Advertisement
PRIOR TO USE
Step One
•
Inspect the equipment before each use. Make sure that the Lap Pad rotates smoothly to the inverted position (approximately 90 degrees) and
back and that all fasteners are secure.
Step Two
•
The DEX II
features two adjustment settings that allow you to properly adjust the equipment for your body type. Make sure the equipment is
TM
properly adjusted every time you use the equipment by doing the following procedures:
A. Adjust the height of the Lap Pad:
i.
Loosen the Height Adjustment Knob by rotating it several turns counterclockwise.
ii. Pull the locking pin for the Chrome Shaft while lifting or lowering the Lap Pad by the Height
Adjustment Handle on the back of the Lap Pad.
iii. Select a height setting so that your hips are at the same height as the top edge of the Lap
Pad.
iv. Release the Locking Pin so that it engages fully into one of the height settings. Tighten the
Height Adjustment Knob by rotating clockwise.
v. Make sure the Locking Pin is fully engaged and the Height Adjustment Knob is tightened
prior to use. Failure to do so could result in serious injury!
B. Adjust the width between the Leg Rollers and Lap Pad:
i.
Loosen the Leg Width Adjustment Knob by rotating it several turns counterclockwise.
ii. Pull out on the Leg Width Adjustment Knob and slide the Leg Rollers in or out depending on
your leg width and comfort.
iii. Release the Leg Width Adjustment Knob so that it engages fully into one of the hole settings.
Tighten the Leg Width Adjustment Knob by rotating clockwise.
iv. Make sure the Leg Width Adjustment Knob is fully engaged and tightened prior to use.
Failure to do so could result in serious injury!
HOW TO INVERT
The DEX II
operates strictly under user control - that is, you are able to rotate the unit as slow or as fast as you desire. You will need to use the
TM
strength of your arms to lower your body down and to return upright. If you are unsure about your ability to operate the equipment properly, always
have a spotter nearby or discontinue the use of the equipment.
Step One
•
Step onto the cross bar of the Base Frame with thighs between the Leg Rollers and Lap Pad.
Step One
•
Determine whether the width between the Leg Rollers and Lap Pad is comfortable. Adjust if
User stands inside
the Leg Rollers - hips
necessary.
should align with the
•
Determine whether the Lap Pad is at the correct height. Your hips should be the same height
top edge of the Lap
Pad
as the top edge of the Lap Pad. Adjust if necessary.
DEX II
User Manual
TM
USER MANUAL
B. Adjust Leg Width
LD-2000
Pg.2
ASSEMBLY
STEP ONE
Assemble the Feet (D1-1012, D1-1013) onto the Base Frame (H1-2009) and the Legs
(H1-2010)
•
Slide the Base Frame Feet (D1-1012) on to the Base Frame. (See Figure 1A)
•
Slide the Leg Feet onto the end of the Legs with the cane handle. (See Figure 1B)
•
Push firmly on all four feet to ensure they are fully mounted.
Figure 2a
A. Adjust Height
STEP THREE
Assemble the Lap Pad (D1-1005) to the Lap Pad Frame (H1-2006)
Unscrew the pre-assembled Lap Pad Screws (H1-2007) from the bottom of
•
the Lap Pad. Keep this hardware nearby.
•
With the Lap Pad face down, rest the Lap Pad Frame on top of the Lap Pad.
Make sure the Traction Handles are pointing up and the Leg Support Shaft
Housing rests inside the indented area of the Lap Pad. Align the holes of the
Lap Pad Frame with the holes in the bottom of the Lap Pad. (See Figure 2b)
Insert the Lap Pad Screws through the holes and tighten with the Screwdriver
•
(H1-2015).
•
Continue with securing the Lap Pad Assembly to the Base Frame Assembly
as outlined in the original assembly instructions.
DEX II
ASSEMBLY INSTRUCTIONS
Leg Housings
STEP TWO
Attach the Legs (H1-2010) to the Base Frame (H1-2009)
•
With the cane handles facing upward, insert the Legs into the Leg
Housings of the Base Frame until the two holes in the Leg Housing
align with the holes at the top of each Leg. (See Figure 2a)
•
Insert a Threaded Bolt (H1-2011) from the inside of the Leg Housing
through the holes on each column. Finish on the outside of the Base
Frame using the Flat Washer (H1-2013), Lock Washer (H1-1301) and
Bolt Cap (H1-2012) and tighten with Wrenches (H1-2014).
TM
Assembly Instructions
Figure 1A
Figure 1B
Traction Handles
Figure 2b
Leg Support
Shaft Housing
LD-2000
Pg 3
Advertisement
