Table of Contents
  • Français

    • Machine Data Label
      • Table of Contents
    • How to Use this Manual
    • Safety
    • Important Safety Instructions
    • Consignes de Sécurité Importantes
    • Hazard Intensity Level
    • Degrés de Risques en cas de Danger
    • Safety Labels
    • Grounding Instructions - 120V
    • Operations
    • Technical Specifications
    • Handle Installation
    • Handle Height Adjustment
    • Controls
    • Machine Operation
    • Maintenance
    • Pad Installation
    • Machine Troubleshooting
    • Service Schedule
    • Suggested Spare Parts

Advertisement

Quick Links

Floor Burnisher
1500 Series
Operating Instructions (ENG)
MODELS:
BDP 51/1500 C 115V
1.009-098.0
BDP 51/1500 C
1.009-101.0
86387270-C
07/02/18

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 1500 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Kärcher 1500 Series

  • Page 1 Floor Burnisher 1500 Series Operating Instructions (ENG) MODELS: BDP 51/1500 C 115V 1.009-098.0 BDP 51/1500 C 1.009-101.0 86387270-C 07/02/18...
  • Page 2: Machine Data Label

    Thank you for choosing our product. Warranty registration is quick and easy. Your registration will allow us to serve you better over the lifetime of the product. To register your product go to: http://warranty.karcherna.com/warrantyregistration.aspx 86387270 Operator’s Manual - Floor Burnisher (1500 Series)
  • Page 3: Table Of Contents

    Service Schedule ......16 Suggested Spare Parts....17 86387270 Operator’s Manual - Floor Burnisher (1500 Series)
  • Page 4: How To Use This Manual

    NOTE: The manual part number is located on the Address: lower right corner of the front cover. Phone Number: Sales Representative: The model and serial number of your machine are located on the back of the machine. 86387270 Operator’s Manual - Floor Burnisher (1500 Series)
  • Page 5: Safety

    This appliance has been designed for use with pads specified by the manufacturer. The fitting of other pads may affect its safety. This machine is for dry use only and shall not be used or stored outdoors in wet conditions. READ AND SAVE THESE INSTRUCTIONS 86387270 Operator’s Manual - Floor Burnisher (1500 Series)
  • Page 6: Consignes De Sécurité Importantes

    Cette machine est faite pour un usage à sec seulement et ne doit pas être utilisée ou rangée à l'extérieur dans des conditions humides. LIRE ET CONSERVER CES INSTRUCTIONS 86387270 Operator’s Manual - Floor Burnisher (1500 Series)
  • Page 7: Hazard Intensity Level

    In Flammable or Explosive areas. In areas with possible falling objects WHEN SERVICING MACHINE: Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the machine. Use manufacturer approved replacement parts. 86387270 Operator’s Manual - Floor Burnisher (1500 Series)
  • Page 8: Degrés De Risques En Cas De Danger

    Éviter les parties amovibles. Ne pas porter de vêtements amples, tels que des vestes, des chemises ou des vêtements avec manches lors de l’utilisation de la machine. Utiliser les pièces détachées homo- loguées. 86387270 Operator’s Manual - Floor Burnisher (1500 Series)
  • Page 9: Safety Labels

    Emplacement De L'étiquette De Sécurité REMARQUE: Ces dessins indiquent l'emplacement des étiquettes de sécurité sur la machine. Si, à tout moment, les étiquettes deviennent illisibles, contactez votre représentant autorisé pour un remplacement rapide. 86387270 Operator’s Manual - Floor Burnisher (1500 Series)
  • Page 10: Grounding Instructions - 120V

    à la terre de votre prise murale. Ne modifiez pas la fiche fournie avec l'appareil: si elle ne correspond pas à la prise murale, faites installer une prise adéquate par un électricien qualifié. 86387270 Operator’s Manual - Floor Burnisher (1500 Series)
  • Page 11: Operations

    DIMENSIONS (L X W X H) 31” (80 cm) X 21” (54 cm) X 49” (124 cm) NOTE: Always use a pad, which has been designed for electric ultra high speed burnishing of at least 2000 rpm. 86387270 Operator’s Manual - Floor Burnisher (1500 Series)
  • Page 12: Handle Installation

    Tighten bolt and nut securely, then back off 1/4 to 1/2 turn. Fully tighten bolt and nut on rear of lower block on handle assembly. 4. Check handle for movement up and down. Plug motor cord into handle cord receptacle by routing the cords above the handle links. 86387270 Operator’s Manual - Floor Burnisher (1500 Series)
  • Page 13: Controls

    It should not be necessary to adjust the handle adjust bar unless the handle adjustment bar (1) the washer (3) and nut (2) have been disturbed. 86387270 Operator’s Manual - Floor Burnisher (1500 Series)
  • Page 14: Machine Operation

    Insure that handle is locked in position before starting machine. Assurez-vous que la poignée est bloquée en position avant de démarrer la machine. 4. Push the safety lock forward, unlocking the switch levers. 86387270 Operator’s Manual - Floor Burnisher (1500 Series)
  • Page 15: Machine Troubleshooting

    Damaged or unevenly worn pad on pad when not in use. Damaged pad driver Replace. Pad does not turn but motor is Belt is loose or broken Adjust or replace belt. running 86387270 Operator’s Manual - Floor Burnisher (1500 Series)
  • Page 16: Service Schedule

    Check pad wear to prevent buildup of chemicals Check pad driver system for damage Check handles, switches, and knobs for damage Store with pad off the floor Check all bearings for noise Check overall performance of machine 86387270 Operator’s Manual - Floor Burnisher (1500 Series)
  • Page 17: Suggested Spare Parts

    86224750 SPRING, COMP .48 OD X .91 L 86215130 BAR, HANDLE ADJ 86222560 PIN, PIVOT, HANDLE ADJ 86223550 ROD, HANDLE ADJ 86222480 PAD DRIVER, 20IN BURNISHER FLEX BELT, DRIVE 38 IN 86215330 86387270 Operator’s Manual - Floor Burnisher (1500 Series)
  • Page 18 Table of contents BDP 51/1500 C 115V (ALL MODELS) 20 CHASSIS 30 DRIVE / PAD LOCK 40 ELECTRICAL 50 HANDLE 60 MOTOR Valid on 03.10.2018 Page 1 / 12...
  • Page 19: Bdp 51/1500 C 115V (All Models)

    BDP 51/1500 C 115V (ALL MODELS) Description Quantity Unit CHASSIS 11.000 DRIVE / PAD LOCK 1.000 ELECTRICAL 1.000 HANDLE 1.000 MOTOR 1.000 Valid on 03.10.2018 Page 2 / 12...
  • Page 20 20 CHASSIS Valid on 03.10.2018 Page 3 / 12...
  • Page 21: Chassis

    20 CHASSIS Article no. Description Quantity Unit 8.638-718.0 CHASSIS .000 2.000 BRACKET, HANDLE LINK 8.621-546.0 8.613-664.0 SCREW, M8-1.25 X 20 HHMS ZNPLT 4.000 NUT, .51 PUSH SPRST 2.000 8.622-227.0 Wheel 5D X 1.25 X 13MMID GRY 4.000 8.622-602.0 WASHER, 14MMID X 36MMOD 8.000 8.622-572.0 WASHER, M8 FLT STL DIN125A ZNPLT...
  • Page 22: Drive / Pad Lock

    30 DRIVE / PAD LOCK Valid on 03.10.2018 Page 5 / 12...
  • Page 23 30 DRIVE / PAD LOCK Article no. Description Quantity Unit 8.621-494.0 AXLE, PAD DRIVER 1.000 8.621-751.0 COVER, BEARING 1.000 8.627-673.0 SCREW, M4 X 8 PPHMS 3.000 8.613-728.0 WASHER, M8 FLT STL DIN125A ZNPLT 10.000 8.622-328.0 PULLEY, .625 X 3.45 1.000 8.622-573.0 WASHER, M6 X 20.5 X 1.6 STL ZNPLT 1.000...
  • Page 24: Electrical

    40 ELECTRICAL Valid on 03.10.2018 Page 7 / 12...
  • Page 25 40 ELECTRICAL Article no. Description Quantity Unit 8.600-201.0 BOOT, 3/8 CIRCUIT BREAKER 1.000 8.619-845.0 CLAMP, 5/16 dia NYLON 1.000 8.636-910.0 CORD SET, STW, 14/75', YLW 1.000 8.621-692.0 CORDSET, 14/3 X 52", SJT, BLK 1.000 8.628-845.0 SCREW, M4.8 X 10 PHTF TYPEB 4.000 8.613-678.0 SCREW, M3.5 X 40 PHTF TYPEB...
  • Page 26: Handle

    50 HANDLE Valid on 03.10.2018 Page 9 / 12...
  • Page 27 50 HANDLE Article no. Description Quantity Unit 8.621-513.0 BAR, HANDLE ADJUST 1.000 8.636-601.0 BUMPER, FLOOR MACHINE 1.000 8.600-407.0 GRIP, POLISHER HANDLE 2.000 8.638-552.0 ASM, SLIDER TUBE 1.000 8.600-515.0 Lock safety handle 1.000 8.600-516.0 Lever switch 2.000 8.613-635.0 NUT, M6 HEX 4.000 8.613-636.0 NUT, M10X1.5 HEX NYLOCK STL ZNPLT...
  • Page 28: Motor

    60 MOTOR Valid on 03.10.2018 Page 11 / 12...
  • Page 29 60 MOTOR Article no. Description Quantity Unit 8.600-692.0 SCREW, 3/8-16 X .75 HHCS STL GR5 ZNPLT 4.000 8.601-072.0 WASHER, M10 FNDR STL ZNPLT 4.000 8.638-429.0 MOTOR, LB1500 1.000 8.638-846.0 COVER ASM, LB2000 MOTOR 1.000 8.642-363.0 SCREW, 10-32 X .75 HEXFLHMS STL ZNPLT 3.000 8.638-828.0 KIT, BRUSH, MOTOR DS...

This manual is also suitable for:

Bdp 51/1500 c 115vBdp 51/1500 c

Table of Contents