Tool Specifications; Ec Declaration Of Conformity; Noise/Vibration Information; Battery Charging - Würth EMS 18-A EC SL Translation Of The Original Operating Instructions

Tool Specifications

Cordless Multi Cutter
Art. No.
Rated voltage
No-load speed n
0
Oscillation angle, left/right
Weight according to
EPTA-Procedure 01:2014
Permitted ambient temperature
– during charging
1)
– during operation and during
storage
Recommended batteries
Recommended chargers
1) limited performance at temperatures <0 °C
Technical data determined with battery from delivery scope.

Noise/Vibration Information

Sound emission values determined according to
EN 60745-2-4.
Typically the A-weighted noise levels of the product are:
Sound pressure level 84 dB(A); Sound power level 95 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a
h
determined according to EN 60745-2-4:
2
Sanding: a =3.4 m/s , K=1.5 m/s
h
Sawing with plunge cut saw blade: a
Sawing with segment saw blade: a
2
Scraping: a =8.6 m/s , K=1.5 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main appli-
cations of the tool. However if the tool is used for different appli-
cations, with different accessories or insertion tools or is poorly
maintained, the vibration emission may differ. This may signifi-
cantly increase the exposure level over the total working
period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or when
it is running but not actually doing the job. This may significantly
reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from
the effects of vibration such as: maintain the tool and the acces-
sories, keep the hands warm, organisation of work patterns.
EMS 18-A EC SL
5700 511 X
V=
-1
min 8000–20000
°
kg
°C
°C
Akku-LI-CV 18V X,X Ah
AL XX -CV-LI
(triax vector sum) and uncertainty K
2
,
2
=8 m/s , K=1.5 m/s
h
2
=5.7 m/s , K=1.5 m/s
h
2
.
EC-Declaration of Conformity
We declare under our sole responsibility that the product
described under "Tool Specifications" complies with all
applicable provisions of the directives 2011/65/EU,
18.0
2014/30/EU, 2006/42/EC including their amendments
and is in conformity with the following standards:
1.4
EN 60745-1:2009+A11:2010,
EN 60745-2-4:2009+A11:2011,
2.1–2.4 EN 55014-1:2006+A1:2009+A2:2011,
EN 55014-2:1997+A1:2001+A2:2008,
EN 50581:2012.
0...+45
Technical file (2006/42/EC) at:
–20...+50
Adolf Würth GmbH & Co. KG, Abt. PPT,
Reinhold-Würth-Straße 12–17
74653 Künzelsau, Germany
Frank Wolpert
General Manager
Künzelsau: 01.06.2017
Note: The battery supplied is partially charged. To ensure
full capacity of the battery, completely charge the battery in
the battery charger before using your power tool for the first
time.
2
,
The lithium-ion battery can be charged at any time without
2
,
reducing its service life. Interrupting the charging procedure
does not damage the battery.

Removing the battery

The battery 4 is equipped with two locking levels that should
prevent the battery from falling out when pushing the battery
unlocking button 3 unintentionally. As long as the battery is
inserted in the power tool, it is held in position by means of a
spring.
To remove the battery 4, press the battery unlocking button 3
and pull the battery out of the power tool toward the rear.
Do not exert any force.
Dr.-Ing. Siegfried Beichter
General Manager

Battery Charging

16