Advertisement
Easy steps to changing brightness
The brightness can be changed to any one of three settings.
Carry out the commands without the On Screen Display (OSD) Menu
displayed. If the OSD Menu is displayed, press the BRIGHT button
and begin when it has disappeared. (You can also make it disappear
by pressing the MENU button several times.)
1. Without the OSD Menu being displayed, push the BRIGHT button.
[
AUTO
LOW
2. Press the BRIGHT button several times to choose the brightness.
[
AUTO
LOW
3. Press the MENU button.
The OSD will disappear.
Notes:
•
The OSD Menu automatically disappears several seconds after
the last command.
•
If [AUTO] is selected, the backlight brightness changes auto-
matically for use in different surroundings.
•
After selecting the brightness (LOW, MID, HIGH), fine adjust-
ments can be made using the
Fine adjustments
Carry out the commands without the On Screen Display (OSD) Menu
displayed. If the OSD Menu is displayed, press the BRIGHT button
and begin when it has disappeared. (You can also make it disappear
by pressing the MENU button several times.)
1. Without the OSD Menu being displayed, press the
button. The BRIGHT bar will appear at the bottom section of the
screen.
[
B R I G H T
2. Adjust by pressing the
button (darker) or the
3. Press the MENU button.
The BRIGHT button will disappear.
Note: The BRIGHT bar automatically disappears several seconds
after the last command.
3-3. Manual screen adjustment
Fine adjustments can be made using On Screen Display (OSD) Menu
provided.
MENU 1:
ADJUSTMENT
Clock, Phase, H-POS (horizontal positioning) and V-POS
(vertical positioning)
MENU 2:
GAIN CONTROL
BLACK LEVEL, CONTRAST, DISPLAY COLORS
MENU 3:
WHITE BALANCE
WHITE BALANCE (color tone)
MENU 4:
MODE SELECT
OSD H-POSITION (OSD horizontal position), OSD V-PO-
SITION (OSD vertical position), 400LINES (resolution),
SCALING (level of scaling)
1. Display an image that makes the entire screen very bright. If using
Windows, you can open and use the Adjustment Pattern on the
accompanying Monitor Settings Adjustment Disk.
MID
HIGH
]
MID
HIGH
]
button or the
button.
button or the
3 1
]
button (lighter).
2. Press the MENU button.
A
D
J
U
S
T
M
E T
N
M
A
N
U
A
L
[
C
L
O
C
K
1
4
P
H
A
S
E
H
-
P
O
S
6 0
V
-
P
O
S
1
0
2
4
x
7
6
8
V
:
6
0
H
z
The ADJUSTMENT Menu will be displayed. At this point relevant
menu options can be adjusted.
Each time the MENU button is pressed, the next menu is selected.
(MENU 1
2
3
4
OSD Menu disappears)
Notes:
1. The OSD Menu automatically disappears approximately 15
seconds after the last command.
2. This explanation is based on using the Adjustment Pattern (for
Windows) to make adjustments.
3. Press the BRIGHT button to make the OSD Menu disappear.
[MENU 1: ADJUSTMENT]
A
D
J
U
S
T
M
E T
N
M
A
N
U
A
L
[
C
L
O
C
K
1
4
P
H
A
S
E
H
-
P
O
S
6 0
V
-
P
O
S
1
0
2
4
x
7
6
8
V
:
6
0
H
z
MANUAL: Individual menu options are manually adjusted.
AUTO:
Every menu option is automatically adjusted
Notes:
•
Press the
button to select AUTO.
•
To choose a menu option: SELECT button
•
To go to MENU 2:
CLOCK
The figure below demonstrates how to adjust so that vertical flicker
noise is not emitted. (
buttons)
Vertical flicker noise
PHASE
The figure below demonstrates how to adjust so that horizontal flicker
noise is not emitted. (
buttons)
Note: Adjustments to PHASE should be made only after CLOCK has
been correctly set.
Horizontal flicker noise
A
U
T
O
]
0
5
5
H
: 4
8
k
H
z
A
U
T
O
]
0
5
5
H
: 4
8
k
H
z
MENU button
Advertisement
Need help?
Do you have a question about the LL-T1501A and is the answer not in the manual?