Electrical Connection; Warning! This Appliance Must Be Earthed - Hoshizaki KM-150BAF-E Installation Manual

3. The location should provide a firm and level
foundation for the equipment.
4. Allow 15 cm. clearance at rear, sides and top
for proper air circulation and ease of
maintenance and/or service should they be
required.
5. This appliance is not suitable for installation
in an area where a water jet could be used
and where dripping is not allowed.
6. Do not place anything in front of the Louver.
7. This icemaker will not work at subfreezing
temperatures. To prevent damage to the
water supply line, drain the icemaker when
air temperature is below zero.
4. INSTALLATION 4. INSTALLATION 4. INSTALLATION 4. INSTALLATION 4. INSTALLATION
• The installation must be carried out by qualified per-
sonnel, in accordance with current regulations,
according to the manufacturer's instruction.
• Incorrect installation can cause harm to people, ani-
mals the icemaker, or the installation location, for
which the manufacturer cannot be held responsible.
1) Unpack the icemaker, and attach the four adjustable
legs provided (optional) to the bottom of the Storage
Bin by lifting the front of the icemaker and then lifting
the back of the icemaker (DO NOT TURN THE
ICEMAKER UPSIDE-DOWN).
2) Position the icemaker in the selected permanent
position.
3) Level the icemaker in both the left-to-right and front-
to-rear directions by turning the Bin Leg Adjusters
with a wrench.
4) Replace the panels in their correct positions.

5. ELECTRICAL CONNECTION

5. ELECTRICAL CONNECTION
5. ELECTRICAL CONNECTION 5. ELECTRICAL CONNECTION 5. ELECTRICAL CONNECTION
THIS APPLIANCE MUST BE EARTHED THIS APPLIANCE MUST BE EARTHED THIS APPLIANCE MUST BE EARTHED THIS APPLIANCE MUST BE EARTHED THIS APPLIANCE MUST BE EARTHED
This icemaker requires an earth that meets the
national and local electrical code requirements. To
prevent possible severe electrical shock to individu-
als or extensive damage to equipment, install a
proper earth wire to the icemaker. Turn off the power
supply before any maintenance, repairs or cleaning
is undertaken.
91U1TB10A9907
WARNING WARNING WARNING
WARNING WARNING
• This icemaker must have a separate power supply or
receptacle of proper capacity. See the Nameplate. It
is recommended that this icemaker be the only
electrical device on its power supply circuit.
• Usually an electrical permit and services of a licensed
electrician are required.
• Factory fitted power cords are coloured in accordance
with the following code:
Green & Yellow = Earth
Blue = Neutral
Brown = Live
• Should the socket outlets in the installation site not be
suitable for the plug supplied with your product, the
plug must be removed (cut off if it is a moulded on
plug) and an appropriate plug fitted.
As the colours of the wires in the power cord of this
appliance may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows:
The wire which is coloured Green-and-Yellow must
be connected to the terminal in the plug which is
marked with the letter E or by the symbol
coloured Green or Green-and-Yellow. The wire
which is coloured Blue must be connected to the
terminal which is marked with the letter "N" or coloured
Black. The wire which is coloured Brown must be
connected to the terminal which is marked with the
letter L or coloured Red.
If the non-rewirable plug has been cut from the power
supply cord, it must be disposed of. There should be
no attempt to reuse it. Inserting such a plug into a
socket elsewhere presents a serious risk of electrical
shock.
For the U.K. and the Republic of Ireland only For the U.K. and the Republic of Ireland only
For the U.K. and the Republic of Ireland only For the U.K. and the Republic of Ireland only For the U.K. and the Republic of Ireland only
• The non-rewirable plug must never be used without
a fuse cover being fitted.
• The correct replacement for the detachable fuse cover
is identifiable from the manufacturer's reference
number stamped on the plug.
• Supply of replacement fuse covers can be obtained
from Hoshizaki Parts/Service Centres.
• Fuses should be rated at 13A and approved to BS
1362.
3
ENGLISH
or