed the original cover plate.
- Page 7 "uart1:" and the standard parallel interface "centronics:". Please continue at chapter 3 for instructions on how to establish communication with the TCP/ IP network. Intermec EasyLAN 100i – Installation Instructions Ed. 1 IC37 IC305 IC33...
-
Page 8: Easycoder F-Series
EasyCoder F-Series Intermec EasyLAN 100i – Installation Instructions Ed. 1 This description applies to Intermec EasyCoder F2 and Intermec EasyCoder F4 only. • Open the electronics compartment by removing the font/left-hand cover, which is held by three (3) #T20 Torx screws from the paper compartment side of the centre-line wall. - Page 9 • Insert the EasyLAN 100i interface board with the components side facing right, as seen from behind. • Attach the EasyLAN 100i interface board to the printer's rear plate by means of the two screws left over when you removed the original cover plate.
- Page 10 EasyCoder F-Series, cont’d. Intermec EasyLAN 100i – Installation Instructions Ed. 1 • Connect the flat cable included in the kit between connector P81 on the CPU board and connector P31 on the interface board. 1-971614-00 P02 BOOT STRAP SW10 R72 R73...
-
Page 11: Connection Connection Printer To Network
EasyLAN 100i interface board: • Using a category 5 unshielded twisted pair cable (or better), con- nect the EasyLAN 100i interface board to your Local Area Net- work (LAN). • Connect the power cord and turn on the power to the printer. -
Page 12: Communication Setup Assigning An Ip Address
This method is described in this chapter. • Remotely from the host computer. This method is described in the Intermec EasyLAN 100i User's Manual, which can be found in the CD-ROM included in the kit. Setting the IP address manually from the Setup Mode... - Page 13 • Similar to the IP address and netmask, enter the address of the default router (gateway), then press the Enter key. SETUP: NETWORK • Press the Setup key to leave the Setup Mode. Now the printer is logically connected to your local network (LAN). Intermec EasyLAN 100i – Installation Instructions Ed. 1...
-
Page 14: Setting The Ip Address Automatically From The Setup Mode
Setting the IP address automatically from the Setup Mode In addition to setting the IP address manually, as described above, there are three methods for making the network server automati- cally assign an IP address for your EasyLAN 100i printer. - DHCP - BOOTP... - Page 15 (LAN). Refer to next page for an overview of the parts of the Setup mode used in connection with setting up the EasyLAN 100i interface board. A full description of the Setup Mode can be found in the Installation &...
-
Page 16: Reading An Assigned Ip Address
Reading an Assigned IP Address Intermec EasyLAN 100i – Installation Instructions Ed. 1 If you want to read an IP address that has already been assigned – either manually or automatically – without changing any settings, proceed as follows: • Press the Setup key on the printer's built-in keyboard. This mes-... -
Page 17: Setup Mode Overview
IP address. The diagram below illustrates the hierachy of setup options that are added to the Setup Mode when an EasyLAN 100i interface board is installed in the printer. Like most other options in the Setup Mode, these options can be changed using setup strings and files or read using SETUP WRITE statements. -
Page 18: Printing Test Label #6
• Press the F5 key repeatedly until the display shows: <ENTER> = PRINT: <F5> = NEXT #6 • Press the test button on the rear plate of the EasyLAN 100i inter- face board and keep it depressed while pressing Enter on the printer's keyboard. The test label is printed. -
Page 19: Checking The Communication
IP address. It will, for exam- ple, look like this: Refer to the Intermec EasyLAN 100i User's Manual included on the CD-ROM that comes with the kit for explanations of how to use the home page to set up the printer, control the communication, and manage the printing.