PDK Red 1 Quick Start Manual

1. Package Contents
Key lock (1)
Red 1
One Door Controller (1) Battery Leads (1)
Labels (2) Enclosure Screws (2)
4. Input A / DPS Connection
+ -
BUS
ACTIVITY
+ -
-
0 1 L A B NC C NO
12-24VDC
BAT
B
A
+ -
DPS Contact
Double DPS
Contact
A
DPS (Door Position Switch)
- The DPS is mounted on the door frame in the
desired location with a 22/2 wire running from the DPS to the controller.
Wire the DPS to the controller as shown above. When using two DPS
sensors for double doors you will wire them in series with only two conduc-
tors running back to the controller for connection.
B AUX Input
- A rule can be setup to trigger events or outputs based on this
input trigger.
Diode (1)
Jumpers (2)
Mount
OSDP
POWER
HEART
LINK
RELAY
ETHERNET
+ -
BUS
A
ACTIVITY
0 1 L -
A B NC C NO
12-24VDC
Maglock
BAT
A
Maglock
- When installing a Maglock it is typical to install a REX (Request to
Exit) at the door for free egress. Run an 18/2 wire from the Maglock to the
Door Controller, connecting to the Maglock as shown.
B
REX (Request to Exit)
18/5 wire ran from the REX to the controller. Wire the REX to the controller
and maglock as shown above. If reporting is not needed in the system ,
simply eliminate the green labeled wire.
C
Jumper Block
If jumper is off, the relay is a standard dry contact needing input into
AUX Input
- A rule can be setup to trigger events or outputs based on this
input trigger.
2. Mounting Controller
POE OUT
POE IN
OSDP
POWER
HEART
LINK
RELAY
ETHERNET
-
+ BUS
ACTIVITY
+ -
0 1 L A B - NC C NO
12-24VDC
BAT
-
Mount the Red 1 enclosure securely to a wall.
5. Input B / REX Connection
+
BUS
C
+ -
BUS
ACTIVITY
+ -
-
0 1 L A B NC C NO
12-24VDC
BAT
If using a powered REX,
run to any 12VDC
output on controller.
B
REX
- The REX is mounted in the desired location with an
- Use to designate (+) or (-) board voltage out of NO and NC.
3. Reader Connection
Red 1 Controller
A
Reader
+ -
+ -
A
Reader - The reader is mounted at the door with a 22/5 or 22/6 wire ran to
the door controller. Wire the reader to the controller as shown above. Be
sure to check polarity and voltage prior to powering controller.
B
OSDP - Place jumper to enable OSDP (see OSDP reference guide at the end
of this guide for more info)
6. Locking Relay
-
A
A
Diode - The provided diode must be installed when using a strike. Install at
the strike with the grey stripe of diode on positive and the black on nega-
tive.
B
NC - Used for maglocks (or strikes in fail-safe configuration). Connect the
negative (-) of the maglock or strike to NC on the door controller.
C NO
- Used for strikes in fail-secure configuration. Connect the negative (-) of
the strike to NO on the door controller.
D
Jumper Block - Use to designate (+) or (-) board voltage out of NO and NC.
If jumper is off, the relay is a standard dry contact needing input into
OSDP
POWER
HEART
LINK
OSDP
RELAY
POWER
B
HEART
ETHERNET
LINK
RELAY OSDP
+ -
BUS
ACTIVITY
ETHERNET
-
0 1 L A B NC C NO -
+ BUS
12-24VDC
ACTIVITY
BAT
-
0 1 L + -
A B NC C NO
0 1 L 12-24VDC
BAT
OSDP
Wiring
RELAY D
ETHERNET
+ -
BUS
ACTIVITY
+ - -
0 1 L A B NC C NO
12-24VDC
BAT
B C
OR
-
+
BUS