Shutting Down; Maintenance And Care; Troubleshooting - Kärcher BC 14/12 Original Instructions Manual

Tighten the screw connection at the
container hole cone.
Install the bracket on the support tube to
ensure a more stable position of the in-
terior cleaner.
Connecting the hoses
Connect the high pressure pump to the
interior cleaner via a high pressure
hose.
Connect the water output stub to a re-
spective drain hose.
Note
The drain hose must have an inner diame-
ter of at least 17 mm. In order to prevent a
possible pressure reduction in the hose as
much as possible, narrowing in the hose or
sudden changes in direction must be avoid-
ed.
Cleaning
Connect the interior cleaner to the pow-
er supply and to an extension cable if
necessary.
Plug in the main plug.
Set the switch lever to the SPRAY posi-
tion. A cleaning will be performed at the
same time the excess water is suc-
tioned from the inside of the container.
Switch the interior on at the appliance
switch. The indicator lamp glows green.
Open the cleaning liquid supply.
Switch on the separate high pressure
pump.
Note
In order to ensure a thorough cleaning of
the container, we recommend performing
two cleaning cycles. The cycle lasts 36 sec-
onds each.
Set the switch lever to the SUCTION
position after the cleaning has been
concluded to suction off the remaining
water from the container.

Shutting down

Note
Flush/rinse the interior cleaner for 30 sec-
onds prior to shutting it off. This will avoid
crusting and adhesion and thus a prema-
ture wear of the seals.
Switch off the separate high pressure
pump.
Shut off the cleaning liquid supply.
Switch the interior off at the appliance
switch. Indicator lamp goes off.
Pull out the mains plug.
Remove the interior cleaner from the
container.

Maintenance and care

The basis for a safe operational plant is reg-
ular maintenance.
Use only original parts of the manufacturer
or part suggessted by him, such as
– replacement and wear parts
– Accessory parts
– Fuel
– Detergent
Danger
Risk of accident while working on the unit!
During all tasks:
Remove voltage from and secure high
pressure pump at the main switch.
Shut off the cleaning liquid supply.
Pull out the mains plug.
Who may perform maintenance?
Maintenance work may only be carried out
by persons who have been instructed in the
safe operation and maintenance on the
high-pressure systems.
Maintenance contract
In order to guarantee a reliable operation og
the equipment, we success, you signed a
maintenance agreement. Please refer to
you local Kärcher service department.
Maintenance schedule
Daily before use
Remove contamination in the gear area
on the cleaning head.
Monthly
Check screws for tight fit.

Troubleshooting

Troubleshooting notes
Danger
Risk of accident while working on the unit!
During all tasks:
Remove voltage from and secure high
pressure pump at the main switch.
Shut off the cleaning liquid supply.
Pull out the mains plug.
Note
The interior cleaner is intended exclusively
for use in a clockwise direction (seen from
the gear motor). If the power supply is re-
placed or if the electrical connections are
worked on, you must check whether the in-
terior cleaner is still turning into the proper
direction.
Who may remedy faults?
Operator
Work designated with the sign "Opera-
tor" may only be carried out by persons
who have been instructed in the safe
operation and maintenance on the high
pressure plant.
Electricians
Only persons with a professional train-
ing in the electro-technical area.
Customer Service
Work designated with the sign "Custom-
er Service" may only be done by the fit-
ters of Kärcher Customer Service.
Replacing the cleaning head
1 Axle stub
2 Slide ring gasket
3 Bevel wheel
4 Spray nozzle
5 Washer
Unscrew the axle stub and remove the
bevel wheel with seals and washer.
Coat the thread of the new axle stub
with sealant.
Insert the bevel wheel onto the axle stub
with seals and washer and screw in the
axle stub.
11
English