Related Manuals for Fisher & Paykel DW60UT4I2
Summary of Contents for Fisher & Paykel DW60UT4I2
- Page 1 BUILT-UNDER DISHWASHER INTEGRATED DW60UT4I2, DW60U4I2, DW60U2I2, DW60UT6I2 models INSTALLATION GUIDE NZ AU UK IE...
-
Page 3: Safety And Warnings
SAFETY AND WARNINGS WARNING! WARNING! Electric Shock Hazard Cut Hazard Failure to follow this advice may result in Failure to use caution could result in injury. electrical shock or death. • Take care – panel edges are sharp. • This appliance must be earthed. This appliance has a cord with an equipment-earthing conductor WARNING! and an earthing plug. - Page 4 SAFETY AND WARNINGS WARNING! Installation must comply with your local building and electricity regulations. Failure to install the custom panels correctly could invalidate any warranty or To reduce the risk of fire, injury to persons or damage when using the appliance, follow the liability claims.
-
Page 5: Components Required
COMPONENTS REQUIRED PARTS TOOLS Keep all packing materials until the unit has been inspected. Not supplied Not supplied Inspect the product to ensure there is no shipping damage. If any damage is detected contact the dealer or retailer you bought the product from to report the damage. Fisher &... -
Page 6: Product Dimensions
PRODUCT DIMENSIONS DW60UT4I2 DW60U4I2 PRODUCT DIMENSIONS (MM) (MM) A Overall height* 857 - 917 820 - 880 B Overall width** C Overall depth** D Height of chassis E Depth of chassis PLAN F Height of feet* 0 - 60 0 - 60 G Depth of toe kick recess... -
Page 7: Custom Panel Dimensions
Toe kick considerations Depending on the desired toe kick recess depth and door panel extension, the toe kick panel height may need to be adjusted to allow adequate door swing. PROFILE DW60UT4I2 DW60U4I2 CUSTOM PANEL CONSIDERATIONS (MM) (MM) A Minimum height of custom door panel for full coverage of the... - Page 8 CLEARANCES Connections can be located in an adjacent cabinet on either side of the dishwasher*** PLAN ISOMETRIC DW60UT4I2 DW60U4I2 CABINETRY DIMENSIONS CABINETRY CLEARANCES (MM) (MM) A Minimum inside height* A Minimum clearance to adjacent cupboard door B Minimum inside width...
-
Page 9: Left Side
PLUMBING & ELECTRICAL CONSIDERATIONS Hose and cord lengths Your services can be installed to either the left-hand or right-hand side of the product in an adjacent cabinet. Refer to 'Cabinetry preparation' for service access requirements. The drain hose should not extend more than 4m. A longer drain hose will cause reduced performance. -
Page 10: Service Access
SERVICE ACCESS We recommend locating the service holes on either side of the Dishwasher as shown. If the holes are created through wood, ensure the edges are smooth and rounded If the holes are created through metal, ensure an edge protector is fitted. REAR WALL FLOOR... - Page 11 UNPACK PRODUCT CABINETRY PREPARATION Ensure all minimum cabinetry and Cut straps, lift carton off product and service specifications have been met remove the top cap. and that all services will be accessible Dispose of packaging responsibly. after installation. Ensure cabinetry floor is free from Remove the install kit, any internal bumps and obstructions that could packaging, all rubber bands and all tape.
- Page 12 DOOR PANEL PREP PUSH INTO CAVITY Using a flat bladed screwdriver, turn to raise the leveling feet. Level the rear, Ensure door panel meets all outside legs first followed by the front specifications. legs. Do not adjust the rear middle leg yet.
- Page 13 SECURE DOOR PANEL FIT EXIT VENT Measure the custom panel overhang Align the door panel to the product. from the base of the inner door. Slot slider bracket and upper screws into place. Slide the panel upwards to Refer to the table below for the lock into place.
- Page 14 BALANCE DOOR SECURE TO CAVITY Use a 4mm Allen key to adjust the door tension. Rotate clockwise to increase tension, rotate Loosely fit 2 x side fixing screws. counterclockwise to decrease tension. Ensure both sides are adjusted evenly. Open the door at a 45° angle and If needed, adjust the Dishwasher within ensure it holds.
- Page 15 INSTALL SOUND SEAL & TOE KICK FIT SOUND SEAL CUSTOM TOE KICK PANEL Mark the pilot hole locations for each bracket. Measure the centre of the panel and mark 237mm to each side. Align both sound seal sheets to the To determine the height of the base of the dishwasher.
- Page 16 PLUMBING & ELECTRICAL CONNECTION Ø38MM STANDPIPE INSTALLATION SINK TRAP/WASTE TEE INSTALLATION Install the drain hose support to the Install the drain hose support to the back wall, as close to the underside of back wall, as close to the underside of the countertop as possible.
-
Page 17: Installer Checklist
INSTALLER CHECKLIST TEST OPERATION TO BE COMPLETED BY THE INSTALLER Installation … Check all parts are installed correctly and are secure. Turn power and water supply on and open the dishwasher. … Ensure all packaging, tape and rubberbands have been removed. …... - Page 20 FISHERPAYKEL.COM © Fisher & Paykel Appliances 2022. All rights reserved. The models shown in this guide may not be available in all markets and are subject to change at any time. The product specifications in this guide apply to the specific products and models described at the date of issue.
Need help?
Do you have a question about the DW60UT4I2 and is the answer not in the manual?
Questions and answers