Cleaning And Special Maintenance; Installation; Troubleshooting - Haier DW12-EBM 1S Manual

Haier dw12-ebm 1s: user guide

Hide thumbs Also See for DW12-EBM 1S:

Owner's manual (8 pages)

Table Of Contents

Table of Contents

Available languages

Enlarged version

Cleaning and Special Maintenance

Filter Assembly

For best performance and results, the filter assembly must be

cleaned.

The filter efficiently removes food particles from the wash water,

allowing it to be recirculated during the cycle. For this reason, it

is advisable to remove the larger food particles trapped in the

filter after each wash cycle by rinsing the semi-circular filter and

cup (A) under running water. To remove the filter assembly, pull

on the cup handle in the upward direction. The entire filter as-

sembly (made up of the semicircular filter (A) and the fine filter

(B)) should be cleaned at least once a month. To clean the filter

and fine filter, use a cleaning brush. Then, reassemble the filter

parts as shown in the figures below and refit the entire assembly

in the dishwasher, positioning it in its seat and pressing downward.

The dishwasher must never be used without the filters. Improper

replacement of the filters may reduce the performance of the

appliance and damage dishes and utensils.

Troubleshooting

It may occur that the dishwasher does not function or does not

function properly. Before calling for assistance, see what can be

done first: have you forgotten to press one of the buttons or to

perform an essential operation?

The Dishwasher Does Not Start

Have you checked whether:

- the plug is pushed into the socket correctly;

- the power is on in the house;

- the door is closed properly;

- the ON-OFF switch is on "ON";

- the water supply is turned on.

The Dishwasher Does Not Load Water

Have you checked whether:

- the water is turned on and the hose is connected properly;

- the water supply to the house is on and has sufficient pressure;

- the water supply hose is crimped or bent;

- the filter for the water supply hose is clogged.

The Dishes Are Not Clean

Have you checked whether:

- the water is turned on and the hose is connected properly;

Cleaning the Spray Arms

It may happen that food particles become encrusted on the

sprayer arms and block the hole (see "Close up view [interior]",

letters C-F). Check the sprayer arms periodically and clean them

when needed.

- the water supply to the house is on and has sufficient pressure;

- the water supply hose is crimped or bent;

- the filter for the water supply hose is clogged.

The Dishwasher Does Not Drain

Have you checked whether:

- the drain hose is crimped or bent.

Lime Deposits or a White Film Form on the Dishes

Have you checked whether:

- the lid of the salt container is closed properly;

- the rinse aid dosage is correct.

If, despite all these checks, the dishwasher still does not function

and/or the problem persists, contact the nearest authorised ser-

vice centre and provide the following information:

- the nature of the problem;

- the model type number (Mod...) and the serial number (S/N...),

which are indicated on the plate located on the side of the inner

part of the door.

Never call unauthorised technicians and refuse to allow parts

to be installed that are not original spare parts.

.9.

Installation

Positioning the Appliance

Position the appliance in the desired location. The back should

rest against the wall, and the sides along the adjacent cabinets

or wall. The dishwasher is equipped with water supply and drain

hoses that can be positioned to the right or left to facilitate proper

installation.

Levelling the Appliance

Once the appliance is positioned, adjust the feet (screwing them

in or out) of the dishwasher until it is level. In any case, the appli-

ance should not be inclined more than 2 . If the appliance is level,

it will help ensure proper performance.

Cold Water Connection

Connect the cold water supply hose to a threaded 3/4 (gas) con-

nector and make sure that it is fastened tightly in place (see fig.

1).

If the water pipes are new or have not been used for a prolonged

period of time, let the water run to make sure that the water is

clear and free of impurities. If this precaution is not taken, there is

a risk that the water inlet can get blocked and damage the

appliance.

Hot Water Connection

The water supply to the appliance can also be connected to the

house's hot water line (centralised system, heating system), as

long as it does not exceed a temperature of 60 C.

In this case, the wash cycle time will be shortened by about 15

minutes and the wash efficiency slightly reduced.

The connection must be made to the hot water line following the

same procedures as for the connection to the cold water line.

Warning

The appliance is to be connected to the water mains

using new hose-sets and that old hose-sets should

not be reused.

Drain Hose Connection

Insert the drain hose into a drain pipe with a minimum diameter

of 4cm, or let it run into the sink, making sure to avoid bending

or crimping it. Use the special plastic support that comes with

the appliance (see fig .2). The free end of the hose must be at a

height between 40 and 100 cm and must not be immersed in

water.

Attention:

The special plastic hose support must be solidly fastened to

the wall to prevent the drain hose from moving and allowing

water to spill outside the drain.

Electrical Connection

After making sure that the voltage and frequency values for the

current in the home correspond to those on the rating plate

(located on the stainless steel inner door of the appliance) and

that the electrical system is sized for the maximum voltage on

the rating plate, insert the plug into an electrical socket which is

earthed properly (the earthing of the appliance is a safety re-

quirement mandated by law).

If the electrical socket to which the appliance must be connected

is not appropriate for the plug, replace the plug rather than using

adaptors or the like as they could cause overheating and burns.

The symbol

ing indicates that this product may not be treated

as household waste. Instead it shall be handed over

to the applicable collection point for the recycling

of electrical and electronic equipment. By ensuring

this product is disposed of correctly, you will help

fig.1

prevent potential negative consequences for the

environment and human health, which could other-

wise be caused by inappropriate waste handling of

this product.

For more detailed information about recycling of this

product, please contact your local city office, your

household waste disposal service or the shop where

you purchased the product.

.10.

fig.2

on the product or on its packag-

Table of Contents

Cleaning And Special Maintenance; Installation; Troubleshooting - Haier DW12-EBM 1S Manual

Available languages

Cleaning and Special Maintenance

Troubleshooting

Installation

Related Manuals for Haier DW12-EBM 1S

Related Content for Haier DW12-EBM 1S

Table of Contents