Programming Instructions; Setting The Date And Time - Ecowood TROLLEY Installation, User’s And Maintenance Handbook

TROLLEY
UK
• The hot air fan comes on automatically about 15 minutes after ignition, at the first speed,
and levels itself at the selected power for the normal operating cycle, 25 minutes after
ignition.
• It is possible to adjust the hot air fan separately from fuel loading rate (only for the first
two power levels); the two functions are currently set proportionately by the manufac-
turer.
• To switch off the stove completely just press the ON/OFF button again; after the flame has
gone out the stove will remain in operation for about 20 minutes until all the internal
parts have cooled down.
IMPORTANT
Continuous operation of the stove at maximum power could shorten the life of the electronic and
mechanical components, and also reduce safety.
The stove is able to operate continuously for long periods of 10/15 hours if the selected pellet load-
ing power level does not exceed the third position.
Using the stove at the fourth or fifth loading rate for long periods will reduce safety, therefore an au-
tomatic power limiting device has been installed as standard in the stove.
If the automatic power limiting device is disabled at the user's request (this should be done
by the installer technician following an evaluation of the conditions under which the stove
is to be used), it is necessary to connect the stove to the flue gas exhaust system using stain-
less steel pipes, or pipes painted with airtight seals. If the fourth power level is selected we
advise operating the stove continuously at this level only if it is alternated hourly with op-
eration at lower load rates, while the fifth level should only be used continuously for a max-
imum of 30 minutes.
ATTENTION:
During operation, changing the function between MAN and AUTO will be treated as a new
command for initial ignition, therefore the stove will re-activate the start cycle for 25 min-
utes.
NOTE: the functions on the remote control are identical.
To switch on by phone
To switch on by phone, as the main board will allow,
it is necessary to connect a modem (optional).
34

PROGRAMMING INSTRUCTIONS

The fire must be extinguished when the clock and automatic ON/OFF cycles are programmed in
the stove.
1. To enter programming, press the ON/OFF and MAN/AUTO buttons one after the other and keep
them both pressed for a few moments, then release them together.The display will show the
message PR.
2. Press the + button followed by the ON/OFF and MAN/AUTO buttons one after another, so that
time is displayed.
3. Press the - button followed by the ON/OFF and MAN/AUTO buttons one after another, to dis-
able the time display.
4. Press MAN/AUTO to set the clock.
5. Press ON/OFF to set the automatic ON/OFF cycles for the stove.
6. To exit programming, press ON/OFF and then MAN/AUTO immediately afterwards.

SETTING THE DATE AND TIME

1. To enter programming, press the ON/OFF and MAN/AUTO buttons one after the other and keep
them both pressed for a few moments, then release them together.The display will show the
message PR.
2. Press MAN/AUTO to set the clock (the first digit on the left in the "H" display will flash).
3. Press the + button to increase the flashing value; if you press the - button you will shift to
the previous display.
4. To enter and confirm each setting, press the ON/OFF button; every time you confirm a setting
the next display will start to flash.
Continue programming the settings for the hour "H" and minutes "M" and then programme
the current day of the week "D" (e.g. 1=Monday; 2=Tuesday; 7=Sunday).
When you have finished programming (after selecting the last number on the right in the "D"
display, the message PR will reappear.
5. To exit programming, press ON/OFF and then MAN/AUTO immediately afterwards.
PROGRAMMING AUTOMATIC ON AND OFF TIMES
1. To enter programming, press the ON/OFF and MAN/AUTO buttons one after the other and keep
them both pressed for a few moments, then release them together.The display will show the
message PR.
TROLLEY
UK
35