SPIT BS10 Safety And Operating Manual page 10

10
Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
Do not open the battery. Danger of short-circuiting.
Protect the battery against heat, e. g.,
against continuous intense sunlight, fire,
water, and moisture. Danger of explosion. In
case of damage and improper use of the battery, vapours
may be emitted. Ventilate the area and seek medical help
in case of complaints. The vapours can irritate the
respiratory system.
Use the battery only in conjunction with your
tool. This measure alone protects the battery against
dangerous overload.
Spit
Use only original batteries with the voltage listed on
the nameplate of your power tool. When using other
batteries, e.g. imitations, reconditioned batteries or other
brands, there is danger of injury as well as property damage
through exploding batteries.
Product Description and Specifications
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious
injury. While reading the operating instructions,
unfold the graphics page for the machine and
leave it open.
Intended Use
The machine is intended for driving in and loosening screws as
well as for drilling in wood, metal, ceramic and plastic. The
light of this power tool is intended to illuminate the power
tool's direct area of working operation and is not suitable for
household room illumination
Product Features
The numbering of the product features refers to the illustration
of the machine on the graphics page.
1 Keyless chuck
2 Torque presetting ring
3 Gear selector
4 Battery unlocking button*
5 Battery pack*
6 Rotational direction switch
7 On/Off switch
8 Handle (insulated gripping surface)
9 "PowerLight"
10 Screwdriver bit*
11 Universal bit holder*
*Accessories shown or described are not part of the standard delivery
scope of the product. A complete overview of accessories
can be found in our accessories program.
Cordless Drill/DriverRated voltage
No-load speed
– 1st gear
– 2nd gear
Max. torque for hard/soft screwdriving
application according to ISO 5393
Max. drilling dia.
– Steel
– Wood
Max. screw dia
Chuck clamping range
Weight according to EPTA-Procedure
01/2003
*dependent of the battery pack being used
Technical Data
Noise/Vibration Information
Measured sound values determined according to EN 60745.
Typically the A-weighted sound pressure level of the product is
73 dB(A). Uncertainty K=3 dB. The noise level when working can
exceed 80 dB(A).
Wear hearing protection!
Vibration total values a
determined according to EN 60745: Drilling into metal:
a <2.5m/s
h
The vibration emission level given in this information sheet has
been measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with another.It
may be used for a preliminary assessment of exposure. The
declared
Spit applications of the tool. However if the tool is used for different
power
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly
increase the exposure level over the total working period. An
estimation of the level of exposure to vibration should also take
into account the times when the tool is switched off or when it
is running but not actually doing the job. This may significantly
reduce the exposure level over the total working period. Identify
additional safety measures to protect the operator from the
effects of vibration such as: maintain the tool and the
accessories, keep hands warm, organise work patterns.
Assembly
Battery Charging (see figure A)
Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the
lithium ion battery of your power tool.
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium ion battery can be charged at any time without
reducing its service life. Interrupting the charging procedure
does not damage the battery. The Lithium-Ion battery is
protected against deep discharging by the "Electronic Cell
Protection (ECP)". When the battery is empty, the machine is
switched off by means of a protective circuit: The inserted tool
no longer rotates.
Do not continue to press the On/Off switch after the
machine has been automatically switched off. The battery
can be damaged.
To remove the battery 5 press the unlocking buttons 4 and pull
out the battery downwards. Do not exert any force. The
battery is equipped with a NTC temperature control which
allows charging only within a temperature range of between 0
°C and 45 °C. A long battery service life is achieved in this
manner.
Observe the notes for disposal.
Changing the Tool (see figure B)
Before
maintenance, tool change, etc.) as well as during
transport and storage, remove the battery from the
power tool. There is danger of injury when unintentionally
actuating the On/Off switch.
The drill spindle is locked when the On/Off switch 7 is not
V= 10.8
pressed. This makes quick, convenient and easy changing of the
tool in the drill chuck possible. Open the keyless chuck 1 by
min 0 –350
-1
turning in rotation direction, until the tool can be inserted.
min 0 – 1300
-1
Insert the tool.
Nm 30/15*
Firmly tighten the collar of the keyless chuck 1 by hand in
rotation direction.
Dust/Chip Extraction
mm 10
Dusts from materials such as lead-containing coatings, some
mm 19
wood types, minerals and metal can be harmful to one's
mm 7
health. Touching or breathing-in the dusts can cause allergic
mm 24/14
reactions and/or lead to respiratory infections of the user or
bystanders. Certain dusts, such as oak or beech dust, are
kg 1.0
considered as carcinogenic, especially in connection with
wood-treatment additives (chromate, wood preservative).
Materials containing asbestos may only be worked by
specialists.
Prevent dust accumulation at the workplace. Dusts can
easily ignite.
(triax vector sum) and uncertainty K
h
, K =1.5 m/s , Screwdriving: a
2 2
vibration emission level
any work on the
−
Provide for good ventilation of the working place.
−
It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
English
<2.5m/s , K =1.5m/s .
h 2 2
represents the main
machine itself (e. g.