BIRO AFMG-48-II Operating And Service Manual
Automatic feed mixer grinder, starting with serial no. 62001 mark ii, starting with serial no. 63401 side opening lid, starting with serial no. 63592 35 degrees inlet/tri directional lid
Hide thumbs
Also See for AFMG-48-II:
- Operating and service manual (16 pages) ,
- Operating and service manual (36 pages)
Subscribe to Our Youtube Channel
Related Manuals for BIRO AFMG-48-II
Summary of Contents for BIRO AFMG-48-II
- Page 1 IMPORTANT NOTICE This Manual contains important safety instructions which must be strictly followed when using AFMG-48 AFMG-48 this equipment. 138-10-13-16 138-9-05-12...
- Page 2 — NOTES —...
-
Page 3: Table Of Contents
TABLE OF CONTENTS PAGE NOTICE TO OWNERS AND OPERATORS .........1 SAFETY TIPS . -
Page 4: Notice To Owners And Operators
Warnings related to possible damage to the equipment are indicated by: BIRO also has provided warning labels on the equipment. If any warning label or Manual be- comes misplaced, damaged, or illegible, please contact your nearest Distributor or BIRO directly for a replacement. -
Page 5: Safety Tips
· NEVER Alter This Machine From its Original Form as Shipped From Factory. DO NOT Operate Machine With Missing Parts. · PROMPTLY REPLACE Any Worn or Illegible Warning Labels. · ALWAYS Read Operation and Service Manual BEFORE Operating, Cleaning, or Servicing. · USE ONLY BIRO Parts and Accessories Properly Installed. -
Page 6: Installation
UNCRATING AND SET UP 1. Read this Manual thoroughly before installation and operation. Do not proceed with installation and operation if you have any questions or do not understand anything in this Manual. Contact your local Distributor, or BIRO first. - Page 8 16. Check placement of all warning labels and Manual. Machine is now ready for trained operators to process product. 17. Use meat deflector attached to grinding bowl to eliminate meat splatter. 18. Contact your local Distributor or BIRO directly if you have any questions or problems with the installation or operation of this machine.
-
Page 9: Operation
OPERATION ROTATING GRINDING AUGER & ROTATING MIXING PADDLE TO AVOID SERIOUS PERSONAL INJURY · ONLY Properly Trained Personnel Should Use This Equipment. · NEVER Place Hands Into Machine Input or Output Openings. · NEVER Open Machine During Operation. · DO NOT Wear Gloves While Operating. ·... - Page 10 CLEANING THE BOWL - RING AND WORM CARE OF TIN COATED PRODUCTS (DO’S AND DON’TS) Do not use abrasive cleaning materials, such as Brillo pads or metal scrapers. Tin is a soft metal and should be cleaned with a soft cloth and dried. Do not use a cleaning agent containing a high percentage of free alkali or acid.
-
Page 11: Maintenance
· NEVER Bypass, Alter or Modify This Equipment in Any Way From Its Original Condition. · PROMPTLY REPLACE Any Worn or Illegible Warning Labels. · USE ONLY GENUINE BIRO Parts and Accessories Properly Installed. A. GRINDING BOWL INSTALLATION 1. Mount the grinding bowl on the three threaded studs on the front of the machine. Tighten in position with provided nuts. -
Page 15: Main Drive Chain And Sprocket Lubrication
MAIN DRIVE CHAIN AND SPROCKETS LUBRICATION (continued): Recommended types of chain lubricant are those with Molybdenum Disulphide or Graphite added. Also bonded lubricants such as Dow Corning Molykote 321R or equivalent are excellent for open chains. The lubricant should be of a viscosity whereby it will “flow” somewhat and penetrate the internal working surfaces. Thick stiff greases are of little value because they cannot work into moving parts of the chain. -
Page 16: Optional Eagle Belt Drive System
OPTIONAL EAGLE BELT DRIVE SYSTEM... - Page 19 — NOTES —...
-
Page 20: Parts Diagrams
AFMG-48 SIDE VIEW PARTS DIAGRAM... - Page 21 BIRO MODEL AFMG-48-II MIXER GRINDER PARTS LIST Fig. Item No. Description Fig. Item No. Description 57154 HHS055S -18 ´ ¾, SS Product mixer safety cover, tri directional, Hex head screw HN07S #63592 on Hex nut 10-24, SS 53547 HN15S Lid with chute opening Hex nut ¼-20, SS...
-
Page 24: Dorris Mixer Transmission Parts List
DORRIS MIXER TRANSMISSION PARTS LIST H369 -18 ´ ¾ 53769-38 Hex head screw High speed Timken cup (closed end) LW30S 53769-39 Lockwasher, SS " High speed Timken cone (closed end) 0850 -20 ´ 53769-40 Setscrew " long High speed Timken cup (open end) 1084 -13 ´... -
Page 25: Journal Box
53979-1 Cord 8’ w/o foot switch 54213 Foot switch w/ 6’ cord & plug... -
Page 26: Items Required For Tandem Operation To S/N 63591
TANDEM OPERATION PARTS LIST 272-7-1 -18 plastic knob – 3 pt. 53489 Dscg. Horn 24/42/46/48 to 24/48/52 inlet less seal 57044 Connec. brkt. AFMG52 to AFMG48 57044 Connec. brkt. AFMG52 to AFMG52 53552-1A Connecting brkt. assem. man/auto 53604 Dscg. horn 52 to 24/48/52 inlet 53667 Dscg. - Page 27 TANDEM OPERATION ILLUSTRATION FOR 90° INLET FROM S/N 62001 TO S/N 63591...
-
Page 29: Connection Instructions For Tandem Operation
CONNECTION INSTRUCTIONS TANDEM OPERATIONS AFMG-48 or ARFMG-52 INTO AFMG-48 or AFMG-52 Heavy Horsepower Grinder INTO AFMG-48 or AFMG-52 Remove Side Entrance Seal, Item No. 57133; Outer Disc, Item No. 54303 and Lock Knobs, Item No. 14688 from the inlet tube of the Second Grind Machine. Clean out the tube if necessary. - Page 30 TANDEM OPERATION ILLUSTRATION FOR 35° INLET S/N 63592 ON...
-
Page 33: Operator's Signature Page
OPERATOR’S SIGNATURE PAGE — NOTES — MY SIGNATURE ATTESTS THAT I HAVE COMPLETELY READ AND UNDERSTAND THIS MANUAL. I REALIZE THAT THIS MACHINE, IF OPERATED CARELESSLY, CAN CAUSE SE- RIOUS INJURY TO MYSELF AND OTHERS. SUPERVISOR’S NAME (PRINT) SIGNATURE DATE INITIALS... -
Page 34: Notes
— NOTES —... - Page 35 — NOTES —...
-
Page 36: Limited Warranty
BIRO is not responsible for service charges or labor required to replace any part covered by this limited warranty or for any damages resulting from misuse, abuse, lack of proper or recommended service.
Need help?
Do you have a question about the AFMG-48-II and is the answer not in the manual?
Questions and answers