Table of Contents
Advertisement
Track Runner Series – Cheat Sheet
MODE
Function
0, 1, 6
None, Track Runner is stopped
2
Manual REVERSE slow (no DMX needed)
3
Manual reverse fast (no DMX needed)
4
Manual FORWARD slow (no DMX needed)
5
Manual forward fast (no DMX needed)
7
Positioning with slow ramp
8
Positioning with medium ramp
9
Positioning with fast ramp
Before each use
− Inspect the product for damage, wear, corrosion or abuse.
− Inspect the moving portion for damage, wear, corrosion or abuse and make sure everything
− Check that the unit is securely mounted according to the user manual.
WARNING! Do use the product if any damage is found
Green LED indicators:
LED next to the DMX address selectors.
Glows constant:
DMX connection is correct.
Flashing:
DMX signal is missing.
LED next to the MODE selectors.
Fast flashing:
The motor needs to be reset, before it can be used.
Slow flashing:
The motor is moving towards the set position
Steady light:
The set position has been reached and the motor stopped.
How to get started
1. Manually feed mains power to the unit and roll-on a secured track using mode 2 from the right side or mode 4
for from the left side (seen form the connections).
2. Apply DMX from a Lighting desk, ideally a desk with manual faders.
3. Make sure that your six channels are patched from DMX channel 1 to 6.
4. Pull all channels on to 0%
5. Apply power to the track and link the wireless DMX units by pressing (short push<½s) the LINK SW on both
transmitter and receiver within 10s –
after the 10s (timeout of wireless search function) or use the hard wiring through a cable carrier.
6. Set DMX channel 6 to 53% -
Pull channel 4 to 20 % -- the unit starts moving reverse (left).
7.
8.
Stop the unit (pull channel 4 to 0%) when the desired LEFT end position is reached.
Pull channel 5 to 20 % -- the unit starts moving forward (right).
9.
10. Stop the unit (pull channel 5 to 0%) when the desired RIGHT end position is reached.
11. Pull channel 1 (position) to 75 %
12. Pull channel 3 (speed) to 50% -
13. Pull channel 1 (position) to 25% - T
Tech specs:
General
Maximum speed
Slow motor 23 cm/s (9.1 in/s)
Fast motor 42 cm/s (16.5 in/s)
Load capacity
50 kg (110 lb)
Push capacity
500 kg (1102 lb)
Weight
10.8 kg (23.8 lb)
352-353.805.006
is safely attached and within the maximum loads.
RF LINK, LINKED, STATUS(STAT) and DMX lamp should be lit when connected
This enables the saving of soft-limit left and right position.
The unit start to move reverse, with 50% speed, to a position that is 75%.
he unit starts to move forward, with 50% speed, to a position that is 25%
DMX Ch.
Function
1
Position rough (Hi of a 16-bit DMX channel)
2
Position fine (Lo of a 16-bit DMX channel)
3
Set the maximum speed
4
Set soft-limit REVERSE position, or move manually
5
Set soft-limit FORWARD position, or move manually
6
51-54% Save soft limit
Else
Save soft limit
Individual LED's next to the antenna.
20-80%:
RF Link:
Linked:
DMX:
STAT:
Wireless
2.4 GHz ISM Band / 100mW (CRMX inside)
LINK SW:
Short-push (<½s)
Link to transmitter/receiver
Long-push (>3s)
Unlink from transmitter (Change transmitter station)
32
Enabled
Disabled
Indicates signal strength of linked transmitter.
Active radio link is available.
Receiver linked to transmitter.
DMX signal is present.
Steady light indicates radio link and DMX
present.
Date: 2019-07-02
Advertisement
Table of Contents
