Advertisement
Quick Links
ASSEMBLY AND INSTALLATION
T0627
WARNING:
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
Hardware Package (included):
Mounting Screw X2
Mounting Screw X2
#6/32 X1/2 in
#8/32X1/2 in
Tools Needed:
(1) Philip-head Screwdriver
Important to Know:
1. If you are not familiar with state and local electrical
codes, it is recommended that you consult with a
qualified electrician.
2. This fixture requires a 120 VAC, 60 Hz power
source.
3. For general safety and to avoid any possible
damage to the sensor, be sure the power is
switched "off" before adjustment.
Maximum Wattage: 22 W
Working Temperature Range:
Note: Fixture can be wall mounted or eave mounted.
FRONT
Outlet Box
Mounting Strap
INSTRUCTIONS
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
Mounting Screw X2
#10/24 X1/4 in
(2) 1/8" wide Flat-head Screwdriver
-13°F ~ 113°F
Wall Mounted
L GND N
L GND N
Mounting Strap
1. Phillips-head screwdriver for attaching mounting screws to
mounting strap, mounting bracket and fixture to mounting bracket.
2. 1/8" wide flat-head screwdriver for connecting the source wires
into the wiring terminal station on the mounting bracket.
Features:
1. Energy saving LED fixture.
2. Capable to function as a standalone wall switch light or
as part of a Link Group.
3. When connected to a Link Group, light will receive
signal to turn ON at full brightness automatically when
motion sensor signal is detected and then DIMS light to
low level brightness automatically when motion stops.
4. When connected to a Link Group, light will receive
signal to remain OFF daylight hours and automatically
turns the light ON during evening hours.
5. The wall switch that the light is connected to can be
used to manually override and change functionality
and settings of certain modes.
Eave Mounted
Backplate
Page 1 / 4
Decorative cover
Fixture Mounting Screw
Light Fixture
Sensor
220209
Decorative cover
Advertisement
Related Manuals for Vaxcel Lambda T0627
Summary of Contents for Vaxcel Lambda T0627
- Page 1 ASSEMBLY AND INSTALLATION INSTRUCTIONS T0627 WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS. Hardware Package (included): Mounting Screw X2 Mounting Screw X2...
- Page 2 Installation Steps Turn off the power at fuse or circuit box. 1. The fixture mounting bracket is pre-assembled on the light fixture. Unscrew both the decorative cover and the fixture mounting screw in order to remove the mounting bracket. 2. Install the mounting strap to the outlet box with the stamped word “FRONT” facing away from the outlet box, using two mounting screws that best fit the outlet box.
- Page 3 RF Linking Network Setup ● From all the light units you would like to link, select one as the main unit and the others as sub-units. ● First, setup all of the sub-units by pressing the Link button two times within 3 seconds. The sub-units will flash once every 1 second (meaning they are waiting to receive a linking signal from the main light).
- Page 4 5-YEAR LIMITED WARRANTY: All products are warranted to be free of defects in material and workmanship for five (5) years from date of purchase. This warranty is limited to the correction of any such defect, or the replacement of any such defective item(s), provided that: (a) we are properly notified and consent to return of the item(s) in question:(b) the item(s) is / are returned with proof of purchase date;...