Summary of Contents for Fisher & Paykel OR30SCG4R1
Page 1
Setting the Pressure Regulator The pressure regulator is accessible by removing the storage/warmer drawer; the pressure regulator is positioned on the rear right side of the range C. https://producthelp.fisherpaykel.com/us/Cook/Ranges/Gas/OR30SCG4R1/Installation_Guide_OR30SCG4R1/19_Gas_Conver… Updated: Thu, 02 Dec 2021 09:44:40 GMT Powered by...
Page 2
• Do not remove storage/warming drawer during operation. • Be sure storage/warming drawer is empty before removing. • Always position your hand below the front panel to open/close the drawer. https://producthelp.fisherpaykel.com/us/Cook/Ranges/Gas/OR30SCG4R1/Installation_Guide_OR30SCG4R1/19_Gas_Conver… Updated: Thu, 02 Dec 2021 09:44:40 GMT Powered by...
1800 Propane Gas) Semirapid (SR) 8000 (Natural 1800 Gas) Inner 2800 1100 crown Dual Full 18000 6500 79 (x2) 135 (x2) burner OR30 Gas Models Only Oven burner 14000 2400 https://producthelp.fisherpaykel.com/us/Cook/Ranges/Gas/OR30SCG4R1/Installation_Guide_OR30SCG4R1/19_Gas_Conver… Updated: Thu, 02 Dec 2021 09:44:40 GMT Powered by...
Page 4
• Refit the flame spreaders, the burner caps and the pan supports. The burners are designed so that no regulation of the primary air is required. Semi-rapid burner Dual burner https://producthelp.fisherpaykel.com/us/Cook/Ranges/Gas/OR30SCG4R1/Installation_Guide_OR30SCG4R1/19_Gas_Conver… Updated: Thu, 02 Dec 2021 09:44:40 GMT Powered by...
Page 5
LO position (minimum rate of outer crown and maximum rate of inner crown). • Remove the dial. • With a thin screwdriver, turn the regulation screw inside the tap rod until adjustment is correct. For LP/PROPANE gas, tighten the adjustment screws completely https://producthelp.fisherpaykel.com/us/Cook/Ranges/Gas/OR30SCG4R1/Installation_Guide_OR30SCG4R1/19_Gas_Conver… Updated: Thu, 02 Dec 2021 09:44:40 GMT Powered by...
Page 6
Regulation screw (Semi-Rapid burner) Regulation screw (Inner crown of dual burner) Regulation screw (Outer crown of dual burner) Gas Conversion (gas gas models only) Replacing the Lower Oven Burner Injector https://producthelp.fisherpaykel.com/us/Cook/Ranges/Gas/OR30SCG4R1/Installation_Guide_OR30SCG4R1/19_Gas_Conver… Updated: Thu, 02 Dec 2021 09:44:40 GMT Powered by...
Page 7
4. Using a 9/32” (7mm) box spanner, unscrew the injector and replace it with a new one selected in accordance with the ‘Injectors table’. 5. Replace the burner and other components. https://producthelp.fisherpaykel.com/us/Cook/Ranges/Gas/OR30SCG4R1/Installation_Guide_OR30SCG4R1/19_Gas_Conver… Updated: Thu, 02 Dec 2021 09:44:40 GMT Powered by...
Page 8
1/8–5/32” (3–4mm) in height. The flame should not go out even when passing suddenly from maximum to minimum flame. For LP/PROPANE gas the by-pass screw must be fixed thoroughly. https://producthelp.fisherpaykel.com/us/Cook/Ranges/Gas/OR30SCG4R1/Installation_Guide_OR30SCG4R1/19_Gas_Conver… Updated: Thu, 02 Dec 2021 09:44:40 GMT Powered by...