Page 1
SBC-EC9100 Evaluation Board User Manual Rev00...
Page 2
The core board of SOM-PH8800 and related intellectual property owned by Shenzhen EMBEST Technology Co. Ltd. Shenzhen Embest Technology has the copyright of this document and reserves all rights. Any part of the document should not be modified, distributed or duplicated in any approach and form with the written permission issued by Embest Technology Co., Ltd.
Chapter 1 Product Overview 1.1 Brief Introduction SBC-EC9100 is low cost evaluation board that using i.MX6UL processor by Embest design. The system is oriented to the industrial embedded control field, such as medical instrument, video monitor, communication and so on. Which is industrial embedded products without too much UE for human-computer interaction.SBC-EC9100 provides a rich resource of peripheral interfaces, with one...
Chapter 2 Introduction to Hardware System This chapter will do some detailed description about SBC-EC9100 hardware system structure 、 extend and peripheral interface,if there are some difference description between chip datasheet and this chapter chip description,please refere to official chip datasheet.
Page 12
BOOT_MODE[1:0] , Boot_MODE[1:0] defined as follows: SBC-EC9100 use 2 bits for encoding the switch SW3 as boot mode choice, the switch to off position, using the chip internal pull-down, logic is set to 0, the switch to on, use external 10K, logic is set to 1, as shown in the figure on the right:.
Page 14
Embest Technology. Special note, SBC-EC9100 has a factory mode, when the set of internal start and restore the start (if already open) are failure, SBC-EC9100 can enter the SD/MMC start before downloaded mode, and the process is as follows: ◆Reset Circuit...
Power ◆Power Supply The SBC-EC9100 connected power input DC5V, with 5.5V overvoltage protection, 4a over current protection, power supply reverse connection protection function, input supply system directly start and normal green power indicator light, start running the green lights flashing, for close to press the on / off...
Embest Technology. ◆RTC Power PF3001 has RTC power management function, but need to provide external power supply, SBC-EC9100 no design board RTC battery, the use of external RTC power design, as follows: 1.2 External Interface Detail 1.2.1 RS485 Interface SBC-EC9100 provides one RS485 interface, the transceiver chip using Devices ADM3485...
The processor using Uart1 to achieve RS485 communication, while increasing the ESD protection circuit, RS485 signal through the industrial interface J9 to connect exterior, the corresponding schematic design is as follows: 1.2.2 CAN Interface SBC-EC9100 can provide two interfaces, which requires to connect to external SPI signal multiplexing, select J203 by manual selection, the default state for the use of SPI signals.
Embest Technology. 1.2.3 Ethernet Interface SBC-EC9100 provides a complete 100M Ethernet interface, while also providing one way with the GPIO function of the RMII interface. 100M Ethernet interface using the PHY transceiver for KSZ8081 MICREL, the functional block diagram as follows:...
1.2.5 LCD &Touch Screen Controller Based on the positioning of design, SBC-EC9100 does not provide a powerful video display function, only to provide a 24bit LCD HDMI display interface, for the basic LVDS. Output interface using the 50pin FPC flat cable seat, IO level for 3.3V and support the company's LCD8000-43T (4.3 inch screen) and LCD8000-70T (7 inch screen).
Page 26
LCD_PWM Control Ground About Touch functions of SBC-EC9100, subject to resource constraints, using SPI interface to complete the touch screen function instead of CPU comes with TSC functional module, using TI's TSC2016 connection resistance touch screen by default as bellows:.
FPC connector(J5). 1.2.6 CAMERA The J6 of SBC-EC9100 is the FPC connector to be used to support the highest 12 digit digital camera input. The voltage level is 3.3V. The following table is the FPC connector J6 signal pin definition table:...
Embest Technology. 1.2.7 TF Card SBC-EC9100 can be used for curing TF card interface, storage startup code and program system, using MMC interface.Its interface is defined as shown below: Table 1-1 TF card interface TF card connector: J2 Signal Description...
Page 31
◆I2S i.MX 6UltraLite processor synchronous audio interface (SAI) to support the full duplex serial interface, such as I2S, AC97, TDM, etc.. The extend interface of SBC-EC9100 provide a interface, easy to connect the audio function, I2S signal connect wth others by...
Page 32
QSPI signal is connected to the J9 socket, QSPI signal and FLASH NAND signal multiplexing, the schematic as follows: ◆RMII SBC-EC9100 not only boardload one 10M/100M Ethernet, but also can be extended to the J10 socket and to get a complete function of the RMII signal SBC-EC9100 User Manual...
Page 33
The schemetic design as bellows: ◆Uart SBC-EC9100 expansion J9 and J10 socket have Uart signal output, both TTL level. One of the Uart J10 default for the debug serial port, and Rpi socket compatible with the debug information obtained from here. Connect the cable to recommend the use of our company's USB...
◆ON/OFF Buttom SBC-EC9100 besides the reset button, but also there is the design of a power ON/OFF SW2 button, when the system is connected to the external power supply, the default state is ON, that is, when the power is not pressed the ON/OFF button to boot.
CPU Pad (BGA 14 x 14 mm) System RUN UART_RTS 1.2.11 Wifi SBC-EC9100 board set aside an industrial grade BLE & Wifi module, the function block diagram as follows: ◆WIFI Parameter Integrated 2.4 & 5G GHz Power Amplifier (PA) for WLAN solution ●...
Page 37
Warranty Conditions 1) 12-month free warranty on the PCB under normal conditions of use since the sales of the product; 2) The following conditions are not covered by free services; Embest Technology will charge accordingly: Customers fail to provide valid purchase vouchers or the product identification tag is damaged, ...
Page 38
3) Within the period of warranty, the freight for sending products from customers to Embest Technology should be paid by customers; the freight from Embest to customers should be paid by us. The freight in any direction occurs after warranty period should be paid by customers;...
Need help?
Do you have a question about the SBC-EC9100 and is the answer not in the manual?
Questions and answers