Table of Contents
Advertisement
Available languages
Available languages
16 • ENGLISH
9
User manual
10
HEPA filter
11
HEPA filter cover
12
Sponge filter
DRUM ASSEMBLY
Warning! If any part is missing or damaged, please do not
assemble until you have all the parts.
Invert drum to install wheel
Insert the four wheels (7) into the socket of wheel base.
Be sure that wheels spin freely (Fig. B)
ASSEMBLING THE UNIT
1. Put the HEPA filter (10) into float holder, then lid the
HEPA filter cover (11), fasten it clockwise. On the
contrary, remove the HEPA filter anticlockwise (Fig. C).
NOTE: When picking up small amounts of liquid the HEPA
filter can be left in place. When picking up large amounts
of liquid we recommend that the HEPA filter should be
removed. If the HEPA filter is not removed, it will become
saturated and misting may appear in the exhaust.
2. Fitting the dust bag. Put the dust bag board (8) into inlet
base. (Dust bag board should be aim at the slot of the inlet
base). Rotate the board clockwise 90º degrees to fasten
the dust bag according to arrow direction (LOCK side)
(Fig. D).
To remove the dust bag from the inlet base, just rotate
the dust bag board anticlockwise 90º degree (OPEN side),
then take out the dust bag.
NOTE: The dust bag use only for dry-vacuum.
3. Install the power head assembly into the drum assembly
as shown (Fig. E).
4. Rotate both latches down and press until you hear them
snap over the flanges on the drum (Fig. F).
5. Insert the flexile hose connector into the inlet base of the
vacuum cleaner (Fig. G).
OPERATION
Accessories use instructions
The vacuum cleaner is equipped with three nozzles for different
applications. Each individual nozzle can either be fitted onto the
connecting tube or directly onto the handle of the flexible hose.
1. Floor brush
This is suitable for cleaning wide areas. The floor brush is
fitted with a practical 360º tie-in, this ensures that you can
reach easily into any corner (Fig. H).
2. Sofa brush
1
You can use this to clean the dust from books or sensitive
1
objects such as picture frames etc. This nozzle is suitable
for the careful cleaning of upholstered furniture, mattresses,
1
cushions, curtains etc. (Fig. I)
1
3. Crevice nozzle
This nozzle is suitable for sucking and cleaning the corners or
niches that cannot be reached with the floor brush. Besides, it
can be used as blowing tool (Fig. J).
ATTENTION!
1. Make sure all the assembly is according to the instructions.
Connect the hose to the unit, then install the specific
accessories for the intended cleaning purpose. Insert the
plug into the socket. Press the ON/OFF switch button, start
the using. After using, press the ON/OFF switch button to
stop. Unplug the cord from the socket. (Fig. K)
WET VACUUMING
Caution! Always remove the dust bag when you commencing
wet vacuuming.
1. When picking up small amounts of liquid the HEPA filter
may be left in place.
2. When picking up large amounts of liquid we recommend
that the HEPA filter should be removed. If the HEPA filter
is not removed, it will become saturated and misting may
appear in the exhaust.
3. When the liquid in the drum reaches a predetermined
level, the float mechanism will rise automatically to cut off
air-flow, the indicator light turn on at the same time. When
this happens, turn off the vac, unplug the power cord, and
empty the drum.
4. After using the vac to pick up liquids, the HEPA filter must
be cleaned and dried to reduce the risk of possible mildew
and damage to the filter.
5. The sponge filter should be cleaned and dried if necessary,
the removal method is shown in (Fig. L).
6. When the drum full, turn anticlockwise the water lid and
empty the water (Fig. M).
DRY VACUUMING
Caution! Never dry-vacuum without the filter assembly
installed.
1. For dry –vacuum using, there are two fitting methods:
a.
Dust bag;
b. HEPA filter. For mass dust cleaning, we advise
to use dust bag. For a bit but tiny dust cleaning,
we advise to use HEPA filter. Since the HEPA filter
have better fitting performance but will low down
the air flow.
2. The device has dirt full and block indication function,
the light turns on that means the air route way is blocked.
In this case, user should switch off the device and check:
a.
Is the hose or accessories blocked by large dirt?
b. Is the filter blocked by dirt?
Advertisement
Table of Contents
