Related Manuals for Spektrum Firma SPMXSE1070
Summary of Contents for Spektrum Firma SPMXSE1070
- Page 1 Spektrum Firma 70A Brushed Smart ESC Spektrum Firma 70A Brushed Smart Regler Spektrum Firma 70A Contrôleur à balais Smart Spektrum Firma 70A Smart Brushed ESC...
- Page 2 SPMXSE1070 Scan the QR code and select the Manuals and Support quick links from the product page for the most up-to-date manual information. Scannen Sie den QR-Code und wählen Sie auf der Produktseite die Quicklinks Handbücher und Unterstützung, um die aktuellsten Informationen zu Handbücher.
- Page 3 NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com or towerhobbies.com and click on the support or resources tab for this product. MEANING OF SPECIAL LANGUAGE The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:...
-
Page 4: Waterproof Component
Hobby disclaims all liability outside of the intended purpose and will not provide warranty service related thereto. Waterproof Component Your new Spektrum 70A Brushed Waterproof ESC has been ® designed and built to allow you to operate the product in many “wet conditions,”... -
Page 5: General Precautions
CAUTION: Failure to exercise caution while using this product and comply with the following precautions could result in product malfunction and/or void the warranty. GENERAL PRECAUTIONS • Read through the wet conditions maintenance procedures and make sure that you have all the tools you will need to properly maintain your ESC. -
Page 6: Wet Conditions Maintenance
ing water, or frequent, intermittent immersion of waterproof component(s). • 1 hour continuous operation in damp sand, dirt, mud or snow (the material level should always be below the vehicle frame), constant splatter without any immersion or coverage of water- proof component(s). -
Page 7: Table Of Contents
Contents Waterproof Component ............4 General Precautions ............5 Usage Conditions .............. 5 Wet Conditions Maintenance ..........6 System Specifications ............8 Wiring Diagram ..............9 Installation ................ 10 ESC and Transmitter Calibration ......... 10 Operation ................. 11 ESC Programming via Switch Push Button ......12 Programming the ESC via the SPMXCA200 Program Box .. -
Page 8: System Specifications
System Specifications Type Brushed Constant/Peak 70A/200A Forward/Reverse; Forward/Brake/ Reverse, Forward/Brake Function (Can be programmed via SPMXCA200 or through the push button on the switch) Programming Port Optional Programming Box (2) Standard Female Servo Con- Auxiliary Power nectors for Lights, etc @ 6V/7.4V Outputs (Power Supplied by BEC) 1/10 On-Road, Off-Road, Scaler,... -
Page 9: Wiring Diagram
Wiring Diagram Auxiliary (Light) Connectors Programming Port Heatsink Power Programming Button Throttle Connector to Bullet Receiver Connectors Between ESC IC3 Power and Motor Input Connector NOTICE: Always disconnect the battery from the ESC when you have finished operating your vehicle. If you leave the battery connected with the power switch in the OFF position, the ESC will continue to draw current when connected to the battery, resulting in possible damage to the battery through... -
Page 10: Installation
Installation 1. Determine how to mount the ESC as specified by your vehicle’s instruction manual, or in an area with adequate airflow and protection from damage. Ensure all wiring connections can be reached prior to mounting. 2. Use double-sided foam tape or the mounting tabs with screws on the bottom of the case to secure the ESC in position. -
Page 11: Operation
3. Press and hold the programming button on the switch case, power on the ESC. The red LED on the ESC will flash, and the motor will beep. Release the programming button. The ESC will enter the programming mode if the programming button is not released within 3 seconds. -
Page 12: Esc Programming Via Switch Push Button
ESC Programming via Switch Push Button 1. Power ON your transmitter. Connect a battery to the ESC and power it ON. NOTICE: The transmitter and receiver must be connected. 2. Press and hold the programming button for 1 second. OPTIONAL: Press and hold the programming button for 5 seconds to reset all ESC programming options. -
Page 13: Programming The Esc Via The Spmxca200 Program Box
Programming the ESC via the SPMXCA200 Program Box 1. Begin with no battery connected. 2. Connect the cable for the programming box into the program- ming port as shown. 3. Connect a battery and power ON the ESC. OPTIONAL: The ESC settings can be reset to default by press- ing “Reset”... -
Page 14: Programmable Features
Programmable Features 1. Running Mode 2. Lipo Battery 3. Cutoff Voltage 4. Initial Start Force (%) 5. Max Forward Force (%) 6. Max Reverse Force (%) 7. Max Brake Force (%) 8. Initial Brake Force (%) 9. Drag Brake (%) 10. -
Page 16: Led Indicator And Motor Sounds
LED Indicator and Motor Sounds Upon powering on the ESC, the LED will blink and the motor will emit a series of beeps to indicate its status. First it will display the battery mode selection, second the drag brake setting, and then it will indicate it is ready to operate. Feature LED Status Motor Sound... -
Page 17: Troubleshooting Guide
Troubleshooting Guide Problem Possible Cause Solution Recharge/replace Battery/connec- battery. Secure all ESC ON – No tion issue connections motor function, audible tone or Damaged ESC/ Repair/replace ESC switch switch/ESC Damaged motor Repair/replace When the ESC LED Low voltage blinks, recharge/ protection replace battery Motor –... - Page 18 Troubleshooting Guide Problem Possible Cause Solution Test the motor apart from the vehicle Damaged motor system, repair/replace motor as needed Steering Servo – Operates; motor Adjust throttle travel/ does not run Incorrect other throttle settings transmitter/ESC on the transmitter/ calibration ESC.
-
Page 19: 1-Year Limited Warranty
1-Year Limited Warranty What this Warranty Covers – Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship for a period of 1 year from the date of purchase. What is Not Covered –... - Page 20 LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted.
- Page 21 a Return Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our facility.
-
Page 22: Warranty And Service Contact Information
Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition you will be billed for return freight. Horizon accepts money orders and cashier’s checks, as well as Visa, Mas- terCard, American Express, and Discover cards. By submitting any item to Horizon for service, you are agreeing to Horizon’s Terms and Conditions found on our website http://www.horizonhobby. -
Page 23: Fcc Information
FCC Information SUPPLIER’S DECLARATION OF CONFORMITY Firma 70A Brushed Crawler Smart ESC (SPMXSE1070): This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interfer- ence that may cause undesired operation. -
Page 24: Ic Information
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. •... - Page 25 Compliance Information for the European Union EU COMPLIANCE STATEMENT Firma 70A Brushed Crawler Smart ESC (SPMXSE1070): Hereby, Horizon Hobby, LLC declares that the device is in compliance with the following: 2014/30/EU EMC Directive; RoHS 2 Directive 2011/65/EU; RoHS 3 Directive - Amending 2011/65/EU Annex II 2015/863.
- Page 26 DSM2, DSMR, the Smart Technology logo, and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bach- mann Industries, Inc. All other trademarks, service marks and logos are property of their respective owners.