Detergent And Rinse Aid - Haier DW12-EBM 1S Manual

Salt
Salt
The hardness of the water varies from place to place. If hard
water is used in the dishwasher, deposits will form on the dishes
and utensils.
The appliance is equipped with a special softener that uses a salt
specifically designed to eliminate lime and minerals from the water.
Loading the Salt into the Softener
Always use salt intended for use with dishwashers. The salt con-
tainer is located beneath the lower rack and should be filled as
follows:
- Remove the lower rack and then unscrew and remove the cap
from the salt container;
- If you are filling the container for the first time, fill it with water;
- Place the end of the funnel (supplied) into the hole and intro
duce about 2 kg of salt. It is normal for a small amount of water
to come out of the salt container.
- Carefully screw the cap back on.
To prevent the formation of rust, load the salt just before begin-
ning a wash cycle.
Adjusting Salt Consumption
The dishwasher is designed to allow for adjusting the amount of
salt consumed according to the hardness of the water used. This
is intended to optimise and customise the level of salt consump-
tion so that it remains at a minimum.
To adjust salt consumption, proceed as follows:
- Unscrew the cap from the salt container;
- On the neck of the container there is a ring with an arrow on it
(see figure above). If necessary, turn the ring anti-clockwise
from the "-" sign towards the "+" setting, according to water
hardness.
- It is highly recommended that the following table be consulted
when making adjustments.
Water Hardness
Salt
Clarke
Selector
dH c o n s u m p t i o n
mmol/l
degrees
position
(Grams/cycle)
0 17 0 1,7
0 14 / 0
18 44 20
14 36 1,8 4,4 "-"
45 89 4,5 8,9 MED 40
36 71
"+" 60
>89 >8,9
>71
.3. .3. .3.
.3. .3.

Detergent and Rinse Aid

Detergent
Detergent specifically intended for use with dishwashers must
be used. The dispenser must be refilled before the start of each
wash cycle following the instructions provided in the "Wash Cycle
Table ". The detergent dispenser is located on the inside panel
of the door.
Loading the detergent
To open cover "A" on the dispenser, press button "B". The de-
tergent for the wash cycle should be poured into compartment
"C".
After the detergent has been placed in the dispenser, close the
cover and press down until it clicks in place.
B B B B B
C C C C C A A A A A
Notice: To facilitate closing the cover, remove any excess
Autonomy
detergent on the edges of the dispenser.
(cycles/2kg)
/
60
40
25
GB GB GB GB GB GB GB GB GB GB
Rinse Aid
This product makes dishes sparkle and helps them to dry
without spotting. The dispenser is located on the inside
panel of the door and should be filled after every 80 wash
cycles.
Loading the Rinse Aid
To open the dispenser, turn cap "C" anticlockwise and then
add the rinse aid, making sure not to overfill.
The amount of rinse aid used for each cycle can be regu-
lated by turning dose adjuster "F", located beneath cap
"C", with a screwdriver. There are 6 different settings; the
normal dosage setting is 3.
Important:
Proper dosage of the rinse aid improves drying.
If drops of water remain on the dishes or spotting occurs,
the dosage adjuster should be turned to a higher setting. If
the dishes have white streaks, turn the dosage adjuster to
a lower setting.
C C C C C
F F F F F
.4. .4. .4. .4. .4.