Oven Care And Cleaning; Replacing The Oven Lamp; For The Installer - Haier HWO45NM6OXB1 User Instructions

Oven care and cleaning

Oven care and cleaning
H2O CAVITY CLEAN H2O CAVITY CLEAN
This function performs a cleaning cycle by in- This function performs a cleaning cycle by in-
jecting steam into the cavity for 15 minutes. jecting steam into the cavity for 15 minutes.
At the end of the cycle, any crusting that may At the end of the cycle, any crusting that may
have formed due to high-temperature cooking have formed due to high-temperature cooking
inside the oven cavity, will be softened and be- inside the oven cavity, will be softened and be-
come much easier to remove. come much easier to remove.
H20 CIRCUIT CLEAN H20 CIRCUIT CLEAN
This function performs a cleaning cycle of the This function performs a cleaning cycle of the
circuit, to keep it clean and efficient over time. circuit, to keep it clean and efficient over time.
WATER DISCHARGE WATER DISCHARGE
At the end of each steam cooking and after all At the end of each steam cooking and after all
the cleaning processes, it is recommended to the cleaning processes, it is recommended to
discharge residual water. discharge residual water.

Replacing the oven lamp

Replacing the oven lamp
IMPORTANT: The oven lamp must have pre- IMPORTANT: The oven lamp must have pre-
cise characteristics: cise characteristics:
• Structure suitable for high temperatures • Structure suitable for high temperatures
(up to 300 °C); (up to 300 °C);
• Power supply: see the V/Hz value on the se- • Power supply: see the V/Hz value on the se-
rial number plate; rial number plate;
• Power 25 W; • Power 25 W;
• Type G9 connector. • Type G9 connector.
ATTENTION: Make sure the appliance is off ATTENTION: Make sure the appliance is off
before replacing the lamp to avoid the possibil- before replacing the lamp to avoid the possibil-
ity of electric shock.
ity of electric shock.
• To avoid damage, spread a tea towel for • To avoid damage, spread a tea towel for
By pressing the On/Off button, before going to By pressing the On/Off button, before going to
stand by mode, follow the instructions on the stand by mode, follow the instructions on the
screen to proceed with the water discharge. screen to proceed with the water discharge.
1. Remove the tank until signed area 1. Remove the tank until signed area
2. Wait for discharge 2. Wait for discharge
3. Empty the tank 3. Empty the tank
pots and pans inside the oven; pots and pans inside the oven;
• Remove the screws holding the steel frame; • Remove the screws holding the steel frame;
• Remove the old lamp by sliding it out of its • Remove the old lamp by sliding it out of its
seat and taking care not to break it; seat and taking care not to break it;
• Insert the new bulb taking care not to touch • Insert the new bulb taking care not to touch
it with your hands (we recommend using a it with your hands (we recommend using a
disposable latex glove);
disposable latex glove);
• Replace the stainless steel frame taking • Replace the stainless steel frame taking
care not to pinch the silicone gasket seal; care not to pinch the silicone gasket seal;
• Screw in the stainless steel screws you pre- • Screw in the stainless steel screws you pre-
viously removed; viously removed;
• Connect the appliance to the power line.
• Connect the appliance to the power line.
EN 16 EN 16

For the installer

For the installer
INSTALL THE OVEN IN THE COUNTER INSTALL THE OVEN IN THE COUNTER
• The oven must be installed under a cook • The oven must be installed under a cook
top, in a column, or combined with the rel- top, in a column, or combined with the rel-
ative food-warmer drawer. ative food-warmer drawer.
• The dimensions of the space must be those • The dimensions of the space must be those
shown in figure. shown in figure.
• The cabinet material must be able to with- • The cabinet material must be able to with-
stand the heat. stand the heat.
• The oven must be centred within the walls • The oven must be centred within the walls
of the cabinet and fixed with the screws and of the cabinet and fixed with the screws and
bushings that are provided. bushings that are provided.
EN 17 EN 17