Farmi Forest CH27 ACR Operation, Maintenance And Spare Parts Manual

Farmi Forest CH27 ACR Operation, Maintenance And Spare Parts Manual

Crane feed chipper
Table of Contents

Advertisement

Quick Links

CRANE FEED CHIPPER
CH27 ACR & ACC
OPERATION, MAINTENANCE
AND SPARE PARTS MANUAL
PLEASE READ THE OPERATING AND MAINTENANCE
INSTRUCTIONS BEFORE YOU OPERATE THE MACHINE.
FROM MACHINE: 000141
TRANSLATION OF THE INSTRUCTION MANUAL
C-EN-091219-ER

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CH27 ACR and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Farmi Forest CH27 ACR

  • Page 1 CRANE FEED CHIPPER CH27 ACR & ACC OPERATION, MAINTENANCE AND SPARE PARTS MANUAL PLEASE READ THE OPERATING AND MAINTENANCE INSTRUCTIONS BEFORE YOU OPERATE THE MACHINE. FROM MACHINE: 000141 TRANSLATION OF THE INSTRUCTION MANUAL C-EN-091219-ER...
  • Page 3: Table Of Contents

    STARTING THE CHIPPER EQUIPPED WITH SMART FEED SYSTEM CONTROLLING THE FEED BY SELECTOR SWITCH RADIO CONTROL SMART FEED CONTROL FUNCTION DURING CHIPPING CHIPPING ADJUSTMENT OF THE FEED SPEED STOPPING THE CHIPPER LOCATION AND USE OF SAFETY SWITCHES STORAGE INSTRUCTIONS CH27 ACR & ACC...
  • Page 4 200002230 JOINT FRAME 200001339 FEED CONVEYOR ACC 200002328 3PSL SUPPORT LEGS 200002810 FEED CONVEYOR BC3000 (ACCESSORY) 200002586 OIL COOLER (ACCESSORY) 200002584 HYDRAULIC UNIT HD50 (ACCESSORY) 200002589 EMK27 STATIONARY CHIPPER PLATFORM (ACCESSORY) 200002373 CROSS BREAKER (ACCESSORY) PRODUCT REGISTRATION FORM CH27 ACR & ACC...
  • Page 5 SFS EN ISO 12100, SFS EN ISO 4254-1, SFS EN ISO 13857 The following additional standards and specifications have been applied for the conceptional design of the machine: SFS ISO 730-1, SFS ISO 2332, SFS EN 13525 Iisalmi 9.12.2019 (Place) (date) Ilkka Kuuramaa CH27 ACR & ACC...
  • Page 6: Introduction

    Complete the registration form on the last pages of this manual and return it to us within 30 days after the receipt of the product. CUSTOMER FEEDBACK We are happy to receive your opinions and suggestions for improvements by mail or e-mail. All implemented suggestions for improvements will be rewarded. CH27 ACR & ACC...
  • Page 7: General Description And Intended Use Of The Chipper

    FARMI CH27 + ACR FARMI CH27 + ACC FARMI CH27 + ACR + BC3000 The FARMI CH27 chipper must never be coupled to other feed units. Mo- reover, the chipper must not be used without a feed unit. ATTENTION CH27 ACR & ACC...
  • Page 8: Machine Combinations For Grab Loader Feed

    EXCLUSIVELY FOR GRAB LOADER FEED! MANUAL FEED PROHIBITED! WARNING CH27 + ACR CH27 + ACR CH27 + ACC CH27 + BC3000 CH27 + ACC + HK4066 / 4571 / 4581 / CR40 / CR46 CH27 + ACR + BC3000 CH27 ACR & ACC...
  • Page 9: Accessories

    • Recommended for use in contracting work. HD 50 Oil cooler Cross breaker Hydraulic discharge pipe control Radio control 3PSL crane mounting bracket Teleradio Panther and hydraulic support legs CH27 ACR & ACC...
  • Page 10: General Safety Instructions

    • misuse caused by an untrained person’s improper actions. • alterations made without the manufacturer’s permis- sion. Written authorization must be requested from the manufacturer for any alterations to the machine. ATTENTION CH27 ACR & ACC...
  • Page 11 12. All safety and warning signs on and in the machine must be legible and intact. 13. The machine may not be operated by persons who are unwell or under the influence of drugs or alcohol. CH27 ACR & ACC...
  • Page 12 11. Most hydraulic oils do not evaporate easily. Risk factors include hot oil, spills and oil mist (pressurized). 12. If oil gets into your eyes, rinse with plenty of water and contact a doctor. CH27 ACR & ACC...
  • Page 13 Caps, funnels, sieves and filling holes must also be clean. 18. Never store oil outdoors, as water could condense in it. 19. Always dispose of oil in a suitable container, never into the environment! CH27 ACR & ACC...
  • Page 14: General Safety Instructions For The Chipper

    12. Do not remove, lock, disable or modify in any other way the stop lever of the feed unit. 13. The feed hopper or the feed unit must not be mounted at a higher or lower position as this would impede the stop lever function. CH27 ACR & ACC...
  • Page 15: Technical Information

    (Measurement Uncertainty 2,5 dB) Tractor rear window (closed) 97,3 L’ pA, dB(A) 95,8 L’ pA, dB(A) Tractor rear window (open) 106,6 L’ pA, dB(A) 107,0 L’ pA, dB(A) SYMBOLS USED IN THE INSTRUCTIONS WRENCH SPAN WIDTH TORQUE Nm CH27 ACR & ACC...
  • Page 16: Main Components

    13. FEEDING CHUTE ACR / CONVEYOR FEED ACC KNIFE DISC 14. SUPPORT FRAME KNIFE 15. PROTECTION SYSTEM VERTICAL ANVIL 16. 3-POINT MOUNTING FRAME HORIZONTAL ANVIL 17. SAFETY STOP TWIG BREAKER DISCHARGE PIPE WATER DRAINING HOLES 10. HOOK FOR UNIVERSAL SAFT 11. WINCH CH27 ACR & ACC...
  • Page 17: Dimensions

    DIMENSIONS CH27ACR / CH27ACC TRANSPORT POSITION: CH27ACC + SL27 + HK4670 CH27 ACR & ACC...
  • Page 18 200001545 DISCHARGE PIPE, SHORT 1268 HEIGHT WITH THE CHIPPER 27: 2,9 m 200001344 DISCHARGE PIPE, SIDE TRANSITION 2030 LIFTING POINT 2121 LIFTING POINT HEIGHT WITH THE CHIPPER 27: 2,7 - 3,2 m CH27 ACR & ACC...
  • Page 19 200002275 DISCHARGE PIPE, HIGH 1268 HEIGHT WITH THE CHIPPER 27: 3,9 m CH27 ACR & ACC...
  • Page 20: Stickers And Plates

    STICKERS AND PLATES The following plates and labels must be correctly attached to the chipper. Missing safety plates / labels must be replaced immediately. CH27 ACR & ACC...
  • Page 21 Before maintenance and repair, please turn off the tractor and disconnect the PTO drive shaft. CAUTION! Before detaching the chipper from the tractor, it must be placed on a level surface. 4. Wear personal protective equipment. (40142080). 5. Cutting hazard! (40147010) CH27 ACR & ACC...
  • Page 22 There is a risk of being drawn into the feed unit and into the chipper. With the machine in operation, the danger zone extends over 20 meters. (30146990) CH27 ACR & ACC...
  • Page 23 The feed unit is designed for grab loader feed. Manual loading is strictly prohibited! (41019980) 14. Crushing hazard! Always keep a safe distance to rotating parts. (41015600) 15. FARMI Profi sticker (200001878) 16. Manufacturer (40605214) 17. Operation from the tractor cab. (40147050) CH27 ACR & ACC...
  • Page 24: Lifting The Discharge Pipe With The Winch

    Select the transport routes for lifting so that the load is not transported over people or a location where people might be. WINCH HOOK ANCHOR POINT LIFTING POINTS LOCKING THE DISCHARGE PIPE PALLET FORKS CH27ACR / CH27ACC CH27 ACR & ACC...
  • Page 25: Mounting Of The Discharge Pipe

    Insert the M20x260 pin (D), set the discharge pipe to the up- per position and secure it using the wing nut. Fig. 1. CH27 ACR & ACC...
  • Page 26: Adjusting The Discharge Pipe And Lid

    WARNING Always keep a safe distance to the discharge position of the chips. Tighten the lock bands carefully. CH27 ACR & ACC...
  • Page 27: Coupling The 3-Point Mounting To The Chipper

    COUPLING THE 3-POINT MOUNTING TO THE CHIPPER Couple the 3-point mounting to the chipper as shown in the figure, using bolt A (6 pcs), washer B (12 pcs) and lock nut C (6 pcs). CH27 ACR & ACC...
  • Page 28: Mounting The Feed Chute To The Feeder Device (Acr And Acc)

    Mount the feed chute (ACC or ACR) from both sides to the feeder device using bolt A (4 pcs), washer C (4 pcs) and lock nut B (4 pcs). Mount the side walls (ACC and ACR) from both sides to the feeder device using bolt A (8 pcs), washer C (8 pcs) and lock nut B (8 pcs). CH27 ACR & ACC...
  • Page 29: Coupling The Feeder Device To The Chipper (Acr And Acc)

    Mount the feeder device to the chipper with bolt A (1 pc) and B (1 pc), washer C (4 pcs) and lock nut D (2 pcs). The feeder device lugs E fit between the chipper lugs. CH27 ACR & ACC...
  • Page 30: Mounting The Support Frame To The Feeder Device (Acr And Acc)

    MOUNTING THE SUPPORT FRAME TO THE CHIPPER (ACR AND ACC) Mount the support frame to the chipper as shown in the figure, using bolt A (8 pcs), washer B (16 pcs) and lock nut C (8 pcs). CH27 ACR & ACC...
  • Page 31: Bc3000 -> Ch27

    BC3000 -> CH27 CH27 ACR & ACC...
  • Page 32 BC3000 -> CH27 CH27 ACR & ACC...
  • Page 33 Connect the CH27 upper motor’s tank line hydraulic hose to BC3000 motor’s pressure line hydraulic hose with a double fitting. Hose no. 56526270, connector no. 52432051. Connect BC3000 motor’s tank line to CH27 lower motor’s tank line. Hose no. 56526270. BC3000 CH27 CH27 ACR & ACC...
  • Page 35: Shortening The Pto Shaft

    Ensure that the shaft was shortened sufficiently. Check that the shaft has a 20-40 mm clearance. In addition, move the machine sideways and ensure that the PTO shaft does not bottom. Shortening the PTO shaft CH27 ACR & ACC...
  • Page 36: Coupling The Chipper To The Tractor

    The arrows on the hoses show the oil flow direction. Couple the chipper to the tractor in the following order. Link arms Universal shaft Top link Hydraulic hoses Wire harness PALUU / TANK PAINE / PRESSURE CH27 ACR & ACC...
  • Page 37 CONNECTING THE HYDRAULICS ACR CH27 ACR & ACC...
  • Page 38 CONNECTING THE HYDRAULICS ACC CH27 ACR & ACC...
  • Page 39 K1/4"S L=1,05 m 200002526 Hose assembly K1/4S, L=0,35 m + quick coupling, 1/4" 56518710 Hose assembly K1/4”S L=0,25 m 56525066 Hose assembly V1/2”S L=0,55 m NOTE! HD50 hydraulic unit hoses are on the spare parts page. CH27 ACR & ACC...
  • Page 40 CONNECTING THE HYDRAULICS BC3000 (accessory) CH27 ACR & ACC...
  • Page 41 Order no Description Remarks 56526270 Hose assembly K1/2"S L=2,2 m 52390200 Usit seal ring 21,54x28,58x2,49, R 1/2" 56516438 Hose assembly S1/4"S L=4,6 m 52432051 Double fitting R1/2 52432226 Double fitting R1/4-1/2 52449022 Quick coupling male R1/2, SK CH27 ACR & ACC...
  • Page 42: Installing Hd 50 Hydraulic Unit

    INSTALLING HD 50 HYDRAULIC UNIT 1. Remove the tow triangle. 2. Remove the universal shaft shield A and shield brackets B and C. CH27 ACR & ACC...
  • Page 43 3. Mount the large pulley in the threads of the splined shaft with holes pointing outward. 4. Lift the HD unit between the legs of the chipper so that the bolt holes are aligned. CH27 ACR & ACC...
  • Page 44 5. Mount the belt on the pulleys and align the pulleys using a level rod or ruler. Once this is done, tighten the securing bolts and nuts. Lastly, tighten the belts using the J-shaped bolts and nuts on the side of the HD unit. CH27 ACR & ACC...
  • Page 45: Coupling Hd 50 Unit Hydraulic Hoses Without Oil Cooler

    6. Disconnect the pressure hoses and return hoses from the tractor hydraulics. Couple the hydraulic unit hoses as shown in the Figure. 56534175 3/4”, 190, K3/4”S, L=1.2 m 56533052 V3/4”S L=0.5 m 54921382 suction hose, 1 1/4”, 5 bar 56526130 K1/2”S L=0.9 m CH27 ACR & ACC...
  • Page 46: Mounting The Oil Cooler

    MOUNTING THE OIL COOLER 7. Fasten the oil cooler to the hydraulic unit as shown in the Figure. CH27 ACR & ACC...
  • Page 47: Coupling The Hydraulic Hoses Of Hd 50 Unit And Oil Cooler

    8. Couple the hydraulic hoses as shown in the Figure. Finally, reinstall the tow triangle. 56534084 K3/4”S L=0.65 m 56534134 K3/4”S L=0.9 m 56533052 V3/4”S L=0.5 m 54921382 suction hose, 1 1/4”, 5 bar 56526130 K1/2”S L=0.9 m CH27 ACR & ACC...
  • Page 48: Connecting The Oil Cooler To Tractor Battery

    CONNECTING THE OIL COOLER TO TRACTOR BATTERY BATTERY +12VDC FUSE Connect the oil cooler cables to the tractor battery as shown in the Figure. CH27 ACR & ACC...
  • Page 49: Installation Of The Emk27 Electric Motor Mount (Accessory)

    Universal shaft Mount the chipper frame to concrete using M20 or larger Drill 4 holes in the chipper feet concrete anchors. for M24 x 70 screws. 4 pcs M16 x 50 hex screws in the chipper feet CH27 ACR & ACC...
  • Page 50 2. Align the belt pulleys. Tighten the belts. Then, replace the belt guard. 1. Mount the SPB5 x 250 belt pulley to the motor and then mount the motor to the frame. 3. Connect the power supply. CH27 ACR & ACC...
  • Page 51 EXPANSION JOINT 10 mm THICK FULL-ROUND BASE SLAB EXISTING SLAB (THICKNESS UNKNOWN) REINFORCEMENT TOP & BOTTOM - SL81 40 mm COVER ON ALL SIDES - SL82 60 mm COVER AT LEAST M20 CONCRETE ANCHORS CONCRETE N32 EXISTING SLAB (THICKNESS UNKNOWN) CH27 ACR & ACC...
  • Page 52: Operating Instructions

    12. Direct the discharge pipe so that the thrown out chips do not pose a risk to the operator of the chipper or to or anyone else. Always keep a safe distance to the discharge position of the chips. CH27 ACR & ACC...
  • Page 53: Stress Revolution Control Device

    As soon as the cutting disk speed has regained the preset value, the feed rollers continue to feed the wood. The feed speed is thus adapted to the cutting disk speed. Consistent chips are achieved and the operator can focus on material loading. No Stress sensor CH27 ACR & ACC...
  • Page 54: Smart Feed Basic Operating Instructions

    Smart Feed –system works completely automa- tically, without users need to adjust the control system settings. Components of Smart Feed system 200003767 SMART FEED BASIC CH27 ACR, CH27 ACC CABIN CHIPPER CH27 ACR & ACC...
  • Page 55: Starting The Chipper Equipped With Smart Feed System

    When continuous forward feed is on you can use re- verse feeding by turning the selector switch coun- ter-clockwise briefly. Continuous forward feed will switch off if you turn the selector switch counter- clockwise more than two seconds. CH27 ACR & ACC...
  • Page 56: Radio Control

    Then you need to use hydraulic crane to loose the wood. When the blockage is removed, activate forward feed and continue chipping. RADIO CONTROL Feed Feed backward ON / OFF forward (Reverse) CH27 ACR & ACC...
  • Page 57: Chipping

    Re- gularly, check the temperature of the bearings. Pay special attention to careful maintenance, and keep the chipper free from dust. If the chipper starts smoking, pour water into the feed hopper. CH27 ACR & ACC...
  • Page 58: Adjustment Of The Feed Speed

    • The feed speed is correctly adjusted when the mate- rial does not butt against the cutting disk or when the tips of the feed roller do not slow down the material feed. CH27 ACR & ACC...
  • Page 59: Stopping The Chipper

    Please wait until the disk has stop- ped completely before performing any further actions. The chipper requires approx. 9 minutes to slow down from maximum speed to complete stop (1000 rpm -> 0 rpm). FIXED SAFETY SWITCH CH27 ACR & ACC...
  • Page 60: Storage Instructions

    Take appropriate measures to keep the water drainage holes on the lower chamber open. AFTER STORAGE AND BEFORE USE Ensure that the feeder device is empty. Ensure that there is a sufficient amount of oil in the hydraulic unit. CH27 ACR & ACC...
  • Page 61: Maintenance Items

    Lubricate electrical con- 250 h Spray anti-oxidant onto the con- nectors nectors. Feed unit Inspecting the feed chain 50 h If necessary, tighten according to tension instructions. Check the sliding 50 h plates for damage. CH27 ACR & ACC...
  • Page 62: Lubricating The Bearings

    Lubricate the shield tubes in wintertime to prevent them from freezing and sticking. Swing the joints sideways for lubrication. Lubricate the shield tubes in Lubricate the outer profile tube’s inner surface. wintertime to prevent them from freezing and sticking. h = working hours CH27 ACR & ACC...
  • Page 63: Periodic Inspections

    (8 pcs, 4 pcs on each side of the chipper) Tightening the lower nuts on the twig and cross breaker Tightening the upper nuts on the twig and cross breaker Bearing housing fastening screw tension Bearing housing cover fastening screw tension Knife fastening nut tension CH27 ACR & ACC...
  • Page 64: Knife Maintenance

    Remove knife bolts E (4 pcs), nuts F (4 pcs) and lock washers G (4 pcs). Remove knife H. Sharpen or replace the knife. Mount the knife with bolts, lock washers and nuts. Sharpen knives in pairs to keep lengths the same and maintain disk balance. CH27 ACR & ACC...
  • Page 65: Sharpening Cutting Knives

    More thorough conditioning is carried out with a surface grinder, with the knives removed. Burrs are removed from the knife fastening bolt side, grinding with the surface. Fastening bolt side Final grinding of the knife CH27 ACR & ACC...
  • Page 66: Adjusting Chip Length

    5-25 mm. If you would like a longer chip length, move the knife holder farther away from the feed chute. 3. Loosen the nuts for knife holder B. CH27 ACR & ACC...
  • Page 67: Adjusting The Anvils

    Adjust the second knife to the same distance from the edge of the base frame as the first knife. Use the distances measured above as a guide. Adjust the anvils. 1. Loosen the vertical anvil adjusting nuts D. Loosen the vertical anvil screws C. CH27 ACR & ACC...
  • Page 68 Then, adjust the knife using the adjusting nuts D. The cle- arance must be 1-1.5 mm. The horizontal anvil will move along with the vertical anvil. 4. Tighten the knife adjustment nuts D and horizontal anvil screws E. CH27 ACR & ACC...
  • Page 69: Replacing The Slide Plate (Acc)

    REPLACING THE SLIDE PLATE (ACC) Replace the sliding plate in the order of the numbers shown. CH27 ACR & ACC...
  • Page 70: Replacing The Splined Shaft

    Take all electrical/electronic parts to an electrical waste (E-waste) recycling point. Area to be heated Grind a 15-mm-deep groove about 2 mm from the end of the shaft. 72 + 0,5 Replacing the splined shaft CH27 ACR & ACC...
  • Page 71: Troubleshooting

    Feeder device not working. • Check the direction of flow. • Check motor pressure (measuring points in valves MP1 and MP2). • Ensure that the dump valve is activated when using feed forward (FF) or reverse (RR). CH27 ACR & ACC...
  • Page 72 The emergency stop button has been pressed. • While bypassing the No Stress function, the Feed forward switch was activated when the electricity was turned on, but the switch was released before 5 seconds had passed after turning on the electricity. CH27 ACR & ACC...
  • Page 73: Other Indicator Lights

    The light is on continuously. Normal status Continuous feed forward has been activated. Switch can be re- leased. Setting the normal speed of the knife disc The light blinks once every second: The No Stress function has been bypassed. CH27 ACR & ACC...
  • Page 74: 200003767 Smart Feed Basic

    200003767 SMART FEED BASIC CH27 ACR & ACC...
  • Page 75 200004406 Wiring harness, Cabin 2 with control box and selector switch 200004407 Wiring harness, chipper side without sensors 200004408 Pulse sensor No Stress -sensor 200004409 Pressure sensor 200004410 Control module 200004415 Emergency stop push button CH27 ACR & ACC...
  • Page 76: 200004364 Chipper Ch27

    200004364 CHIPPER CH27 CH27 ACR & ACC...
  • Page 77 200004364 CHIPPER CH27 CH27 ACR & ACC...
  • Page 78 Shield for universal shaft 52117108 Lock nut ST8.8ZN, M10, DIN985 200000307 Lock screw ST8.8ZN, M10x35, DIN603 52832045 Drive rivet 4,8X19 43291137 Retainer 116 mm 52842143 Hair pin cotter ZN, 5X105, DIN11024 03291143 Chain 52062031 Hex screw ST8.8ZN, M12X40, DIN933 CH27 ACR & ACC...
  • Page 79 52117940 Thumb screw ST4.6ZN, M10X40, DIN316 52060233 Hex screw ST8.8ZN, M10X30, DIN 933 52062163 Hex screw ST8.8ZN, M16X100, DIN931 200002298 Upfit includes all stickers 200003767 Wiring harness Smart Feed Basic 52110053 Hex nut ST8.8ZN, M12, DIN934 CH27 ACR & ACC...
  • Page 80: 200004365 Knife Disc And 200001292 Bearing System

    200004365 KNIFE DISC AND 200001292 BEARING SYSTEM CH27 ACR & ACC...
  • Page 81 ZN, M12, NORD-LOCK, DIN25201 52117124 Lock nut ST8.8ZN, M12, DIN985 200004019 Bearing unit D60 axle 200001494 Bearing housing 200001497 Tapered roller bearing 200001493 Adapter ring 200001495 Seal 200001496 Cone sleeve 52401015 Grease fitting AR1/8, straight 200001492 End plate CH27 ACR & ACC...
  • Page 82: 200002095 Valve

    200002095 VALVE Part Order no Description Remarks Valve block 200001322 Flow dividing valve 56057243 Directional valve 200001326 Flow control valve feed roller speed 200001327 Flow control valve 200003766 Cartridge valve 200003884 Solenoid coil 200003794 Pressure relief valve CH27 ACR & ACC...
  • Page 83: 200002207 3-Point Mounting, Fastener

    Hose fastener 52200037 Washer ST5.8ZN, M8, DIN126 52060183 Hex screw ST8.8ZN, M8X30, DIN933 52117082 Lock nut ST8.8ZN, M8, DIN985 52062379 Hex screw ST8.8ZN, M24X70, DIN933 52200102 Washer ST5.8ZN, M24, DIN126 52117249 Lock nut ST8.8ZN, M24, DIN985 CH27 ACR & ACC...
  • Page 84: 200001545 Short Discharge Pipe

    200001545 SHORT DISCHARGE PIPE CH27 ACR & ACC...
  • Page 85 ST8.8ZN, M12, DIN934 52200045 Washer ST5.8ZN, M10, DIN125 200001414 Hex screw ST8.8ZN, M10X260, DIN931 52117108 Lock nut ST8.8ZN, M10, DIN985 94612082 Extension spring DU26 DL2,6 L106 58220170 Hex screw ST8.8ZN, M6X50, DIN931 52117066 Lock nut ST8.8ZN, M6, DIN985 CH27 ACR & ACC...
  • Page 86: 200002275 High Discarge Pipe

    200002275 HIGH DISCARGE PIPE CH27 ACR & ACC...
  • Page 87 ST5.8ZN, M10, DIN125 200001414 Hex screw ST8.8ZN, M10X260, DIN931 52117108 Lock nut ST8.8ZN, M10, DIN985 94612082 Extension spring DU26 DL2,6 L106 58220170 Hex screw ST8.8ZN, M6X50, DIN931 52117066 Lock nut ST8.8ZN, M6, DIN985 33295330 Intermediate tube CH27 ACR & ACC...
  • Page 88: 200001344 Discharge Pipe, Side Transition

    200001344 DISCHARGE PIPE, SIDE TRANSITION 3.3 3.2 3.10 3.13 3.12 3.14 3.15 3.11 CH27 ACR & ACC...
  • Page 89 Lock nut ST8.8ZN, M10, DIN985 52063087 Hex screw ST8.8ZN, M20X300, DIN931 54815147 Wire rope lock 43492690 Chain 53804136 Carabiner 10X100, DIN5299C 200001888 Lock screw ST8.8ZN, M12X45, DIN603 43486370 Coupling D20-70 mm 200001414 Hex screw ST8.8ZN, M10X260, DIN931 CH27 ACR & ACC...
  • Page 90: 200002150 Vizor Steering , Manual

    200002150 VIZOR STEERING , MANUAL Part Order no Description Remarks 84614106 Extension spring DU38 DL4,25 L250 54826227 Knot chain 52200037 Washer ST5.8ZN, M8, DIN126 52117082 Lock nut ST8.8ZN, M8, DIN985 CH27 ACR & ACC...
  • Page 91: 200002147 Vizor Steering, Hydraulic

    52117108 Lock nut ST8.8ZN, M10, DIN985 52432101 Double fitting R1/4 52391034 Usit seal ring 13,74X20,57X2,03, R1/4" 52117082 Lock nut ST8.8ZN, M8, DIN985 52200037 Washer ST5.8ZN, M8, DIN126 52060183 Hex screw ST8.8ZN, M8X30, DIN933 43489640 Hose kit CH27 ACR & ACC...
  • Page 92: 200002176 Discharge Chute Steering, Hydraulic

    200002176 DISCHARGE CHUTE STEERING, HYDRAULIC CH27 ACR & ACC...
  • Page 93 ST8.8ZN, M6X20, DIN933 52200078 Washer ST5.8ZN, M16, DIN125 200002171 Sliding part 52117165 Lock nut ST8.8ZN, M16, DIN985 200002174 Fastener 56518293 Hose assembly 1/4", 210 bar, K1/4"S L=2,4 m 200002179 Chain connector 5/8, 10B-1 40147010 Warning sticker "CUTTING HAZARD" CH27 ACR & ACC...
  • Page 94: 200002183 Discharge Chute Steering, Mechanical

    Description Remarks 200001478 Tightener flange 200001479 Intermediate flange 43295070 Tightener 52200052 Washer ST5.8ZN, M12, DIN125 52063047 Hex screw ST8.8ZN, M12X110, DIN931 52117124 Lock nut ST8.8ZN, M12, DIN985 54924890 Retainer lever 52062041 Hex screw ST8.8ZN, M12X50, DIN933 CH27 ACR & ACC...
  • Page 95: Acr Feeder

    ACR FEEDER Part Order no Description Remarks 200002101 Base 200002175 Feeder device 200002100 Side walls right and left Side shelters 200002230 Joint frame 200002214 Hydraulic hose kit CH27 ACR & ACC...
  • Page 96: Acc Feed Conveyor

    ACC FEED CONVEYOR Part Order no Description Remarks 200002175 Feeder device 200001339 Feed conveyor 200002100 Side walls right and left Side shelters 200002230 Joint frame 200004488 Hydraulic hose kit CH27 ACR & ACC...
  • Page 98: 200002175 Feeder Device

    200002175 FEEDER DEVICE CH27 ACR & ACC...
  • Page 99 ST8.8ZN, M12X30, DIN933 52110053 Hex nut ST8.8ZN, M12, DIN934 52117124 Lock nut ST8.8ZN, M12, DIN985 200001643 Flanged bearing 54923080 Vibration damper 1021692 200001997 Eye screw ST4.6ZN, M12x40, DIN444 52117108 Lock nut ST8.8ZN, M10, DIN985 200002163 Deck plating CH27 ACR & ACC...
  • Page 100: Side Shelters

    SIDE SHELTERS 9 10 CH27 ACR & ACC...
  • Page 101 200002143 Lock screw ST8.8ZN, M6x20, DIN 603 52117124 Lock nut ST8.8ZN, M12, DIN985 52200052 Washer ST5.8ZN, M12, DIN125 200001388 Lock screw ST8.8ZN, M12X35, DIN603 200004941 Drive rivet 4,0X12 200004875 Fastener incl. two pairs 200002124 Fastening plate CH27 ACR & ACC...
  • Page 102: 200002100 Side Walls Hf27

    200002100 SIDE WALLS HF27 Part Order no Description Remarks 200001400 Side wall right 200001388 Lock screw ST8.8ZN, M12X35, DIN603 200001843 Side wall left 52200052 Washer ST5.8ZN, M12, DIN125 52117124 Lock nut ST8.8ZN, M12, DIN985 CH27 ACR & ACC...
  • Page 103: 200002101 Acr Feeder Base

    ST8.8ZN, M12X35, DIN603 52117124 Lock nut ST8.8ZN, M12, DIN985 52200052 Washer ST5.8ZN, M12, DIN125 52001682 Hex socket cap screw ST8.8ZN, M8X35, DIN912 52200037 Washer ST5.8ZN, M8, DIN126 52117082 Lock nut ST8.8ZN, M8, DIN985 200001424 End plate CH27 ACR & ACC...
  • Page 104: 200002230 Joint Frame

    Lock nut ST8.8ZN, M24, DIN985 52854346 ZN, 25X63, NOR2850 52842168 Lynch pin ZN, 6,5X40, DIN11023 52401015 Grease fitting AR1/8, straight 52062114 Hex screw ST8.8ZN, M16X40, DIN933 52200078 Washer ST5.8ZN, M16, DIN125 52117165 Lock nut ST8.8ZN, M16, DIN985 CH27 ACR & ACC...
  • Page 106: 200001339 Feed Conveyor Acc

    200001339 FEED CONVEYOR ACC 10 11 CH27 ACR & ACC...
  • Page 107 ST5.8ZN, M8, DIN126 52117082 Lock nut ST8.8ZN, M8, DIN985 200002020 Support leg right 52390200 Usit seal ring 21,54x28,58x2,49, R 1/2" 52391034 Usit seal ring 13,74X20,57X2,03, R1/4" 52432101 Double fitting R1/4 52432051 Double fitting 1/2" - 1/2" CH27 ACR & ACC...
  • Page 108: 200002328 3Psl Support Legs

    200002328 3PSL SUPPORT LEGS CH27 ACR & ACC...
  • Page 109 52117249 Lock nut ST8.8ZN, M24, DIN985 52200102 Washer ST5.8ZN, M24, DIN126 52062379 Hex screw ST8.8ZN, M24X70, DIN933 200002533 Sticker Beware of support legs 200002702 Fastening plate 52401015 Grease fitting AR1/8 200003751 Top shelter 03288940 Hose kit CH27 ACR & ACC...
  • Page 110: 200002810 Feed Conveyor Bc3000 (Accessory)

    200002810 FEED CONVEYOR BC3000 (ACCESSORY) 48.1 48.1 48.1 48.2 3.13 3.14 3.6 3.9 48.1 3.7 3.3 3.12 3.11 3.11 3.12 3.14 3.15 3.16 3.15 3.10 48.1 48.1 CH27 ACR & ACC...
  • Page 111 18x415x3000MM 200000289 Conveyor belt 52090710 Hex socket cap screw ST8.8 BLACK, M12X40, DIN7991 52200052 Washer ST5.8ZN, M12, DIN125 52117124 Lock nut ST8.8ZN, M12, DIN985 52062031 Hex screw ST8.8ZN, M12X40, DIN933 52110079 Hex nut ST8.8ZN, M16, DIN934 CH27 ACR & ACC...
  • Page 112 49.02 40605214 Machine plate 49.03 30146990 Hand feed forbidden. sticker 49.04 40146900 Farmi forest sticker 49.05 200000999 BC3000 sticker 49.06 41014750 Read the instruction manual. sticker 200003166 Hydraulic hose kit includes all hoses and fittings CH27 ACR & ACC...
  • Page 113: 200002586 Oil Cooler (Accessory)

    ST5.8ZN, M10, DIN125 52060233 Hex screw ST8.8ZN, M10X30, DIN933 52117108 Lock nut ST8.8ZN, M10, DIN985 52200342 Washer ZN, M6, DIN440 52060456 Hex screw ST8.8ZN, M6X20, DIN933 33596100 Electrics 54946340 Cable 55119572 Relay 55119275 Relay base 54946010 Temperature switch CH27 ACR & ACC...
  • Page 114: 200002584 Hydraulic Unit Hd50 (Accessory)

    200002584 HYDRAULIC UNIT HD50 (ACCESSORY) 48.1 48.5 48.2 48.3 48.4 CH27 ACR & ACC...
  • Page 115 1 1/4", 5 bar 52442175 Elbow fitting R1/2, 90º 52442183 Elbow fitting R3/4, 90º 52432044 Double fitting R1/2-3/4 52390622 Usit seal ring U42,93X52,38X2,5, 52390580 Usit seal ring 27,05X34,93X2,49, R3/4" 52063252 Hex screw ST8.8 BLACK, M16X50, DIN933 CH27 ACR & ACC...
  • Page 116 Hex screw ST8.8ZN, M8X16, DIN933 FROM MACHINE: 000074 chip length max. 20 mm, 43489940 Belt pulley, standard D190 54822930 V belt, standard XPA 1030 chip length 20-25 mm 43489890 Belt pulley D245 200002607 V belt XPA 1150 CH27 ACR & ACC...
  • Page 118: 200002589 Emk27 Stationary Chipper Platform (Accessory)

    200002589 EMK27 STATIONARY CHIPPER PLATFORM (ACCESSORY) 36 35 33 34 45 46 19 18 18 CH27 ACR & ACC...
  • Page 119 ST8.8ZN, M12X35, DIN933 52200045 Washer ST5.8ZN, M10, DIN125 52117249 Lock nut ST8.8ZN, M24, DIN985 52200102 Washer ST5.8ZN, M24, DIN126 52200078 Washer ST5.8ZN, M16, DIN125 52062122 Hex screw ST8.8ZN, M16X50, DIN933 200002504 Farmi profi sticker 200002464 Cutting hazard sticker CH27 ACR & ACC...
  • Page 120 Electric motor 75kW 58221570 Belt pulley 53220290 Cone sleeve 03298550 Starter 75kW, 400V 54810640 Universal shaft 1 3/4 - 1 3/4, L=860 45638910 Power source 230VAC/12V 55130790 Adapter cable 120W, 12V, 3-POLE / 7-POLE 53 54 CH27 ACR & ACC...
  • Page 121: 200002373 Cross Breaker (Accessory)

    200002373 CROSS BREAKER (ACCESSORY) CH27 ACR & ACC...
  • Page 123 The warranty does not cover wearing parts. Send faulty parts, carriage paid, to the manufacturer for inspection. Repairs will be conducted by Farmi Forest Oy or an authorized expert. The warranty is valid only if the bottom part of this page is filled in and returned to the manu- facturer within 30 days of receipt of the product.
  • Page 124: Product Registration Form

    Date of delivery:_____/_____ 20_____ Dealer: Dealer’s address: Dealer’s tel: Product and type: Serial number: Return to the manufacturer Date of delivery:_____/_____ 20_____ Dealer: Dealer’s address: Dealer’s tel: Customer: Customer’s address: Customer’s tel: E-mail: Product and type: Serial number: CH27 ACR & ACC...
  • Page 125 Farmi Forest representatives: Western Europe Austria Belgium & Luxemburg Esch-Technik Maschinenhandel G.m.b.H. Déom Sa Klagenfurter Str. 129 Rue de Monty, 177 Sankt Veit an der Glan B-6890 Libin A-9300 Austria Tel. +32 (0)61 65 00 20 Tel. +43 4212 29600 contact@deom.be...
  • Page 126 CH-9554 Tägerschen TG Aydinli Tuzla Istanbul Tel. +41 (0) 71 918 8020 Tel. +90 216 593 09 42 info@adbachmannag.ch mustafa.kemal@rekarma.com adbachmannag.ch rekarma.com.tr Farmi Forest representatives: Eastern Europe Estonia Belarus Melit AP Oü TIGER Ltd Punane 6-311 Kozlova Lane 25-17 13619 Tallinn Minsk 220037 Tel.
  • Page 127 Farmi Forest representatives: North and South America Argentina Canada Inderfor S.A. MTI Canada Inc. Pasco 1732 - 10º "A" 2000 Rosario 1720 Boulevard Guillaume-Couture SANTA FE Saint-Romuald Lévis QC G6W 0R5 Tel. +54 (0)341 679 25 66 Tel. 418 839-4127 info@inderfor.com...
  • Page 128 Farmi Forest Ahmolantie 6, 74510 IISALMI, FINLAND +358 (0)17 832 4400, info@farmiforest.fi...

This manual is also suitable for:

Ch27 acc

Table of Contents