Icom IC-756PROII Instruction Manual page 82

13
CONTROL COMMAND
• Command table (continued)
Command Sub command
0E A1–A7
0F
10
11
12
13
14 01 + Level data [AF] level setting (0=max. CCW to
02 + Level data [RF] level setting (0=max. CCW to
03 + Level data [SQL] level setting (0=11 o'clock to
06 + Level data [NR] level setting (0=min. to
07 + Level data Inside [TWIN PBT] setting or IF
08 + Level data Outside [TWIN PBT] setting
09 + Level data [CW PITCH] setting (0=low pitch to
0A + Level data [RF POWER] setting (0=mini. to
0B + Level data [MIC GAIN] setting (0=mini. to
0C + Level data [KEY SPEED] setting (0=slow to
0D + Level data [NOTCH] setting (0=low freq. to
0E + Level data [COMP] setting (0=mini. to
0F + Level data [BK-IN DELAY] setting (0=short
10 + Level data [BAL] level setting (0=max. CCW,
15
80
Description
Set ∂F scan span (A1=±5 kHz,
A2=±10 kHz, A3=±20 kHz,
A4=±50 kHz, A5=±100 kHz,
A6=±500 kHz, A7=±1 MHz)
B0 Set as non-select channel
B1 Set as select channel
D0 Set scan resume OFF
D3 Set scan resume ON
00 Turn the split function OFF
01 Turn the split function ON
00 Select 10 Hz (1 Hz) tuning step
01 Select 100 Hz tuning step
02 Select 1 kHz tuning step
03 Select 5 kHz tuning step
04 Select 9 kHz tuning step
05 Select 10 kHz tuning step
06 Select 12.5 kHz tuning step
07 Select 20 kHz tuning step
08 Select 25 kHz tuning step
00 Attenuator OFF
06 Attenuator ON (6 dB)
12 Attenuator ON (12 dB)
18 Attenuator ON (18 dB)
00 Select/read antenna selection
01 (00=ANT1, 01=ANT2 : Add 0 or 1
to turn [RX ANT] OFF or ON, re-
spectively.)
00 Announce with voice synthesizer
01 (00=all data; 01=frequency and
02 S-meter level; 02=receive mode)
255=max. CW)
255=11 o'clock)
255=max. CW)
255=max.)
shift setting (0=max. CCW,
128=center, 255=max. CW)
(0=max. CCW, 128=center,
255=max. CW)
255=high pitch)
255=max.)
255=max.)
255=fast)
255=high freq.)
255=max.)
delay to 255=long delay)
128=center, 255=max. CW)
01 Read squelch condition
02 Read S-meter level
Command Sub command
16 02
12
22
40
41
42
43
44
45
46
47
48
49
19 00
1A 00
01
02
03
04
0501
0502
0503
0504
0505
0506
0507
0508
0509
0510
0511
0512
0513
0514
0515
0516
0517
Description
Preamp (0=OFF; 1=preamp 1;
2=preamp 2)
AGC selection (1=Fast; 2=Mid;
3=Slow)
Noise blanker (0=OFF; 1=ON)
Noise reduction (0=OFF; 1=ON)
Auto notch (0=OFF; 1=ON)
Repeater tone (0=OFF; 1=ON)
Tone squelch (0=OFF; 1=ON)
Speech compressor (0=OFF; 1=ON)
Monitor (0=OFF; 1=ON)
VOX function (0=OFF; 1=ON)
Break-in (0=OFF; 1=semi break-
in; 2=full break-in)
Manual notch (0=OFF; 1=ON)
RTTY filter (0=OFF; 1=ON)
Read the transceiver ID
Send/read memory contents (see
p. 82 for details)
Send/read band stacking register
contents (see p. 82 for details)
Send/read memory keyer con-
tents (see p. 82 for details)
Send/read the selected filter width
(0=50 Hz to 40/31=3600/2700 Hz)
Send/read the selected AGC time
constant (0=OFF, 1=0.1/0.3 sec. to
13=6.0/8.0 sec.)
Send/read SSB TX Tone (Bass)
level (0 =min. to 10=max.)
Send/read SSB TX Tone (Treble)
level (0=min. to 10=max.)
Send/read MONITOR gain (0=min.
to 255=max.)
Send/read CW side tone gain
(0=min. to 255=max.)
Send/read CW side tone gain limit
(0=OFF, 1=ON)
Send/read beep gain (0=min. to
255=max.)
Send/read beep gain limit (0=OFF,
1=ON)
Send/read LCD contrast (0=0% to
255=100%)
Send/read LCD backlight (0=0% to
255=100%)
Send/read LCD horizontal position
(0=1 to 7=8)
Send/read switch backlight (0=1 to
7=8)
Send/read display type (0=A, 1=B,
2=C, 3=D, 4=E, 5=F, 6=G, 7=H)
Send/read display font (0=Basic1,
1=Basic2, 2=Pop, 3=7seg,
4=Italic1, 5=italic2, 6=Classic)
Send/read memory name (0=OFF,
1=ON)
Send/read my call setting (10-char-
acter: see p. 82)
Send/read current time (0000 to
2359)
Send/read power-ON timer set
(0000 to 2359)