SECOLink KM24 Short User Manual page 7

Intruder alarm system
key LED
Available backlight modes for
Off –
Pre-Alarm status –
, [Settings]
ENT ENT ENT ENT
[[ ] key LED] ,
Events from zones
This menu is visible when in above mentioned LCD display or keypad interface settings the option "By
zone" has been selected. The key
, [Settings]
ENT ENT ENT ENT
[Events from zones [ENT]]
Entry/exit sounds
When the entry/exit delay is in progress, the remaining time is shown on keypad displays, the sound signal
is audible. It is possible to turn ON this sound signal on certain keypad and to turn OFF on the other one. In
order to do it mark/unmark the partitions by "+" sign pressing the
, [Settings]
ENT ENT ENT ENT
[Entry/Exit sounds [ENT]] ,
Interface example
A major benefit of the keypad is that it interface can be very easily customized. An example describes the
keypad interface setup, when the keypad is installed in the bedroom. The bright light source and the
additional sounds, excluding an alarm, are not allowed in this room. The keypad LCD brightness and
contrast levels will be reduced. LCD and keypad key backlight will be automatically turned Off when the
keypad is not in use for last 40 seconds. The
Interface settings:
LCD backlight – By zone (see "LCD display and keypad key backlight modes");
Keypad backlight – By zone (see "LCD display and keypad key backlight modes");
Example Status LEDs status – Always (see "Status LEDs");
key LED – Armed (see " key LED");
key LED – Off (see " key LED");
key LED – Off (see " key LED");
B B B B B B B B ! ! ! ! ! ! ! !
BY BY BY BY BY BY BY BY
key LED – Off (see " key LED");
Events from zones – no zones are marked (see "Events from zones");
Entry/Exit sounds – no partitions are marked (see "Entry/exit sounds");
LCD brightness level – 7 (see "LCD display brightness and contrast");
LCD contrast level – 7 (see "LCD display brightness and contrast");
Help texts
Keypad is equipped with a special
pressing this key user can find information how to manage a system or problem.
10-26 +25°C
READY TO ARM READY TO ARM
1st Floor
2nd Floor
Press key.
Information about system
Information about system, central monitoring station, installer, power supply voltages can be found in
information menu. In order to enter this menu user must press
view. Choose the corresponding menu, enter it by pressing
key LED is always Off ;
key LED is steady On, when the partition is secured with "Pre-alarm" mode On.
, [Keypad Settings]
ENT ENT ENT ENT
, .
ENT ENT ENT ENT ENT ENT ENT ENT
, [Keypad Settings]
ENT ENT ENT ENT
,
ENT ENT ENT ENT
, [Keypad Settings]
ENT ENT ENT ENT
ENT ENT ENT ENT
B B B B B B B B ! ! ! ! ! ! ! !
BY BY BY BY BY BY BY BY
01:44
Arming Arming
Away Away
Press [ENT] to arm
Press [ ] to select mode
Press [1]..[4] to select part.
key will start to blink. It means that
? ? ? ? ? ? ? ?
there is a help text is available for
the Away arming mode. Press
key to read the help text.
key:
, [Light & Indication]
ENT ENT ENT ENT
is used to mark/unmark the zone.
# # # # # # # # # # # # # # # #
, [Light & Indication]
ENT ENT ENT ENT
, .
# # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # ENT ENT ENT ENT
, [Light & Indication]
ENT ENT ENT ENT
, .
# # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # ENT ENT ENT ENT
key will be used for a status indication.
key. The key LED blinks if there is some additional information. By
? ? ? ? ? ? ? ?
This arming mode is used
when you want to protect
a premise, when nobody
will be staying inside. After
arming, all zones will be
protected. After using the
door will be entry delay
Use or
? ? ? ? ? ? ? ?
KM24, KM24A keypad KM24, KM24A keypad
, [Enter PIN]
ENT ENT ENT ENT
, [Enter PIN]
ENT ENT ENT ENT
key.
# # # # # # # # # # # # # # # #
, [Enter PIN]
ENT ENT ENT ENT
time for disarming.
Press [CLR] to exit.
for navigation.
key when keypad is showing main display
? ? ? ?
key.
ENT ENT ENT ENT
Short user manual
,
PIN: PIN: PIN: PIN:
,
PIN: PIN: PIN: PIN:
,
PIN: PIN: PIN: PIN:
Press to exit.
CLR CLR CLR CLR CLR CLR CLR CLR
7