Related Manuals for pellenc C45
Summary of Contents for pellenc C45
- Page 1 Translation of the original op- erating instructions manual PRUNING SHEARS 163529-A Operating instructions 01/2022 READ THE USER GUIDE CAREFULLY BEFORE USE...
-
Page 3: Table Of Contents
2.6. PERSONAL PROTECTION EQUIPMENT ..................3. DESCRIPTION AND TECHNICAL FEATURES ..............10 3.1. DESCRIPTION OF THE TOOL ...................... 3.2. TECHNICAL FEATURES OF THE PRUNING SHEARS C45 ............4. COMMISSIONING ......................... 12 4.1. CONNECTING THE TOOL TO THE BATTERY ................4.2. TURNING ON THE TOOL WITH ACTIVSECURITY ACTIVATED (FACTORY SETTING) ... - Page 4 6.8.2. FITTING OF THE BLADE AND ITS PINS ..................7. INCIDENTS AND TROUBLESHOOTING ................28 7.1. SUMMARY OF "ACTIVSECURITY" LED CODES AND AUDIBLE SIGNALS ......7.2. SUMMARY OF BATTERY LED CODES ON PRUNING SHEARS C45 ........7.3. TROUBLESHOOTING ........................8. TRANSPORT / STORAGE ....................29 8.1.
-
Page 5: Introduction
PRUNING SHEARS C45 163529-A 1. INTRODUCTION Dear Customer, Thank you for purchasing your Pruning shears C45. Properly used and maintained, this equipment will give you years of satisfaction. Warning Your machine contains numerous recoverable or recyclable materials. Return it to your dealer or, failing this, to an approved servicing centre to be treated. -
Page 6: Safety
• The Pruning shears C45 is intended for wine and tree pruning, up to a diameter of 45 mm. • The Pruning shears C45 must be operated from standing ground level or from a suitable platform that is completely stable and secure. -
Page 7: Personal Safety
PRUNING SHEARS C45 163529-A 2.2.3. PERSONAL SAFETY Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. -
Page 8: Servicing
2.2.7. MANAGEMENT OF THE RECYCLING AND RECOVERY OF WASTE FROM YOUR TOOL When the tool reaches the end of its life, PELLENC keeps the end of life sheet of the equipment at disposal. The end of life sheet provides instructions for safely removing components. -
Page 9: Safety Warnings For Battery-Powered Shears
Warning Read all the instructions on the ActivSecurity of your Pruning shears C45 carefully before use, see Section 5.2, “Tool safety”. Never modify the connector in any way whatsoever. -
Page 10: Personal Protection Equipment
PRUNING SHEARS C45 163529-A 2.6. PERSONAL PROTECTION EQUIPMENT Equipment Wearing of Safety helmet Protective visor Pellenc ActivSecurity gloves Recommended Safety footwear Mandatory Ear protection Protective goggles Recommended Jacket or over-sleeves Work trousers 3. DESCRIPTION AND TECHNICAL FEATURES 3.1. DESCRIPTION OF THE TOOL... -
Page 11: Technical Features Of The Pruning Shears C45
Knurled adjustment washer 12. Optical sensor Blade 13. Lower conductive pad Hook 14. Power cord connector 3.2. TECHNICAL FEATURES OF THE PRUNING SHEARS C45 Cutting capacity 45 mm Pruning shears power supply voltage 43.2 V Motor rated power 180 W... -
Page 12: Commissioning
PRUNING SHEARS C45 163529-A 4. COMMISSIONING Note For further information on commissioning instructions, please refer to the operating instructions of the battery. 4.1. CONNECTING THE TOOL TO THE BATTERY To commission the battery, refer to its operating in- structions. Make sure the battery is switched off before plug- ging in the tool. -
Page 13: Turning On The Tool With Activsecurity Disabled
PRUNING SHEARS C45 163529-A 4.3. TURNING ON THE TOOL WITH ACTIVSECURITY DISABLED Turn on the battery by pressing the on/off button and wait for the battery to beep 5 times. The "ActivSecurity" LED flashes red. Take the tool in hand and pull the trigger. -
Page 14: Activation Of Activsecurity
5.2.2. ACTIVATION OF ACTIVSECURITY Warning ActivSecurity is based on electrical conduction and is only optimal with the use of Pellenc Ac- tivSecurity Gloves. When working in wet conditions, wearing gloves increases safety effectiveness. If you put on gloves that you did not have at the beginning of the day, or if you change your conductive gloves during the day, make sure they are compatible with the ActivSecurity system by restarting the tool and activating the security. -
Page 15: Checking The Activsecurity System
In the event of any problem, consult an authorized distributor PELLENC. Warning For the proper functioning of the safety system, it is imperative to wear Pellenc ActivSecurity gloves or no gloves at all. The use of any other gloves is prohibited. -
Page 16: Optical Trigger - Half Opening
PRUNING SHEARS C45 163529-A Once the tool has been activated, ensure that the Ac- tivSecurity system is working properly: Take the tool in your hand, making sure that your fingers are in contact with one of the two conductive pads (1). -
Page 17: Usage Modes
PRUNING SHEARS C45 163529-A 5.4. USAGE MODES When leaving the factory, the pruning shears are set in "progressive" mode (C2). 5.4.1. CHANGING USAGE MODE Turn the battery on, with the tool connected, Press the "mode" button, Select modes C1, C2, C3 or C4 by pressing + or -, Press the "mode"... - Page 18 PRUNING SHEARS C45 163529-A Mode C2: PROGRESSIVE (factory mode) • Progressive operation without half-opening. Mode C3: ON/Off HALF-OPENING • Fast, "On/Off" operation, with half-opening. Mode C4: ON/Off • Fast On/Off operation without half-opening.
-
Page 19: Functional" Settings Modes
PRUNING SHEARS C45 163529-A 5.5. "FUNCTIONAL" SETTINGS MODES 5.5.1. CHANGING THE "FUNCTIONAL" SETTINGS MODE Turn the battery on, with the tool connected, Press the "mode" button, Select the mode by pressing + or -, Press the "mode" button to validate, Press + or - to adjust the setting from 1 to 9, see Section 5.5.2, “Presentation of "functional"... -
Page 20: Presentation Of "Functional" Settings Modes
PRUNING SHEARS C45 163529-A 5.5.2. PRESENTATION OF "FUNCTIONAL" SETTINGS MODES Pruning shears mode Description Adjusting the setting F5: Blade crossing setting Adjust the blade crossing. 1 - 9: Low crossing - high crossing F6: Adjusting the half-opening Adjust the blade half-opening. -
Page 21: Compatibility: Battery Mode And Model
F7: Adjusting optical sensor sensitivity F8: Tool standby delay setting 5.7. STANDBY Putting the Pruning shears C45 into standby is possible when the F8 mode is set between 1 and 8, see Section 5.5, “"Functional" settings modes”. Note A beep from the battery indicates that the tool is in standby mode. -
Page 22: Standby Exit
Caution Always disconnect the tool battery before starting tool maintenance. • Use products recommended by PELLENC. • In the event of any problem, consult an authorized distributor PELLENC. -
Page 23: Maintenance Table
PRUNING SHEARS C45 163529-A 6.2. MAINTENANCE TABLE At each Maintenance task Every 4 hours Every week After each use start-up Sharpening the blade, see Section 6.3, “Sharpen- ing the blade”. Check the tightening of the blade, see Sec- tion 6.4, “Check the tightening of the blade”. -
Page 24: Check The Tightening Of The Blade
PRUNING SHEARS C45 163529-A Use the sharpening stone provided. Refresh only the 1st cutting angle (1) from the in- side to the outside until the burr is removed from the blade edge. Important Incline the stone about 30° to match the edge of the blade perfectly. -
Page 25: Checking The Crossing Over Of The Hook And The Blade
PRUNING SHEARS C45 163529-A 6.6. CHECKING THE CROSSING OVER OF THE HOOK AND THE BLADE Ensure that in the closed position the tip of the blade is in the lower third of the hook. Adjust the crossing if necessary, see Section 5.5, “"Functional"... -
Page 26: Fitting Of The Blade And Its Pins
PRUNING SHEARS C45 163529-A Unscrew the nut (2) with the supplied wrench (3) and remove the nut (2). Remove the parts in this order: • The blade pin (4), • The washer (5), • The knurled adjustment washer (6), • The circlip (7) by levering with a small screwdriver and then the shoulder pin (8). - Page 27 PRUNING SHEARS C45 163529-A Align the flat on the blade shaft (5) with the blade marker (2). Fit the blade pin (5). Refit the knurled adjusting washer (6) and then the washer (7). 10. Position and screw the nut (8) onto the blade shaft (5) using the wrench provided (9), see Section 6.4,...
-
Page 28: Incidents And Troubleshooting
Steady red and flashing (light) blue • Fault detected with ActivSecurity threshold low: user in contact with hook and/or not detected on pad 7.2. SUMMARY OF BATTERY LED CODES ON PRUNING SHEARS C45 Fault codes Usage Flashing with loss of tool power •... -
Page 29: Transport / Storage
Store the battery (refer to the battery operating instructions). Note In the OFF-SEASON, you may have your pruning shears serviced by an authorised repairer. For more infor- mation, consult an authorised distributor or contact PELLENC. 9. ACCESSORIES AND CONSUMABLES 9.1. ACCESSORIES... -
Page 30: Consumables
PRUNING SHEARS C45 163529-A Name Reference Illustration Arm band 120989 Holster to be fitted on the adjustable belt 152336 Adjustable belt 154772 Grease nipple 158783 13 mm angled wrench 9.2. CONSUMABLES Name Reference C45 blade kit 165510 C45 maintenance kit... -
Page 31: Warranties
The warranty is fully integral to the product sold by PELLENC. 10.1.2.1.2. SPARE PARTS The commercial warranty also covers original PELLENCspare parts, excluding labour and to the exclusion of certain... -
Page 32: Paid After-Sales Service
PELLENC Products are guaranteed under the commercial warranty as from delivery to the customer for a period of two (2) years for products connected to a PELLENC battery, and for a period of one (1) year for other PELLENC products. -
Page 33: Specific Warranties
Paid after-sales service also covers original PELLENC spare parts, excluding labour and outside the legal and commercial warranty period. In case of replacement of original PELLENC spare parts in the context of after-sales service, said latter are covered by a warranty of one year as from the installation date. -
Page 34: Statements Of Compliance
PRUNING SHEARS C45 163529-A 11. STATEMENTS OF COMPLIANCE 11.1. STATEMENT OF COMPLIANCE: C45 MANUFACTURER / ENTITY AUTHORIZED TO COMPILE PELLENC THE TECHNICAL FILE ADDRESS Quartier Notre-Dame - 84120 Pertuis (France) We hereby declare that the machine referred to below as:... -
Page 35: Declaration Of Conformity : C45
PRUNING SHEARS C45 163529-A 11.2. UK DECLARATION OF CONFORMITY : C45 MANUFACTURER / ENTITY AUTHORIZED TO COMPILE THE PELLENC TECHNICAL FILE ADDRESS Quartier Notre-Dame - 84120 Pertuis (France) We hereby declare that the machine referred to below as: GENERIC DENOMINATION... - Page 40 PELLENC Quartier Notre Dame - 84120 Pertuis (France)
Need help?
Do you have a question about the C45 and is the answer not in the manual?
Questions and answers