Table of Contents
Advertisement
TROUBLESHOOTING/REPLACEMENT PARTS
When this happens
Others
You feel electricity a little when touching
● The refrigerator may be charged with static electricity, but there is no problem with the safety.
the main body of the refrigerator
→ It is recommended to ground if you want to remove it.
● It is caused by the electromagnetic radiation slightly generated from this refrigerator.
Radio and/or television
→ Install the refrigerator away from the television, radio and interphone.
→ It is recommended to connect the power plug to the power outlet separated from the antenna terminal and
are disturbed by noises
● Those lines are caused by the liquid resin fl owing when plastic is molded.
There are thin lines like
scratches on the plastic parts
There are waving and/or distortions
● Slight waving and/or distortions are generated in the manufacturing process of the refrigerator.
on the door surface, the side and the
top surface of the refrigerator.
The Control
● Approximately two minutes after the end of operation, indicator lamps, excluding 急冷凍 (Quick Freezing) , 急冷藏 (Quick Cooling) ,
Panel is unlit.
A magnet does not
● A magnet does not adhere because the door is made of glass.
adhere to the door
● This hole is used to escape the air inside when fi lling the heat insulation material into the
There is a small hole
inside the door
The electric supply failed
● Reduce the number of times of opening and closing the door and avoid storing food additionally until the electric supply is restored.
The refrigerator is not expected
● Unplug the power plug and maintain the inner of the refrigerator and the Automatic Ice Maker, and leave all
to use for a long term
● Any operation to remove frost is not required because this refrigerator remove frost automatically.
Remove frost
Transporting and moving care
● See " Transporting your refrigerator (transport for moving) "
When you want
● A lower setting of the condensation prevention heater will reduce power consumption.
to lower the
● The setting will be cancelled when the power plug is connected and disconnected or power failure recovery takes place.
setting of the
● Setting the swing partition
condensation
1. Open the Lower Freezer Door.
prevention
2. Press and hold the
heater (the swing
3. Press and hold the
partition and the
4. Close the lower Freezer Door.
partitioning iron
● Setting the partition plate
plates)
1. Open the door of the lower freezer
2. With the door of the Refrigerator Compartment closed, touch and hold the
Swing
3. Touch and hold the
partition
4. Close the door of the Refrigerator Compartment.
Partitioning
To cancel the setting, perform the same operation at Level 2.
iron plates
Alarm is raised (two beeps sound) to cancel the setting.
Temperature settings for Refrigerator, Freezer and Vegetable Compartments can
be adjusted more fi nely than the three levels: 弱 (MIN) , 中 (MID) and 強 (MAX) .
1. Open the Lower Freezer Door.
When you want
2. Touch and hold the
to adjust the
3. Adjust the
temperature
more fi nely
4. If you want to stop the fi ne adjustment, perform the operation of 1 and 2.
REPLACEMENT PARTS
When replacing the following parts, make sure to tell your dealer the type name and buy the special parts.
Replacing the water fi lter
● Replace the water fi lter when it becomes old.
(Replace it normally once 3 〜 4 years.)
● Ordering the replacement water fi lter
Tell your dealer the parts number: RJK-30 to buy the
replacement water fi lter. (Ice making capacity is the
same with the water fi lter removed.)
ground the refrigerator.
Pg.37
They are especially conspicuous for the transparent parts, but there is no problem with the strength and they
can never lead to any cracks.
They may be conspicuous according to the position of the light source and/or the brightness etc., but there is
no problem with the performance.
節電 (Energy Saving) , 急速製冰 (Quick Ice Making) , 給水 (Water Supply) and eco Operation , become unlit for energy saves.
door during the production process. It is neither a fl aw nor abnormal thing.
the door open to dry the refrigerator for 2 〜 3 days.
Thawed water is collected in the evaporating tray and automatically evaporates.
The setting has two levels: 1 and 2. The level 2 achieves a higher reduction in power consumption. A lower setting of the condensation prevention
heater may cause dew condensation in the swing partition or the partitioning iron plates when humidity is high. When dew is formed, cancel the setting.
button on the Control Panel with the refrigerator
doors closed for three seconds or more until one beep sounds. (Level 1)
button on the Control Panel for three seconds or
more until two beeps sound. (Level 2)
button on the control panel for 3 seconds or longer until it beeps (Level 1).
button on the control panel for 3 seconds or longer
until it beeps (Level 2).
Level 1 for saving electricity
button on the Control Panel for fi ve seconds or
more until one beep sounds (This allows fi ner adjustment.)
,
or
button to make an adjustment. The temperature
becomes higher by one level every time you touch the button. (Touching 強
(MAX) returns to 弱 (MIN) .)
Two beeps sound and You can set the temperature by normal step.
Please check. This is the cause.
Pg.37
Pg.43, 49, 51〜53
Pg.37
Level 2 for saving electricity
Replacement of the vacuum packing
● If vacuum state can no longer be maintained due to damage,
deformation or a change in color, please replace it with a new one.
● Part number for each refrigerator model
Type: R-SF8800B
R-SF6800B
Hole (inside of the door)
Touch this button for more than 3 seconds
Touch this button for more than 3 seconds
Deactivate
MIN MID-
MID MID-
MIN
Temperature setting
Parts number
R-B6700 311
R-A6200 321
About 3
seconds
About 3
seconds
MAX
MAX
57
Advertisement
Table of Contents
