Stihl FSA 135 R Instruction Manual page 8

English
4.6.2 Deflector
The deflector is in a safe condition if the following
points are observed:
– The deflector is not damaged.
– If you are using the line limiting blade and
skirt: Line limiting blade and skirt are correctly
fitted.
WARNING
■ If components do not comply with safety
requirements, they will no longer function
properly and safety devices may be rendered
inoperative. This can result in serious injuries.
► Work only with an undamaged deflector.
► If you are using the line limiting blade and
skirt: Work with a correctly fitted line limiting
blade and skirt.
► If you have any queries: Contact your
STIHL servicing dealer.
4.6.3 Mowing Head
The mowing head is in a safe condition if the fol‐
lowing points are observed:
– The mowing head is not damaged.
– The mowing head is not jammed.
– The mowing lines are properly installed.
– The wear limits are not exceeded.
WARNING
■ If they are in an unsafe condition, parts of the
mowing head or mowing lines may come off
and be ejected at high speed. They may
cause serious injury to persons.
► Work only with an undamaged mowing
head.
► Never use metal objects in place of the
nylon mowing lines.
► Observe and remain inside the wear limits.
► If you have any doubts, be sure to consult a
STIHL dealer.
4.6.4 Metal cutting attachment
The metal cutting attachment is in a safe condi‐
tion if the following points are observed:
– Metal cutting attachment and mounting hard‐
ware are undamaged.
– Metal cutting attachment is not warped.
– Metal cutting attachment is properly mounted.
– Metal cutting attachment is correctly sharp‐
ened.
– Cutting edges of the metal cutting attachment
have no burrs.
– The wear limits are not exceeded.
– If a metal cutting attachment not manufactured
by STIHL is used, it must not be heavier,
thicker, of a different shape, of a lower quality,
8
or larger in diameter than the largest metal
cutting attachment approved by STIHL.
WARNING
■ If it is not in an safe condition, parts of the
metal cutting attachment may come off and be
thrown at high speed. They may cause serious
injury to persons.
► Never work with a damaged metal cutting
attachment or damaged mounting hard‐
ware.
► Sharpen the metal cutting attachment cor‐
rectly.
► Deburr the cutting edges with a file.
► Have the metal cutting attachment bal‐
anced by a STIHL servicing dealer.
► Observe and remain inside the wear limits.
► Use a metal cutting attachment specified in
these instructions for use.
► If you have any doubts, be sure to consult a
STIHL dealer.
4.6.5 Battery
The battery is in safe condition when the follow‐
ing conditions are met:
– The battery is not damaged.
– The battery is clean and dry.
– The battery is working and has not been modi‐
fied.
WARNING
■ The battery cannot function safely if it is not in
safe condition. There is a risk of serious injury
to persons.
► Use an undamaged and functioning battery.
► Do not charge a damaged or defective bat‐
tery.
► If the battery is dirty or wet: clean the bat‐
tery and allow it to dry.
► Do not modify the battery.
► Do not insert objects into the apertures in
the battery.
► Never connect the battery terminals to met‐
allic objects and cause a short circuit.
► Do not open the battery.
► Replace worn or damaged warning signs.
■ Fluid may leak from a damaged battery. If the
fluid contacts the skin or eyes, this may cause
irritation.
► Avoid contact with the fluid.
► In the event of contact with the skin: wash
the affected areas with plenty of soap and
water.
► In the event of contact with the eyes: rinse
the eyes with plenty of water for at least 15
minutes and seek medical attention.
4 Safety Precautions
0458-662-0121-C