The AEL (accessible emission level )of the laser power output is less than CLASS 1 but the laser component is capable of emitting radiation exceeding the limit for CLASS 1. A specially instructed person should do servicing operation of the apparatus. AVH-P6300BT/XNUC...
Page 3
CAUTION Danger of explosion if battery is incorrectly replaced. Replaced only with the same or equivalent type recommended by the manufacture. Discord used batteries according to the manufacture's instructions. AVH-P6300BT/XNUC...
Page 4
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. AVH-P6300BT/XNUC...
Do not insert it reversely. 13. The part listed below is difficult to replace as a discrete component part. When the part listed in the table is defective, replace whole Assy. Monitor Unit IC5701 TK61222CQ6 Heat pad AVH-P6300BT/XNUC...
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting temperatures (hard to melt/easy to harden). The following lead-free solders are available as service parts: Parts numbers of lead-free solder: GYP1006 1.0 in dia. GYP1007 0.6 in dia. GYP1008 0.3 in dia. AVH-P6300BT/XNUC...
2. SPECIFICATIONS 2.1 SPECIFICATIONS • AVH-P6300BT/XNUC MP3 decoding format ...MPEG-1 & 2 Audio Layer 3 General WMA decoding format ..Ver. 7, 7.1, 8, 9, 10, 11, 12 Power source......14.4 V DC (10.8 V to 15.1 V (2 ch audio) allowable) (Windows Media Player) Grounding system....Negative type...
Page 9
Middle East Asian and South African models Frequency response....5 Hz to 44 000 Hz (with DVD, at sampling frequency Note 96 kHz) Specifications and the design are subject to mod- Signal-to-noise ratio....96 dB (1 kHz) (IEC-A net- ifications without notice. work) (RCA level) AVH-P6300BT/XNUC...
2.3 PANEL FACILITIES • AVH-P6300BT/XNUC Head unit CAUTION Use an optional Pioneer USB cable (CD-U50E) to connect the USB audio player/USB mem- ory as any device connected directly to the unit will protrude out from the unit and may be dangerous.
Page 11
SD memory card SEEK) slot CAUTION Use an optional Pioneer USB cable (CD-U50E) to connect the USB audio player/USB mem- ory as any device connected directly to the unit will protrude out from the unit and may be dangerous.
Page 12
Press to stop play- REAR SRC sources. back. Press and hold to turn the rear source off. Press to select the next/previous folder. Press to recall radio /(FOLDER/P.CH) station frequencies as- signed to preset tun- ing keys. AVH-P6300BT/XNUC...
Volume PCB Unit Keyboard PCB Switch PCB Unit Panel PCB Mother PCB Main PCB Unit BT PCB BT ANT PCB A:AVH-P6300BT/XNUC Unit Number : YWX5010 Unit Number : B:AVH-P6350BT/XNRD Unit Name : DVD Core Unit(MS7) Unit Name : Main PCB Unit...
DVD Mechanism Module and Drive Unit Grease GEM1043 DVD Mechanism Module and Drive Unit Bond GEM1033 DVD Mechanism Module Bond GEM1068 DVD Mechanism Module Grease GEM1011 Drive Unit Grease GEM1047 Drive Unit Grease GEM1071 Drive Unit Grease GEM1072 Drive Unit AVH-P6300BT/XNUC...
Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools: Portions to be cleaned Cleaning tools DVD pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008 Portions to be cleaned Cleaning tools Fans Cleaning paper : GED-008 AVH-P6300BT/XNUC...
4.1 OVERALL CONNECTION DIAGRAM Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or "ELECTRICAL PARTS LIST". S/PDIF IP-BUS NAVI INTER A : AVH-P6300BT/XNUC B : AVH-P6350BT/XNRD JA481 C : AVH-P6350BT/XNRI CKN1050-A ANGLE...
DDCCLK <- Clock Out DDCCLK : Pin92 (Frequency of 370 kHz) VD5 <- H VD5 : Pin113 VD8 <- H VD8 : Pin114 Starts Communication with Display microcomputor Source Keys operative Source ON SYSPW : Pin130 SYSPW <- H AVH-P6300BT/XNUC...
To “Replace pickup” Check 3 Check measured value of error ratio * Make sure to avoid any unwiped spots or actuator breakage. Check error ratio Lens cleaning Clean lens Within prescribed completed? value? To “Replace pickup” No problem found in pickup AVH-P6300BT/XNUC...
Page 38
Remarks: LD current value (ref.) GGV1025 DVDLD1-VCC5_3 60~390(mV) 10~65(mA) DVDLD1 VCC5_3 Disc used Spot to check Rated value Remarks: LD current value (ref.) TCD-782 CDLD1-VCC5_3 60~360(mV) 10~60(mA) VCC5_3 CDLD1 Mind breakage of a laser diode caused by static electricity. AVH-P6300BT/XNUC...
Page 39
Check the error ratio of a specified ID in the tracking closed status in the test mode. Disc used Spot to check Rated value Remarks: GGV1025 ID : 40000 1.000E-3 or less GGV1025 ID : 200000 1.000E-3 or less TCD-782 ID : Home position 2.500E-3 or less Error ratio: 0.742E-5 in this case AVH-P6300BT/XNUC...
IC but Go to FE Check a core unit (as no key or others is written in a flash alone). Normal? Go to FE Check Go to FE-related FE part normal? repair Replace unit Normal? AVH-P6300BT/XNUC...
Page 41
Check the voltage of the sending pin when the power is ON. Checking should be based on DGND. Spot to check Module NO. Rated value Unit 1 STANDBY-DGND1 VCC33-0.6V or more PCB side A STANDBY DGND1 Fig. 1.1: Spots to check in STANDBY AVH-P6300BT/XNUC...
Page 42
Unit 1 VDD5_2 - DGND1 5.0 ± 0.4 2 VCC33_1 - DGND1 3.3 ± 0.15 3 VCC12-1 - DGND1 1.2 ± 0.12 PCB side A VCC12-1 VDD5_2 VCC33_1 DGND1 Fig. 2.2: Spots to check in VDD5, VCC33, VCC12 voltages AVH-P6300BT/XNUC...
Page 43
Check the voltage of the sending pin when the power is ON. Checking should be based on DGND. Spot to check Module NO. Rated value Unit 1 NRES-DGND1 VCC33 x 0.7 or more PCB side A NRES DGND1 Fig. 3.1: Spots to check in RESET AVH-P6300BT/XNUC...
Page 44
Check the voltage of the sending pin when the power is ON. Checking should be based on DGND. Spot to check Module NO. Rated value Unit 1 VSENS - DGND1 VCC33 x 0.7 or more PCB side A DGND1 VSENS Fig. 4.2: Spots to check in VSENS AVH-P6300BT/XNUC...
Page 45
Spot to check Module NO. Rated value Unit 1 IC1501 156pin 27 MHz ± 50ppm Rated value Fig. 5.2: Rated value of a clock PCB side A DGND1 IC1501 156pin Fig. 5.3: Spots to check in 27 MHz AVH-P6300BT/XNUC...
Page 47
PCB side B Spot to check 1 (IC1480) PCB side A Spot to check 2 (IC1501) Fig. 6.2: Spots to check in SDRAM I/F AVH-P6300BT/XNUC...
Page 48
Rated value Unit 1 VD8_1 - PGND3 8.0 ± 0.4 2 VD - PGND_3 8.0 ± 0.4 3 VCC5_1 - AGND1 5.0 ± 0.1 PCB side A VD8_1 PGND3 AGND1 VCC5_1 Fig. 7.2: Spots to check in VD8, VCC5 voltages AVH-P6300BT/XNUC...
Page 49
Checking should be based on PGND, AGND. Spot to check Module NO. Rated value Unit 1 VD - PGND_3 8.0 ± 0.4 2 AVCC5 - GNDAU1 5.0 ± 0.1 PCB side A PGND3 GNDAU1 AVCC5 Fig. 8.2: Spots to check in VD8, AVCC5 voltages AVH-P6300BT/XNUC...
Page 50
Rated value 3 1 DACCK 2.0 V~VCC33V DGND~0.8 V 36.8640 MHz ± 300 ppm 2 DACCK 2.0 V~VCC33V DGND~0.8 V 33.8688 MHz ± 300 ppm Rated value 1 Rated Rated value 2 value 3 Fig. 9.2: Rated value of a clock AVH-P6300BT/XNUC...
Page 51
PCB side A Spot to check 2 (IC1501 148pin) Spot to check 1 (probe) Fig. 9.3: Spots to check in 27 MHz, DACCLK AVH-P6300BT/XNUC...
Page 52
VCC33V-0.6V or more 0.4V or less Waveform 1 2 SRCK VCC33V-0.6V or more 0.4V or less Waveform 2 3 LRCK VCC33V-0.6V or more 0.4V or less Waveform 3 Rated value 2 Rated value 1 Fig. 10.2: Rated value of serial three wires AVH-P6300BT/XNUC...
Page 53
Spot to check 1 (sending pin) Rated value (rms) Reference waveform 4 LO 1400 ± 150 mV Waveform 4 5 RO 1400 ± 150 mV Waveform 4 Rated value is an effective value (rms) Fig. 10.4: Rated value of analog audio out (LO, RO) AVH-P6300BT/XNUC...
Page 54
Checking should be performed after connecting 24Pin FFC to the jig or other equipment. Spot to check 1 (sending pin) Rated value 1 Rated value 2 Reference waveform 6 IEC VCC33V-0.6V or more 0.4V or less Waveform 5 PCB side A Fig. 10.6: Spot to check in digital audio signal (IECOUT) AVH-P6300BT/XNUC...
Page 55
PEAK COMPOSITE signal Rated value Color burst Pedestal level BOTTOM Horizontal synchronous signal Fig. 11.2: Waveform when 100% composite white is output PCB side A COMPOSITE Fig. 11.5: Spot to check in VIDEO signal AVH-P6300BT/XNUC...
Page 56
(For how to display the LD live time, see FE Test Mode) 2. The second digit of the live time from the left being E as in “*E** ****” means the FLASH memory has reached the end of its life. E.g.: AVH-P6300BT/XNUC...
*4 Available only for the models compatible with DVD-A. In case of an error, the audio output will be muted only but the playback operation will continue. Also, acceptance of the user operation will be the same as normal. AVH-P6300BT/XNUC...
Page 59
Select a file that rate not sup- rate is more than can be played. ported. 30 fps. Audio Format This type of file is Select a file that not sup- not supported on can be played. ported. this unit. AVH-P6300BT/XNUC...
Page 60
9X/-DX failed. cable from the please contact iPod. Once the your dealer or an iPod’s main menu authorized Pioneer is displayed, recon- Service Station. nect the iPod and reset it. Pandora iPod failure. Disconnect the cable from the...
If the angle VOL voltage becomes approximately 90° voltage, the discharge is completed by braking the motor for angle driving. (If the previous angle is memorized, the operation is carried out with the angle) 90° voltage or last memory position AVH-P6300BT/XNUC...
Page 63
After the horizontal operation status detection pulse is detected 15 times, the motor for anteroposterior driving is rotated to the storage direction in low speed. If the horizontal operation status detection pulse cannot be detected for 600 ms, the brake is operated and the monitor storage is completed. AVH-P6300BT/XNUC...
Page 64
However, if the monitor is forcibly moved with hands etc., it is not memorized. 2. If the predefined pulse cannot be detected during the horizontal operation, the operation should be stopped at that point. AVH-P6300BT/XNUC...
Page 72
Middle DVD: Middle Select CD Search destination CRG home position 5 Select CRG Move Select completed Select 5 Select Return CRG transfers to the outermost circumference <In case of an error> Select <In case of an error in Power_OFF> AVH-P6300BT/XNUC...
Page 73
Test mode command NULL * In CRG+/-, operation stops when the key is released. At that time, the DVD mecha should make the key command request (TP = B1h) on a regular basis to prevent any omission of key release. AVH-P6300BT/XNUC...
Page 74
D1 = 03h, set the TE offset coefficient to D2 – D9 and transmit [1 second later] D1 = 07h, set the DBAL coefficient to D2 – D9 and transmit [1 second later] D1 = 01h, after setting the status display data to D2 – D9 and transmitting, wait for keys AVH-P6300BT/XNUC...
Page 75
End displaying RF level value Tracking Close status (3),(4) Measure Switch playback Power Off Focus Jump ID Search T.Jump Tracking Open error ratio speed Note 3 Note 4 (1)-(4) Specify No. Specify ID of tracks Start ID search Start jumping AVH-P6300BT/XNUC...
Page 76
Register set time set time [How to specify a set time] Specify a digit with the commands (1) and (2). Commands (3) and (4) are to increase/decrease the number. Determine with the command (5). Cancel with the command (8). AVH-P6300BT/XNUC...
Choose "Version Check" among the monitor test mode menu screen. [Display specifications] When 8 digits of read number is strange, displayed with red. [Operation specification] Operational description Remote controller key Return to test mode menu Page up Page down AVH-P6300BT/XNUC...
Page 78
In case the EEPROM initialization has been performed. In case the adjustment value has been initialized. Calibration inspection : In case the calibration inspection has never been performed. In case the EEPROM initialization has been performed. In case the adjustment value has been initialized. AVH-P6300BT/XNUC...
Page 79
X/Y information of [MIN] and [MAX] of the outermost circumference are displayed. [BEFOR] indicates the value stored in the EEPROM. [AFTER] indicates MIN/MAX of the A/D value currently captured. [Operation specification] Operational description Remote controller key Return to top menu AVH-P6300BT/XNUC...
Page 80
Order of display of the locations to be pressed. This point is intended to end the calibration inspection, and therefore, the corrected value of this point is not obtained. [Operation specification] Operational description Remote controller key Return to top menu AVH-P6300BT/XNUC...
Page 81
: The coordinate (X direction, Y direction) which is the result of adding the correction by calibration to the normalized coordinate is displayed. 16 calibration points "+" are displayed in white. [Operation specification] Operational description Remote controller key Return to top menu AVH-P6300BT/XNUC...
Page 82
The incorrect touch will make the characters of cursor turn red. Repeat this for 4 points, and “OK” is displayed upon the last press of 4th point. [Display specifications] confirming The pushing order [Operation specification] Operational description Remote controller key Return to top menu AVH-P6300BT/XNUC...
Page 83
When the adjusted value has been initialized (Data initialize). When the EEPROM has been initialized. [Operation specification] Operational description Remote controller key Selection cursor up movement Selection cursor down movement Return to test mode menu Menu enter AVH-P6300BT/XNUC...
Page 84
When normally ends, "It succeeded" is displayed. When will not end in four seconds, judged to be abnormal, "It failed" is displayed. [Operation specification] Operational description Remote controller key Selection cursor left movement Selection cursor right movement Return to test mode menu Menu enter AVH-P6300BT/XNUC...
Page 85
[MONOCHROME STRIPE] Display of monochrome stripe signal (1dot Width) [Operation specification] Operational description Remote controller key Return to test mode menu [COLOR BAR] Display of color bar signal [Operation specification] Operational description Remote controller key Return to test mode menu AVH-P6300BT/XNUC...
Page 86
Display of Black/White signal [Operation specification] Operational description Remote controller key Return to test mode menu Next signal [CENTER MARKER] Display of signal for screen central location setting. [Operation specification] Operational description Remote controller key Return to test mode menu AVH-P6300BT/XNUC...
Slide the Grille Assy forward by pushing two tabs with tweezers or other item. Attach and remove the Grille Assy by sliding it horizontally. How to assemble the Grille Assy As the mother PCB SD part is fixed with the Grille Assy, insert it horizontally. Fig.1 AVH-P6300BT/XNUC...
Page 88
How to separate the Drive Unit and the (Rear Side) Chassis Assy (Fig. 2) Remove the seven screws and then sepa- rate the Drive Unit and the Chassis Assy. (Left Side) Drive Unit Chassis Assy (Right Side) Fig.2 AVH-P6300BT/XNUC...
Page 89
Remove the four screws and then lift the Bracket toward the Drive Unit. Drive Unit DVD Mechanism Module Remove the four screws. Disconnect the connector and then remove the DVD Mechanism Module. Drive Unit Disconnect the two connectors and then remove the Drive Unit. Fig.3 AVH-P6300BT/XNUC...
Page 90
Holder. Holder Fig.4 Removing the DVD Amp Unit (Fig.5) Remove the three screws. Disconnect the connector. (Only BT model) Straighten the tabs at three locations indi- cated and then remove the DVD Amp Unit. DVD Amp Unit Fig.5 AVH-P6300BT/XNUC...
Page 91
Removing the Motor Unit, the Drive Unit can operate to lead to the Monitor Assy. Motor Unit Remove the two screws and then remove the two Guids(Right side, Left side). Pull out the Monitor Assy in the direction indicated by an arrow. Fig.6 AVH-P6300BT/XNUC...
Page 92
Disconnect the connector. Case Unit Cover Keyboard PCB Disconnect the three connectors. Straighten the tabs at two locations indi- cated and then remove the Monitor PCB. Remove the screw. Disconnect the connector and then remove the Keyboard PCB. Monitor PCB Fig.7 AVH-P6300BT/XNUC...
Page 93
Removing the Holder of LCD (Fig.8) Holder Insert the tweezers (thin one) as shown in the figure and remove the tab. Caution If you pick up the tab forcibly, the plate bends. It can be removed by just inserting the tweezers straightly. Fig.8 AVH-P6300BT/XNUC...
Page 94
Removing the BT PCB and the BT ANT PCB (Fig.9) Straighten the tabs at two locations indicated and then remove the BT PCB. Disconnect the Cord Assy using GGF1539. Remove the screw and then remove the BT ANT PCB. BT PCB BT ANT PCB Fig.9 AVH-P6300BT/XNUC...
Page 95
The sticking direction is shown on the right figure. When you install the grille to the PCB, confirm the cushion is sticking on the Panel PCB properly. Attention: How to install the Sheet (AVH-P6300BT/XNUC) Pasting position is shown below. Align plate to bending line and square hole.
Page 96
5. Take care not to catch the flexible part on the side face. 6. Take note that a deformation may be generated if you hold the front part of the upper frame or CRG mechanism part or a foreign object is inserted. Handling OK AVH-P6300BT/XNUC...
Page 97
Handling NG Fig. 1 Do not touch here Do not touch here Do not touch here : Do not touch here AVH-P6300BT/XNUC...
Page 98
(The flexible part is damaged if the board is removed without removing the flexible part, so be sure to remove it.) Fig. 1 Short circuit Connector (pickup flexible part) Fig. 2 1. Unscrew two screws and remove the CRG motor ASS'Y. CRG motor ASS’Y Locking screw (CRG) Locking screw (CRG) Fig. 3 AVH-P6300BT/XNUC...
Page 99
Be sure to carry out the actual applying of main shaft holddown spring. Retainer plate spring Main shaft PU unit Main shaft holddown spring Fig. 4 Sub shaft Temporary applying part of CRG chassis Temporary applying Actual applying AVH-P6300BT/XNUC...
Page 100
1. When you hold PU, hold “Handling OK” part shown in the figure and do not hold “Handling NG” part. Handling OK Handling NG Do not touch the radiator. Do not touch the ACT(object lens). Do not pull the FPC. Do not touch the Miller or Collimator lens. Fig. 5 AVH-P6300BT/XNUC...
• Once the EJECT key is pressed, do not press any other key until the disc is completely ejected. • Power OFF immediately in case of run a way. • Turning the volume for adjusting the laser power of the pickup unit may result in the breakage of the laser diode. AVH-P6300BT/XNUC...
Page 102
(method 1) and adjustment while checking the RF level values with the OSD (method 2). The adjustment procedure is shown below. For how to enter the test mode and the operation procedure, see the sections in the Service Test Mode. AVH-P6300BT/XNUC...
Page 103
(Perform adjustment in order of A => B => A, and finally rotate the screws clockwise to complete adjustment.) 11. Power OFF in the test mode, and check that the disc is stopped before ejecting. 12. Apply adhesive for fixing skew and screw lock. See the figure below for the spots to adhere. AVH-P6300BT/XNUC...
Page 104
D & E Sectional diagram of the spot to adhere in R-SKEW * Note: Make sure to cross-link both the resin and sheet-metal parts. Spots to apply adhesive * Note: Make sure to cross-link both the case and sheet-metal parts. AVH-P6300BT/XNUC...
Page 105
Precautions in handling pickup * Note: Avoid contact with the shaded part shown in the figure below. RF level adjustment part Avoid contact with optical components. Avoid contact with the spring. Hologram (beware of static electricity) GRT adjustment part AVH-P6300BT/XNUC...
Screw adjacent to mark on the product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions,apply as you think it appropriate.) 9.1 PACKING BT/UC AVH-P6300BT/XNUC...
Page 111
See Contrast table (2) Contain Box See Contrast table (2) 18-4 Warranty Card See Contrast table (2) Protector CHP2540 (2) CONTRAST TABLE AVH-P6300BT/XNUC, AVH-P6350BT/XNRD and AVH-P6350BT/XNRI are constructed the same except for the fol- lowing: Mark Description AVH-P6300BT/XNUC AVH-P6350BT/XNRD AVH-P6350BT/XNRI Screw Assy...
Page 113
Grille See Contrast table (2) Remote Control Unit CXE3877 CDE9140 Battery Cover CNU1624 Cover CNN3221 (2) CONTRAST TABLE AVH-P6300BT/XNUC, AVH-P6350BT/XNRD and AVH-P6350BT/XNRI are constructed the same except for the fol- lowing: Mark Description AVH-P6300BT/XNUC AVH-P6350BT/XNRD AVH-P6350BT/XNRI Grille Assy CXE4183 CXE4184...
Page 115
Cover CNU1130 Grille Assy See Contrast table (2) Screw BPZ20P060FTC DVD Mechanism Module(MS7) CXK6900 CDE9146 (2) CONTRAST TABLE AVH-P6300BT/XNUC, AVH-P6350BT/XNRD and AVH-P6350BT/XNRI are constructed the same except for the fol- lowing: Mark Description AVH-P6300BT/XNUC AVH-P6350BT/XNRD AVH-P6350BT/XNRI Monitor Unit(Service) CXX3040 CXX3041...
Page 117
See Contrast table (2) CNV6727 EMI Absorb Sheet See Contrast table (2) DVD Amp Unit(Service) See Contrast table (2) (2) CONTRAST TABLE AVH-P6300BT/XNUC, AVH-P6350BT/XNRD and AVH-P6350BT/XNRI are constructed the same except for the fol- lowing: Mark Description AVH-P6300BT/XNUC AVH-P6350BT/XNRD AVH-P6350BT/XNRI...
Page 125
No differentiation is made between chip resistors and DVD AMP UNIT (SERVICE) discrete resistors. Consists of Symbol indicates a capacitor. MOTHER PCB CHIP SIZE LEGEND No differentiation is made between chip capacitors and 1608 TUNER PCB 2125 discrete capacitors. 3216 NM : No Mount AVH-P6300BT/XNUC...
Page 133
8 EN1 270p/50 VREG 9 EN2 R1513 SGND R1506 10 CT 11 TL_CTRL 12 FLAG SYNC R1507 R1516 AN33012UA GNDDDC DVD AMP UNIT (SERVICE) Consists of MOTHER PCB : The power supply is shown with the marked box. TUNER PCB AVH-P6300BT/XNUC...
10.11 MAIN PCB UNIT, SWITCH PCB UNIT and VOLUME PCB UNIT MAIN PCB UNIT CN2001 AVH-P6300BT/XNUC...
Page 161
M102 CXC6638 CSN1081 SWITCH PCB UNIT M103 CXC6639 VOLUME PCB UNIT Decimal points for resistor and capacitor fixed values are expressed as : 0.022 R022 AVH-P6300BT/XNUC...
11.7 MAIN PCB UNIT, SWITCH PCB UNIT and VOLUME PCB UNIT MAIN PCB UNIT SIDE A Angle sense VOLUME PCB UNIT CN2001 ANGLE MOTOR Angle sw CN102 SWITCH PCB UNIT SLIDE MOTOR MAIN PCB UNIT SIDE B VOLUME PCB UNIT CN103 AVH-P6300BT/XNUC...
Example) IC 301 is on the point (face A, 91 of x-axis, and 111 of y-axis) of the corresponding PC board. IC 301 (A, 91, 111) IC NJM2068V Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. DVD Amp Unit(Service) A:AVH-P6300BT/XNUC Consists of B:AVH-P6350BT/XNRD Mother PCB Tuner PCB C:AVH-P6350BT/XNRI Unit Number : CXX3036(A) : CXX3037(B)
Page 195
CTF1778 D 126 (A,144,120) Diode RKZ5.6KG(B2) L 803 (A,72,93) Chip Ferrite Bead DTL1107 D 127 (B,148,132) Diode RKZ20KG(B2) D 151 (B,132,142) Diode CRG03 L 901 (B,66,65) Inductor CTF1786 D 152 (B,135,142) Diode CRG03 L 921 (B,93,86) Ferrite Bead CTF1528 AVH-P6300BT/XNUC...
Page 196
(A,15,123) Connector CKS5543 R 262 (B,56,127) RS1/16SS471J CN2021 (A,36,133) Connector CKS5732 JA301 (A,15,162) Connector CKS3414 R 263 (B,56,129) RS1/16SS471J JA481 (A,43,163) Jack(B,C) CKN1050 R 264 (B,56,130) RS1/16SS471J R 265 (B,76,134) RS1/16SS471J RESISTORS R 266 (B,76,133) RS1/16SS471J R 267 (A,62,142) RS1/16SS0R0J AVH-P6300BT/XNUC...
Page 197
R 444 (B,97,139) RS1/16SS390J R 626 (A,138,109) RS1/16SS471J R 445 (B,97,132) RS1/16SS390J R 627 (B,139,83) RS1/16SS473J R 446 (B,97,129) RS1/16SS390J R 628 (B,140,80) RS1/16SS473J R 447 (B,97,136) RS1/16SS223J R 629 (B,140,83) RS1/16SS473J R 448 (B,97,135) RS1/16SS223J R 630 (B,141,83) RS1/16SS473J AVH-P6300BT/XNUC...
Page 198
(A,53,84) RS1/16SS221J R 853 (A,74,59) RS1/16SS220J R 760 (A,53,90) RS1/16SS0R0J R 855 (A,70,62) RS1/16SS220J R 761 (A,53,96) (B,C) RS1/16SS101J R 856 (A,72,60) RS1/16SS391J R 762 (B,50,81) RS1/16SS472J R 857 (A,84,95) RS1/16SS0R0J R 763 (B,50,82) RS1/16SS472J R 866 (A,100,56) RS1/16SS103J AVH-P6300BT/XNUC...
Page 199
R 987 (B,42,125) RS1/16SS105J R 1743 (A,103,164) RS1/16SS221J R 988 (B,39,125) RS1/16SS105J R 1744 (A,100,164) RS1/16SS473J R 990 (B,41,118) RS1/16SS103J R 1745 (A,100,162) RS1/16SS103J R 991 (B,39,118) RS1/16SS103J R 2001 (B,18,121) RS1/16SS102J R 992 (B,40,118) RS1/16SS103J R 2002 (B,16,121) RS1/16SS102J AVH-P6300BT/XNUC...
Page 200
C 231 (B,127,124) CKSRYB104K16 C 401 (B,90,154) CKSRYB104K50 C 232 (A,120,127) Capacitor CEVLW470M16 C 402 (B,77,149) 4.7 uF CCG1201 C 233 (B,127,121) 10 uF DCH1165 C 403 (B,77,152) 4.7 uF CCG1201 C 234 (B,122,112) CCSQCH223J50 C 404 (B,90,151) CKSRYB104K50 AVH-P6300BT/XNUC...
Page 201
(A,86,95) CKSRYB105K10 C 984 (B,38,125) CKSSYB102K50 C 816 (A,80,64) CKSSYB104K10 C 985 (B,43,117) CKSSYB104K10 C 817 (B,82,90) CKSSYB104K10 C 1001 (A,160,132) Capacitor CEVLW470M6R3 C 818 (A,88,97) CKSSYB104K10 C 1002 (B,157,133) CKSSYB103K16 C 819 (A,90,94) CKSSYB104K10 C 1003 (B,155,133) CKSRYB103K50 AVH-P6300BT/XNUC...
Page 202
C 1449 (B,44,24) CKSSYB103K16 C 2021 (B,45,136) CKSSYB102K50 C 1450 (B,33,23) CKSSYB103K16 C 2022 (B,45,135) CKSSYB102K50 C 1451 (B,33,22) CKSSYB103K16 C 1453 (B,39,17) CCSSCH100D50 C 1454 (B,36,7) CKSSYB104K10 Unit Number : YWX5010 C 1455 (B,38,4) CKSRYB104K16 C 1457 (B,35,5) CCSSCH100D50 AVH-P6300BT/XNUC...
Page 203
R 1212 (A,20,12) RS1/16SS102J R 1536 (A,72,39) RS1/16SS104J R 1213 (B,23,21) RS1/10SR1R0J R 1537 (A,73,41) RS1/16SS104J R 1214 (B,22,20) RS1/10SR1R0J R 1538 (A,64,7) RS1/16SS104J R 1215 (B,24,21) RS1/10SR1R0J R 1539 (A,79,32) RS1/16SS101J R 1216 (B,27,21) RS1/10SR1R0J R 1540 (A,73,40) RS1/16SS221J AVH-P6300BT/XNUC...
Page 204
C 1207 (A,33,20) CKSRYB104K16 C 1610 (A,55,38) CKSSYB104K10 C 1208 (A,33,15) CKSSYB104K16 C 1611 (A,55,36) CKSSYB104K10 C 1212 (A,32,25) CKSSYB104K16 C 1612 (A,55,40) CKSSYB104K10 C 1213 (B,22,26) CKSSYB222K50 C 1613 (A,56,40) CKSSYB104K10 C 1214 (B,22,28) CKSRYB104K16 C 1614 (A,57,40) CKSSYB104K10 AVH-P6300BT/XNUC...
Page 205
R 3022 (B,67,6) RS1/16SS103J R 3023 (B,66,6) RS1/16SS151J R 3024 (B,65,6) RS1/16SS151J Keyboard Unit Consists of R 3025 (B,64,6) RS1/16SS0R0J R 3027 (B,39,12) RS1/16SS103J Panel PCB R 3028 (B,36,9) RS1/16SS151J Keyboard PCB R 3029 (B,37,9) RS1/16SS101J R 3030 (B,39,9) RS1/16SS0R0J AVH-P6300BT/XNUC...
Page 206
(A,128,61) IC S-1172B34-E6 R 107 RS1/16S102J IC 5301 (A,95,34) IC NJM2505AF R 108 RS1/16S102J IC 5311 (A,97,43) IC TC75S57FU R 109 RS1/16S102J IC 5312 (A,89,43) L-MOS And Gate TC7SET08FUS1 R 110 RS1/16S102J IC 5401 (A,22,67) Flash ROM Unit(A) PEH302B8 AVH-P6300BT/XNUC...
Page 207
R 5522 (A,81,63) RS1/16SS271J X 5502 (A,71,75) Oscillator 9.597 MHz CSS1787 CN5002 (A,117,34) Connector CKS6008 R 5523 (A,87,59) RS1/16SS271J CN5101 (A,121,14) Connector CKS5561 R 5524 (A,37,48) RAB4CQ103J CN5601 (A,102,74) Connector CKS6062 R 5530 (A,90,60) RS1/16SS101J CN5701 (A,17,16) Connector CKS5561 AVH-P6300BT/XNUC...
Page 208
CKSSYB104K10 R 5804 (A,109,54) RS1/16SS103J C 5304 (A,89,32) CKSSYB104K10 R 5811 (A,113,53) RS1/16SS391J C 5305 (A,91,35) 10 uF DCH1201 R 5812 (A,115,53) RS1/16SS391J C 5307 (A,89,41) CKSSYB104K10 R 5813 (A,116,54) RS1/16SS0R0J C 5308 (A,97,41) CKSSYB104K10 R 5814 (A,114,54) RS1/16SS103J AVH-P6300BT/XNUC...
Page 209
C 5550 (A,42,67) CKSRYB105K10 C 5551 (A,48,71) CKSSYB104K10 C 5552 (A,50,75) CKSSYB104K10 C 5553 (A,52,73) CKSSYB104K10 C 5554 (A,70,46) CKSSYB104K10 C 5555 (A,36,56) CSZSR470M10 C 5556 (A,69,72) CCSSCH180J50 C 5557 (A,40,73) CSZSR470M10 C 5558 (A,71,77) CCSSCH180J50 C 5560 (A,64,76) CKSSYB104K10 AVH-P6300BT/XNUC...
Need help?
Do you have a question about the AVH-P6300BT/XNUC and is the answer not in the manual?
Questions and answers