Page 1
Product Manual NRD - 1300, 1600 Radial Drilling Machine 1. Please make sure to read the product manual before use. 2. The operator should have full knowledge of the manual before use. 3. The said product has been manufactured according to the Korea...
4-9 Arm 4-10 Electric Control Box 4-11 Arm Elevation Box 4-12 Tool Ejector Transportation and Installation of Product 5-1 Transportation & Unloading Method of Product 5-2 Wiring 5-3 Product Installation 5-4 Balance of Product 5-5 Oil Supply Nambuk Co., Ltd.
Page 3
Products Manual NB19-E01 NRD-1600,1300 Product Operation 6-1 Power Input of Product 6-2 Rotational Direction of Spindle 6-3 Feed of Spindle 6-4 Ascending & Descending of Arm 6-5 Column & Head Clamp 6-6 Selection of Spindle Revolution 6-7 Rotational Direction of Spindle 6-8 Change of Feed Speed 6-9 Auto-feed of Spindle 6-10 Micro Feed of Spindle...
If the user operates or repairs the machine without full knowledge of the manual, there is a risk of machine/personal accidents. Besides, there is a detailed explanation of the basic cautions about safety in a later section. Please make sure to read them and gather full knowledge of them. Nambuk Co., Ltd.
A condition if the user of this machine or the third person can neither operate it Information to pay attention to during the correctly nor avoid such a situation leading use of this machine to death, fatal injury, or property damage on the equipments Nambuk Co., Ltd.
Do not approach Injury by rotation Do not disassemble Prohibited tool Scattering Do not use gloves Caution Full knowledge of Jammed in gears (Danger product manual Warning) Enforced Fire Grounding Jammed in belt Caution General caution Electrical risk Nambuk Co., Ltd.
Full knowledge of product manual When controlling the machine, please make sure to have full knowledge of the product manual. work without full knowledge, cause accident/failure due to improper operation. Please immediately contact us for loss or damage. Nambuk Co., Ltd.
9. Please do not remove the protection device. If you work after removing the protection device, it may cause serious disaster. 10. If you have any other questions regarding safety control, please inquire us. ▮ Label Number: PL-02 Nambuk Co., Ltd.
Page 9
착용 하십시오. 경 고 보호장비 착용 경 고 비산물과의 접촉은 부상의 위험과 실명 을 유발할수 있습니다 . 중량물 취급주의. 경 고 경 고 있으니 운반장치나, 2인 이상이 작업하십시오. 말릴 위 험 서비스전에 주 전원 차단 및 잠금장치를 체결하십시오. Nambuk Co., Ltd.
Please do not touch the tools or chips Please work on the processed object while the spindle is rotating. after gripping it firmly with a vise. Nambuk Co., Ltd.
Page 11
If the safety covers (belt cover and gear cover) of the machine are damaged or lost, please contact us and make sure to use the machine after attaching them. Nambuk Co., Ltd.
Page 12
Wear a safety Wear safety protection helmet goggles guard Please do not remove the protection uard. During work, make sure to wear If you work after removing the protection protective gear. guard, serious disaster may occur. Nambuk Co., Ltd.
Range of spindle feed speed mm/rev 0.07~1.0 0.07~1.0 Spindle drive motor Arm elevation motor Motors Clamping motor Coolant pump Tool ejection motor(Power pack) 5 0 0 6 5 0 4 0 0 고 정 너 트 - T N2 2 Nambuk Co., Ltd.
As the spindle sleeve has been processed through heat treatment grinding Chrome-Molybdenum steel, its durability and wear resistance is excellent to maintain the precision of this machine for a long period. Nambuk Co., Ltd.
Pilot Lamp will light up. If the lamp is not lit, please connect by switching two of the three lines. Please make sure to ground to the earth at the ground mount. Nambuk Co., Ltd.
For the foundation, please increase or decrease the thickness of the concrete according to the ground in order to prevent sinking or generating cracks due to the weight of the machine and processed object. For the installation area, please avoid direct sunlight and install without any vibration. Nambuk Co., Ltd.
Page 19
The rotation of the arm should be within the range of 90 ˚ (+45 to 45 ) shown below. ˚ – ˚ • There is a risk that the machine will be overturned. • Machining should be done within the base of the body. Nambuk Co., Ltd.
Please supply with oil for other oil supply inspect the oil supply status periodically and sites according to the daily oil supply table manage according to the daily oil supply table. and oil supply sites diagram. Nambuk Co., Ltd.
Page 21
As each oil’s life is affected by many factors such as change of viscosity resulting from the conditions of use, environment (temperature, humidity, etc.), and oil deterioration, be sure to determine the exchange period after checking the oil conditions. capacity NRD-1300(25L), 1600(40L) * COOLANT TANK Oil Supply Sites Diagram Nambuk Co., Ltd.
(release of arm clamp) and the arm will rotate in reverse. descend. If the mono lever switch is placed at the middle position, descension will stop and screws will rotate at a fixed velocity in the opposite direction to clamp the arm. Nambuk Co., Ltd.
→ ← altered velocity. column sleeve clamped, left/right movement of the spindle box is possible. Please make sure to place the forward/reverse lever at the middle position (position Ⓘ ) for altering velocity, control spindle transmission lever. Nambuk Co., Ltd.
0.07, 0.13, and 0.23 and it is possible to change the feed speed to 6-speed. The feed speed is the amount of feed per one rotation of the spindle. Nambuk Co., Ltd.
Clauses 5-9. If feeding is completed as much as the selected depth, the auto feed lever will return to its original position auto feed will stopped. Nambuk Co., Ltd.
Please adjust the multi-disk clutch to slip at the current of the ammeter above 9A. As an exception, if the friction force of the multi-disk clutch is adjusted too strong, it may cause damage to the machine due to generation of overload. Nambuk Co., Ltd.
2. Set the external control handle at the bottom of column to OFF. 3. Please make sure to cut off the main power during machine repair, and repair after inserting a lock device key in the MAIN BREAKER switch. Nambuk Co., Ltd.
S u r g e p r o t e c t i o n p r o v i d e d a t m a c h i n e s u p p l y t e r m i n a l s 10-2 Protection Guard Manufacturing Diagram Nambuk Co., Ltd.