Nautilus EV9.16 Owner's Manual page 18

C H A N G I N G T H E G A M E I N H E A LT H A N D F I T N E S S
CONSOLE CODES
Machine Status Codes
You can view maintenance information such as the
run time in hours, number of workouts and distance,
as well a machine type and software revision.
To view the status of your machine:
1. Press [Level: UP], [4], [ENTER]. The console
will display "MACHINE STATUS"
2. Press [Level: UP] or [Level: DOWN] to scan
through the choices. Select the option you want
to view by pressing [ENTER]. Press [CLEAR] to
exit the machine status codes.
The machine status options are as follows:
Machine run time in hours—Display the machine
run time in hours. The console will display "RUN
HOURS #####".
Number of workouts—Display the number of times
a workout key has been pressed. The console will
display "WORKOUTS ####".
Distance traveled—Display the total distance
traveled in miles (or km if console is set to Metric
units) . The console will display "DISTANCE
#####".
Software revision—Display the console software
revision number. The console will display "CONS
41375-###".
Machine type—Display the machine type the
console is currently configured to. The console will
display "ELLIPTICAL" or other machine type.
Machine run time in hours since last cleared—
(used for maintenance) Display the machine run
time since last cleared. The console will display
"MAINT HOURS #####". This will provide the
32
™
number of hours between service or maintenance
calls. The machine run time is reset to zero in the
following Diagnostics section.
3. To exit "MACHINE STATUS", press the
[CLEAR] key.
Diagnostic Codes
Diagnostic codes are used to test various components
of the machine such as the display, keyboard, serial
port, alternator, and tachometer, as well as viewing
the error log information and resetting the time
between service or maintenance calls.
To run diagnostics and view diagnostic
information:
1. Press [Level: UP], [6], [ENTER]. The console
will display "DIAGNOSTICS"
2. Press [Level: UP] or [Level: DOWN] to scan
through the choices. Select the option you want
to view by pressing [ENTER].
The diagnostic options are as follows:
Test display—To test the LCD display, press
[ENTER] when the message, "DISPLAY TEST" is
displayed. The console screen alternates turning
on all LCD segments and a representative program
screen. Verify that all LCD segments turn on.
Test keyboard—To test all the keys on the
keyboard, press [ENTER] when the message, "KEY
TEST" is displayed. Then, press any key on the
keyboard and that key's name will be displayed in
the text line. Press [CLEAR] as the last key to exit
this test.
CONSOLE CODES
Test serial port—To test the serial port, press
[ENTER] when the message, "SERIAL TESTS" is
displayed. This test performs a serial loop back
test. Select the CSAFE RS-232 selection. You
will need a loop-back test cable (PN 040051-001)
inserted into the appropriate connector port to
successfully run this test. Console will display
either "PASS" or "FAIL".
Test alternator—To test the machine's alternator,
press [ENTER] when the message, "ALT TEST" is
displayed. This test verifies the alternator field
routines through the console. Position yourself
on the machine and press [LEVEL: UP] for "field
on". After exercising briefly you should build up
resistance. For "field off", press [LEVEL: DWN].
Test tach response—To test the machine's
tachometer, press [ENTER] when the message,
"TACH TEST" is displayed. Start exercising on
the machine. The console should regulate the
alternator resistance based on the tach signal to
maintain approximately 2,000 RPMs while you are
exercising. If not, there is a possible problem in
the AC tap or field circuit. Check the alternator, the
AC tap wire, the field wire, the diode, the terminal
posts, and the main cable.
3. To exit "DIAGNOSTICS", press the [CLEAR] key.
To review the error log and reset the
service timer,
1. Press [Level: UP], [7], [ENTER]. The console
will display "DIAGNOSTICS2". Press [Level:
UP] or [Level: DOWN] to scan through the
choices. Select the option you want by pressing
[ENTER].
Error log —To display the machine's error log,
press [ENTER] when the message, "ERROR LOG",
is displayed. The console will report various
error messages in the display window. The total
amount of errors will be displayed in the upper
right window. Note that only the highest priority
reported error will be displayed. Errors are handled
in two ways. First, as a non-fatal "WARNING"
which will display the text message but continue
system operation until you press the [CLEAR] key.
The second way is a fatal "ERROR" which will
stop the exercise and return the system to an idle
intensity state. The console will display the error
text and not let you restart the program unless
power has been turned off and then back on.
Reset service time —To reset the time between
service or maintenance calls, press [ENTER]
when the message, "MAINT HOURS" is displayed.
Selecting this code will reset the maintenance
timer to 0 hours.
2. To exit "DIAGNOSTICS2", press the
[CLEAR] key.
Configuration Codes
You can change the machine type to from/to Stepper,
StepMill, Bike or Elliptical:
To change the machine type:
1. Press [LEVEL: UP], [8], [0]. Press [Level: UP]
or [Level: DOWN] to scan through the choices.
Select the machine type you want by pressing
[ENTER].
2. Press the [CLEAR] key to exit configuration.
33